Clutch plate cracked. Had to replace all parts to the final drive
Transmission & drivetrain
BMW K1200LT Transmission problems by year
37 complaints filed with NHTSA about the BMW K1200LT's transmission & drivetrain. Harsh or delayed shifting, slipping, CVT shudder, rollaway, axles, driveshafts and transfer cases.
Transmission complaints by model year
Latest K1200LT transmission complaints
Drive shaft had break, dangerous. Caused the final drive gears to break, dangerous. On the road.
Brake lines leaking and replaced. $1002. In repairs. Final drive leaking and all gear damaged.
Riding on relatively straight, two lane state road in rural georgia ( without having any previous issues). Riding approximately 45-50 miles per hour. Bike suddenly began making a clanking noise from the rear wheel. Rode approximately 20 mph for approximately one-tenth mile to store parking lot. Shut down bike and transported to my residence on trailer.
Upon arriving at work I noticed a slight oil drip onto the rear tire and brakes. When I returned home the rear tire had oil around the perimiter and the oil was leaking onto the rear brakes saturating the pads. The leaking was bad enough that I had to put a rag under the tire to keep it off the floor. I took it to an authorized bmw dealer and they replaced the crown bearing, seal, bearing roll, & o-ring. This required 2.5 Hrs of shop labor.
The final drive differential failed, locked up the rear tire, cause catastrophic loss of control, ejection from the motorcycle at highway speed, and total loss of the machine. The rider suffered moderate injuries, mostly abrasions and bruises, and broken bones. The tire pressures and final drive fluid level had been checked that day, and were correct. A $10,000 machine was totaled because of a cheap part that is a known defect, has occurred over and over, and bmw has not been ordered to fix this safety issue! *Tr
Felt a strange vibration. Exited the road at the next exit about a mile down the road. Upon slowing below 20 mph, the vibration increased. Braking was diminished and used down shifting. Pulled over into a parking lot and inspected the motorcycle. Found oil running from the final drive down the brake rotor and rim/tire. Called for a tow truck to take it to the local bmw dealer. Dealer said the final drive bearings had failed and the entire final drive needed to be replaced. Since there was a known issue with the pre-2004 final drives, the dealer replaced with a final drive from a 2006. *Tr
Odi no. [[redacted]], and currently being investigated under campaign dp12001. Oil leaked over tire and brakes. Noticed the leak when tried to stop and didn't stop as it normally did. Bmw dealer replaced final drive. *Js information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6)
Tl* the contact owns 2003 bmw k1200 lt motorcycle. The contact was driving 70 mph when the rear wheel bearings caused the vehicle seize. The contact noticed oil leaking from the final drive unit onto the rear wheel. The vehicle was towed to the dealer where the bearings, o-rings, and rear wheel shaft was replaced. The contact had not experienced any further issues with the vehicle since the repair. The failure mileage was 30,876.
Bmw k1200lt 2003 motorcyle I purchased used with 8700 miles on the bike. At 18646 having all the maintenance done by the dealer, I experienced a rumbling sound traveling on an interstate at 65 mph. I pulled over thinking it might be a bad tire and noticed oil dripping on the rear tire/rim. Oil on the rear brakes did hamper my slowing down. Bmw repaired the final drive saying the outside bearing failed causing the oil seal to fail. At 25,423 miles the final drive failed again. This is a high priced bike and I was...
Read the full complaint
surprised at this mechanical failure which I believe now that it wasn't assembled correctly and during the repair no change on the new bearing was done so it failed a second time. I finally purchased a used final drive to continue riding. I now have 129,025 on the bike and the used final drive is still performing ok so the issue was with the original drive on this bike. A new final drive wasn't in my budget. I wonder what would have happened had I been in a hard curve when this failure occurred. Not good, I'd say. Bmw can/should do better during assembly. *Kb
Same failure as described in odi no. 10439549, And currently being investigated under campaign dp12001. *Kb
Final drive required replacement for grinding, clunking and vibration. Dealer found oil loaded with bearing material and signs of an oil leak. *Kb
The linear bearing in the rear drive failed - metal flakes and bearing material appeared in the rear drive oil when the oil was changed. The oil was changed every 3000 - 400 miles and without warning the drive oil became contaminated by a bearing that deteriorated. The bearing cage had not started to fail at this time. The rear drive was removed from the motorcycle, taken apart and upon inspection the bearing was in early stages of complete failure. Upon further inspection and measurement it would appear that...
Read the full complaint
the bearing was initially over shimed (greater than the manufacturer specifications called for) at the factory placing undue forces on this linear bearing - thus causing its premature failure. The replacement bearing along with proper shims, as called for in the manufacturer specifications, were placed back into the drive. *Kb
I had the same failure as described in odi no. 10439549, And currently being investigated under campaign dp12001. While doing 70 mph on the kentucky parkway I felt a severe vibration and slight wobble in the rear wheel of the motorcycle. I slowed to the shoulder and stopped. After checking the rear tire I found a lot of gear oil on the tire, rim, and rear drive. I was extremely lucky that I did not lose traction and crash. *Kb
Second rear drive failure of 2002 bmw k1200lt motorcycle at 42502 miles first at 17520 miles. *Tt
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data