- The problem
- Chrysler (FCA US, LLC) is recalling certain 2014-2019 Ram 1500 and 2014-2020 Jeep Grand Cherokee vehicles equipped with 3.0L Diesel engines. The crankshaft position sensor tone wheel may delaminate, causing the engine to lose its ability to synchronize the fuel injector pulses and cam shaft timing, possibly resulting in an engine stall.
- The risk
- An engine stall can increase the risk of a crash.
- The fix
- Dealers will update the powertrain control module software to maintain vehicle propulsion, free of charge. Interim notification letters, notifying owners of the safety risk, were mailed August 3, 2023. Some owner notification letters were mailed October 31, 2023. The remaining owner notification letters will be mailed at a future date, anticipated July 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 66A. This recall is an expansion of recall 20V-475.
Engine & cooling
2014 Ram 1500 Engine problems
Owners have filed 348 complaints about the 2014 Ram 1500's engine & cooling with NHTSA - 19% of all its complaints, most recently on November 6, 2026. They describe 3 crashes, 15 fires and 12 injuries. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.
- Complaints
- 348
- Recalls
- 3
- Crashes
- 3
- Fires
- 15
- Injuries
- 12
- Deaths
- 0
Engine recalls for the 2014 Ram 1500
- The problem
- Chrysler (FCA US LLC) is recalling certain 2014-2018 Ram 1500 and 2014-2016 Jeep Grand Cherokee vehicles equipped with 3.0L diesel engines. The crankshaft position sensor tone wheel may delaminate causing the engine to lose its ability to synchronize the fuel injector pulses and cam shaft timing, possibly resulting in an engine stall.
- The risk
- An engine stall can increase the risk of a crash.
- The fix
- FCA US will notify owners, and dealers will update the powertrain control module software to maintain vehicle propulsion by reading the camshaft position signal in the event that the crankshaft position signal is lost, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact FCA US customer service at 1-800-853-2002. FCA US's number for this recall is W58.
- The problem
- Chrysler (FCA US LLC) is recalling certain 2014-2019 Ram 1500 and 1500 Classic Pickup trucks equipped with 3.0L Eco Diesel engines. The Exhaust Gas Recirculation (EGR) cooler may crack and allow pre-heated vaporized coolant to enter the EGR system. This mixture may combust inside the intake manifold.
- The risk
- Combustion in the intake manifold can increase the risk of a fire.
- The fix
- Chrysler will notify owners, and dealers will replace the EGR cooler, free of charge. Dealers will also inspect and, as necessary, replace the intake manifold. The recall began April 16, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is VB1.
Engine complaints
The contact owns a 2014 Ram 1500. The contact stated that after driving for an extended period, the vehicle started to shake with an unknown service warning message displayed. Despite the initial failure, the contact stated that the vehicle resumed normal operation after approximately an hour. The vehicle was taken to the dealer on several occasions to have the air compressor replaced under warranty; however, the failure persisted. The contact then switched the settings to regular suspension which appeared to...
Read the full complaint
correct the issue. The contact also stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken back to the dealer and the contact was informed that the intake manifold needed to be replaced. Upon investigation, the contact linked the failure to NHTSA Campaign Number: 19V757000 (Engine and Engine Cooling). The manufacturer was notified of the failure and the contact was informed that the vehicle was not included in the recall. The vehicle was not repaired. The failure mileage was approximately 20,000.
Check engine light came on after replacing spark plugs and coil packs. Code reads cylinder 03 misfire. Engine has a ticking noise. Cam and lifters are what's causing the check engine light. If not replaced with the upgraded cam and lifters, engine will be no good. Would be very unsafe if my engine were to blow up while driving on the freeway or around town with my children. Dodge knows these cams and lifters are junk and should replace them with the upgraded ones
The contact owns a 2014 Ram 1500. The contact stated that upon driving from a complete stop, the vehicle would not exceed 3 MPH as the safety mode engaged. The check engine warning light was illuminated. The contact parked the vehicle. The contact stated that the failure persisted the next day; however, the contact was able to drive the vehicle to an independent mechanic. The independent mechanic diagnosed that the failure was related to NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling) however, the VIN...
Read the full complaint
was not included. The independent mechanic referred the contact to a Chrysler dealer. The vehicle was towed to the local dealer, where the tone wheel crankshaft, transmission heater, exhaust temperature sensor was replaced, and the transmission fluid was flushed. The vehicle was repaired. The manufacturer was notified of the failure but declined to cover the cost of the repair. The failure mileage was approximately 86,047.
The contact owns a 2014 Ram 1500. The contact stated while reversing out a driveway, while accelerating the vehicle lost motive power with the check engine warning light illuminated. The contact turned off the vehicle and while restarting the vehicle, the vehicle was running rough. The vehicle was towed to the dealer, but the vehicle was not diagnosed. The vehicle was taken to an independent mechanic and was informed that the vehicle had experienced similar failure as NHTSA Campaign Number: 20V475000 (Engine and...
Read the full complaint
Engine Cooling) and referred the contact to the manufacturer. The manufacturer was contacted and stated that the VIN was not included in NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling). The failure mileage was 127,000.
The contact owns a 2014 Ram 1500. The contact stated while driving 50 MPH, the vehicle went into LIMP Mode and decelerated to 40 MPH. The contact was able to veer to the side of the road. The message "Service Electronic Throttle Body" was displayed. The contact continued to drive; however, the failure reoccurred several times while driving. The vehicle was taken to several independent mechanics who cleared the diagnostic codes; however, the failure persisted. The vehicle was taken to the local dealer where the...
Read the full complaint
diagnostic codes were cleared; however, the failure reoccurred while driving. The vehicle was taken to a second dealer Davis Chrysler Dodge Jeep Ram (464037 E State Rd 200, Yulee, FL 32097) where an unknown repair was completed; however, the failure persisted. The vehicle was taken to a third dealer Beck Chrysler Dodge Jeep RAM (256 Hwy 17 North, Palatka, FL 32177) where it was diagnosed that the failure was related to NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling). Additionally, the contact related the failure to NHTSA Campaign Number: 22V406000 (Fuel System, Diesel); however, the parts to do the recall repair were not yet available. The contact stated that the vehicle was not drivable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 50,000. VIN tool confirms parts not available.
I have a loud ticking noise doing startup which appears to be coming from the engine compartment. Upon further investigation, there are several owners that's having the same problem which they call the hemi tick. This should be investigated as a defect with the 5.7L engine and recalled. My vehicle was purchased new.
The contact owns a 2014 Ram 1500. The contact stated while driving at various speeds, there was a ticking noise coming from the engine compartment. No warning lights were illuminated. The vehicle was taken to an independent mechanic, where it was diagnosed that the camshaft needed to be replaced. The vehicle was not repaired. The contact referenced the failure to NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling); however, the VIN was not included in the recall. The manufacturer was not made aware of the failure. The approximate failure mileage was 120,000.
Exhaust manifold bolts have broken causing a ticking sound upon cold start. This is the passenger side. Same thing happened on drivers side a few years ago. This is a well known problem with Ram Hemi engines and should be considered a manufacturer defect and repaired free of cost
This is the second time I've reported still no recall. These 5.7 are dangerous, with virtually no miles on them, the camshafts can have a lobe warn down, from oiling issued and the faulty MDS systems in these trucks. Mine stalled in the middle of a intersection with my wife and kids, these engines are unsafe and need to seriously be reevaluated. Also the timing chain guides prematurely wear out, causing excess play in the chain and can jump time and severely loose power or even stall out completely. Recall these engines, or I will make it public via YouTube, and facebook.
The contact owns a 2014 Ram 1500. The contact stated that while driving approximately 70 MPH, the vehicle was jerking and he noticed a sudden drop in the gas mileage. No warning lights were illuminated. Additionally, the contact stated that he heard an abnormal ticking sound coming from the engine compartment. The vehicle was taken to the local dealer who informed the contact that the abnormal ticking sound could be associated with the exhaust manifold failure. The vehicle was then taken to an independent mechanic...
Read the full complaint
who diagnosed the failure as an engine cylinder misfire. The independent mechanic informed the contact that the engine would need to be dismantled in order to be repaired. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with NHTSA. The approximate failure mileage was 115,000.
in my case it's the hemi tick i took my truck to the dealer they said that i didn't have the tick now but the tech told me if I wanted to replace the lifter and cam it would cost me 6,000.00. The problem is that the oil pump doesn't pump oil into the lifter when idling it's a faulty oil pump and Chrysler isn't taken responsibility. I think it's models from 2013 to 2019 it should be a recall on those models for the oil pump and damage that it causes
My 2014 ram 1500 went to the dealership for recalls and a wheel alignment, ecm failed to recognize new software updat and will not start, new chrysler ecm installed and truck still wont accept new software so will not start. Previous experience of a bad tipm insisted on various lights coming on tachometer display, cruise control shutting off at various speeds, engine shutting down and turning off on highway at cruising or passing speeds, had new integrated tipm installed and new Altenator, resoled issues.
While driving on the interstate, towing a 17' ultralight camping trailer, the vehicle made a very loud "BANG" noise from under the hood and immediately decelerated to a much lower speed (~20MPH). I was able to maintain control and guide the truck to the shoulder as traffic was light. Upon opening the hood the large turbo inter-cooler hose had separated the black rubber section from the steel coupling in the front-drivers side area of the engine. The hose clamps had apparently failed. Upon reconnecting the hose to...
Read the full complaint
the coupling with the clamps I attempted to restart the engine and proceed. The engine started, but had a check-engine indicator. As soon as I put the truck into gear and tried to accelerate the bang noise happened again and the hose disconnected. I called a tow truck and was towed to the nearest town with a Ram dealer (30+ miles). The dealer was able to diagnose and verify the issue and also locate and replace the entire turbo inter-cooler hose and reset the check-engine indicator resolving the "limp-mode" state. The Ram service center kept the old part but provided a detailed invoice representing the failure. If the interstate was busier (it was Sunday afternoon) the situation could have been very much worse as the deceleration was immediate and other cars could have collided with the slowing truck.
The 3.6-liter V6 24-valve VVT engine which is defective and is a safety hazard. First pinging then the truck stalls out in traffic. Dodge does not stand behind the Lifetime limited Powertrain warranty they sold me when I bought the truck because the dealer, I bought it from closed. Dodge knowing these engines are defective put us customers in life threating situations because of the faulty components in these engines. They put the cost on the customers to fix the faulty rockers and lifters, valves, camshafts. So, I paid $3,400.00 to have it fixed with them installing new defective parts that will fail again and put my life in danger when the truck just stalls out.
It has the 5.7 hemi, well it's always had a hemi tick, well one day I tried accelerating threw an intersection where it stumbled and died, another car almost hit but luckily he was able to stop. Come to find out the lifter has eating my cam lobe to the point where it's missing on one cylinder. I've did some research and it seems like a very common saftey problem, that seriously needs to be addressed, along with the exaughst manifold bolts that breaks, and can cause a fire do to the exaughst leak.
The contact owns a 2014 Ram 1500. The contact received notification of NHTSA Campaign Number: 22V406000 (Fuel System, Diesel) however, the part to do the recall repair was not yet available. The contact stated that while driving at an undisclosed speed, the vehicle made abnormally loud noises and then stalled. The vehicle was towed to the dealer where it was diagnosed that the engine needed to be replaced due to fractured rods. The vehicle was not repaired. The manufacturer was made aware of the failure and a case was opened. The failure mileage was 71,735. VIN tool confirms parts not available.
Fuel sensor failure at around 100,000 miles. A quick search reveals this is an extremely common issue and even more upsetting is seeing how many people experience recurrent failures within a year of replacing. This is a major safety issue if my vehicle randomly runs out of gas on a busy highway, which is far more likely considering the sensor failure will not allow the engine to enter ECO mode. My other issue is the hemi tick which could either be the exhaust bolts or the cam going out. Why haven't these issues been recalled?
I was driving down the highway and when I went to accelerate I heard a loud "clunk" like my transmission dropped. After the loud clunk an indicator came across my dashboard stating "service electronic throttle control". I pulled off to the side of the highway shut my vehicle off and tried to restart it just to make sure it wasn't a glitch. Upon starting the vehicle again, there was a very long delay considered to be a hard start. Since the vehicle started I decided to try to merge back onto the highway but as I...
Read the full complaint
was trying to accelerate the vehicles rpm would not go past 3000 rpms and would not accelerate past 40 mph. I shut the vehicle off and had it towed home. I took the vehicle to the dealership around the corner from my home and they scanned it. The code that popped up was P0336 (crankshaft position sensor). Upon further investigation the dealer diagnosed the problem to be the Tone Wheel/Reluctor ring breaking. FCA has an open recall for this exact issue W58/W68, but my vehicle is not included because it was built for the Canadian market. Although, my vehicle is a DS model with the sales code EXF.
2014 Ram eco diesel. The high pressure fuel pump failed on the interstate while passing a semi truck. This failure sent metal throughout the entire fuel system to include; injectors, fuel lines, fuel return lines, fuel rail, and fuel tank. The truck immediately went into limp mode, then a check engine light appeared and finally a low oil pressure light. No other warnings or symptoms appeared prior to failure. I pulled on the interstate immediately as the truck had no power. All of this happened within 30 seconds or...
Read the full complaint
so. I was forced to quickly move to the shoulder and move out of the trucks way as my vehicle was emitting significant white smoke out of the exhaust. The issue is confirmed with a ram dealer in bozeman mt. Awaiting parts that are currently on back order. Been 2 months already
What component or system failed or malfunctioned, and is it available for inspection upon request? my suspension and also my engine are the first problems that i have noticed while driving this vehicle. How was your safety or the safety of others put at risk? When I drive I am scared to go even the speed limit of 30mph because my suspension makes my car bump aggressively and also there is a loud ticking noise I notice under the hood I have looked up reviews of this vehicle and seen that others have similar...
Read the full complaint
complaints for the dodge ram 2014 1500. Has the problem been reproduced or confirmed by a dealer or independent service center?] I took it into palmens dodge dealership and they didn't want to diagnose the vehicle unless the took the engine apart though they said it was better off replacing just by hearing the noise. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Not as far as I'm aware Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? the problem started towards the beginning of the new year
Vehicle engine stopped suddenly on highway while traveling 50mph. Dash message was about service electronic throttle system. Vehicle coasted to a stop without power steering or brakes. Vehicle would not restart and was taken via Wrecker service to the dealership. Tone Ring failed along with crankshaft position sensor. There are two recalls (W58 and W68) dealing with this issue for other VIN numbers in the 2014 model year. Chrysler is not acknowledging that this issue also applies to my vehicle and isn't covering the tone ring under the recall or warranty. This should be investigated as a broader application of the W58 and W68 recall.
Good morning, I am a user and owner of a RAM 1500 year 2014 and with 90,000 km I have had the problem for the second time that the screws that hold the exhaust manifolds are cut, causing fire to come out of the engine compartment, which can cause the vehicle to catch fire, this It is a typical problem in these HEMI engines, so I was talking with other owners of RAM 1500, they should make a solution to this problem since several people including are thinking of selling the unit and looking for other brands. From now cordial greetings [[redacted]] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
The contact owns a 2014 Ram 1500. The contact stated while driving approximately 65 MPH, the vehicle stalled in the middle of the highway. There were several unknown warning lights illuminated. The contact was able to veer to the side of the road. The vehicle was towed to a local dealer who diagnosed that the crankshaft position sensor was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 117,770.
When the truck is started the service shifter light comes on and will not let you shift the truck out of park. Then when driving down the road the light will come on and the truck will automatically shift in park and you can't do anything but coast of the road to stop. It's extremely hard to turn the steering to get off the road. This was fixed once at a dodge dealership and they said it was fixed and clearly it is not. This has happened to many trucks. I feel this need attention and fixed for the safety of others.
While in the process of unhitching my camping trailer, I put the truck in reverse to gently center the tow ball under the hitch when the vehicle suddenly accelerated at high RPMs and lurched backward. I braked but the engine continued racing at high speed. Braking was completely ineffective as the tires continued "burning rubber" on the pavement. My wife was helping me guide the vehicle when this occurred. The only thing that prevented an accident and serious injury to my wife and me was the trailer. The trailer's...
Read the full complaint
wheels were still chocked, but the sudden, forceful acceleration dislodged the jack stand and pushed the trailer back approximately 4 to 5 inches. The acceleration stopped on its own after approximately 30 seconds. This was a terrifying experience that had the potential for a tragic outcome. This problem has not been yet been diagnosed by a dealer or service center, as it just occurred a few hours ago. There were no warning lamps or any other symptoms preceding it.
Ram 1500 engine complaints by year
1500 engine problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data