Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Engine & cooling

2008 Saab 9-3 Engine problems

Owners have filed 68 complaints about the 2008 Saab 9-3's engine & cooling with NHTSA - 37% of all its complaints, most recently on December 30, 2020. They describe 1 crash, 0 fires and 0 injuries. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.

Complaints
68
Recalls
0
Crashes
1
Fires
0
Injuries
0
Deaths
0

Engine complaints

Engine & cooling

Defective intake valves. Repair center specializing in saab performed cold compression test on cylinders and found that 2 of 4 had low compression. Informed me that they have found 90% of the saabs they test from 2007-08 have this problem from cheap valves used specified by gm.

Filed Incident EngineNHTSA 10852843
Engine & cooling

Intake valve issue - car will not start on a cold day and, sometimes at a stop sign /light, will stall - had to two mechanics depict the issue and it is the intake valve issue - many saab's have reported this issue and nothing was done by gm - I called gm and they said that they are not responsible - this issue has been reported several times and there are several threads as well.

Filed Incident Unknown or other · EngineNHTSA 10852372
Engine & cooling

Tl* the contact owns a 2008 saab 9-3. While starting the vehicle, it idled roughly. Additionally, the vehicle would sometimes take a long time to start. The vehicle was not diagnosed nor repaired. The manufacturer was not made aware of the failures. The failure mileage was 90,000.

Filed Incident EngineNHTSA 10836497
Engine & cooling

I didn't have a problem with the car in southern california, but I moved to new york at about 75k miles - and I noticed a problem right away. Rough idling started, and would even turn on, then right back off. The problem was not an issue again during the summer months, so I was able to drive it to 83k miles. Now that it is winter time, even though it is garaged it will not start if it is under 45 degrees. I had it checked out with a certified saab mechanic and he confirmed by way of compression test that it is indeed the dreaded intake valve problem. The estimate for repair is $2,230!

Filed Incident EngineNHTSA 10836469
Engine & cooling

Hard/rough start especially in cold temperatures. Mechanic said #4 cylinder is misfiring. Confirmed to be low compression due to prematurely worn intake valves. #1 Cylinder/intake valve is not far behind #4. Became a serious problem when engine stalls when sitting in traffic. Also vehicle engine has stalled/shut off while driving at low speeds, for example, in parking lots, redlights, 4 way stops.

Filed Incident EngineNHTSA 10822436
Engine & cooling

Rough cold start. Compression on cylinder 4 to low.Intake valve problem.

Filed Incident EngineNHTSA 10807295
Engine & cooling

79,000 Miles began with sluggish cold starts until warmed than began to run o.K until stopped turning over. Another owner of gm screwing the public with crappy valves installed in these engines. When will there be enough complaints to create a recall. Ordering parts from east coast saab parts store and looking for reasonable and knowledgeable california based mechanic. Expecting to pay approximately $2k. Will update this complaint when job complete. Another gm disappointment in car ownership!

Filed Incident EngineNHTSA 10788387
Engine & coolingCrash

The engine lost total compression due to what the mechanic said was a well-documented case of intake valve failure, happened in northern california. The engine cut out while I was in traffic on the freeway, the car stopped, and the car was grazed from behind. Not much of a problem due to damage, just a quick re-paint of the back bumper, and paid out of pocket. The engine was gone. The saab specialist told me that so many 9-3's,especially on the east coast, have experienced total intake valve failure like mine. ...

Read the full complaint

I contacted saab and they essentially said to go screw myself. Saab and a subsequent call to gm claimed they had "never heard of the issue" which my mechanic specialist said was a "bold lie" because there's an online history of this that I found, and they denied me any help in getting it fixed. Since the car was worth more than the $2,900 cost I had to pay to have the engine rebuilt, with the same faulty valves that will cause someone else trouble later as I traded in my car, I decided to repair it, and then get $1,200 more out of it once I traded in my car. You need to investigate this. It is not fair to owners who are out of pocket. There was a safety concern with my incident. If the car behind me had not been aware once the freeway started moving again, I could have been hurt. Saab and gm deny this, yet search google---"intake valve problems saab 9-3" and you'll see for yourself. Make gm pay for this. People have lost a ton of money on depreciation alone, and now the engines fail, almost all of them,according to the shop who fixed my car and to what I've read online. Please issue a recall. Saab and gm were both especially arrogant to me. They should pay for this problem, and reimburse me what I was out even though I sold my car. I have the receipts if you need them. Thank you for listening! Please email only. *Tr

Filed Incident EngineNHTSA 10758980
Engine & cooling

I have the same issue that others have talked about. Gm put cheap valves in engine--they have now failed for a number of us. Cold starting, rough idle, smell of gas, ultimately will not start. Expensive repair on car without much mileage 60k repair is 2500-3000 gm should fix these for free or reduced cost.

Filed Incident EngineNHTSA 10747316
Engine & cooling

Car will not start on cold days. Found cylinders 1 and or with low compression.Intake valves need replacement.

Filed Incident EngineNHTSA 10721208
Engine & coolingFuel system

I first noticed a difference in how my car worked about a year and a half ago. I purchased it certified pre-owed from a certified saab dealer at the time. When I first noticed the "cold-starts" I thought it was just normal wear and tear and maybe needed an oil change. I always use premium gasoline and get the vehicle serviced regularly by the dealer. When I took it to the dealer in the beginning of 2014, the technician said he's familiar with the problem that I was having. He says the issue is with the...

Read the full complaint

compression valve. He told me that I was "unlucky" that I purchased this car because saab manufactured 2007-2009 9-3 model engines where the valves were made of weaker metals that when surrounding metals. As the edges of the valves impact the engine walls, their original convex designed became concave, thus causing a loss in pressure and combustion. (I'm not an engine savvy guy, so please excuse my lact of terminology). So, he quoted me about $3,000 for a valve replacement. That's rediculousness! How can gm produce a vehicle whose valves will deteriorate after normal wear and tear? This has led to not only cold starts but also decreased responsiveness on the highway. Sometimes when driving, I would apply the accelerator and my car shakes for a few seconds. When giving a ride to others they look at me like, "that's not supposed to happen." My car hasn't stalled or shut off while driving, but I'm guessing if I don't get this fixed soon it may happen. There is a safety issue that I'm sure gm is aware of; accordingly, there needs to be a recall to get this issue resolved.

Filed Incident Engine · Fuel / propulsion systemNHTSA 10716700
Engine & cooling

At about 70,000 miles the car began to start rough on cold mornings this continued on until this year 2014-2015 it would barely start on all on a cold morning, after less then a minute of running it would be smooth with no apparent lose of power. All plugs and plug ignition coils we replaced with no effect. Finally I did a web search and found out a number of 9-3 saab's 2006-2008 had bad metal in some of valves causing them to wear paper thin.Once the engine was warm the metal expanded giving normal ...

Read the full complaint

compression. A compression check on mine came back cycl 1,3,4 50lbs cycl 2 200lbs. This starting problem was first noticed at 70,000 I got the motor fixed at 92,000 miles. Of course the fix was a valve job and a cost to me of $2088.02. I feel saab (gm) should share a large portion of this cost. This problem was very well documented on all the saab forums. I hope anyone reading this and has the same problem please file a complaint this is not right. *Tr

Filed Incident EngineNHTSA 10703782
Transmission & drivetrainEngine & cooling

My 2008 saab 93 2.0T has intake valve failures. In the morning it idles rough until it warms up; this has been verified by a saab specialist. My engine is not molded or altered in anyway other than the consumables over time (belts and such). A quick check for 2008 saab valve problem leads to forums chalk full of other owners with the same issue. Gm should foot the bill for this $2500+ rebuild of the engine that they poorly manufactured in the first place. *Tr

Filed Incident Power train · EngineNHTSA 10703444
Transmission & drivetrainEngine & coolingFuel system

On the 2007-2011 saab 9-39-3 there is a common issue with the intake valve seals going bad causing a rough idle and/or misfire on cold starts. Mine exhibits this behavior but is not still under warranty. This is not just wear and tear it is a bad part or bad design that is basically designed to fail. To fix this it costs $1500+ and gm should be responsible for a flaw in the vehicle regardless of the 5 year/100,000 mile warranty. *Tr

Filed Incident Power train · Engine · Fuel / propulsion systemNHTSA 10691971
Acceleration & cruise controlEngine & cooling

Tl* the contact owns a 2008 saab 9-3. While driving at various speeds, the vehicle failed to accelerate without warning. The failure recurred numerous times. The vehicle was taken to a dealer, where it was diagnosed that the intake valve needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 80,000.

Filed Incident Vehicle speed control · EngineNHTSA 10684258
Engine & cooling

Check engine light on.. Shop found multiple engine misfires.. Checked engine compression.. Compression below manufacturers specs.. Needed complete valve job per saab recommendation.. Parts sent to machine shop for repairs and re-condition.. Re-install of cylinder head assembly with new head gasket and all other needed gasket and seals.. Flushed and refilled all engine transmission fluids.. Complete valve job with intake and exhaust valves.. Defective valve is reported issue on saab 9-3 2008.. *Tr

Filed Incident EngineNHTSA 10683665
Transmission & drivetrainEngine & cooling

We purchased a 2008 saab 9-3 in 3/2011 with 34,000 miles. As of 2/2015 the vehicle has 104,000 miles. Last month the vehicle barely started after sitting overnight and would take several minutes to reach a normal idle. It would then start the rest of the day, sometimes after a "hard" start. The check engine light came on and the mechanic said the code read as a "cylinder misfire" code. 8 Days ago the car would not start and is now sitting in my driveway. I called a saab specialist about 2 hours away from me...

Read the full complaint

who knew exactly what the problem was. He explained the intake valve problem that a lot of saab owners are experiencing due to defective materials used by gm and/or suppliers. He said the cost will be at least $2,200 but could easily be more depending on the severity. This is a known defect (a service bulletin has been issued detailing this issue) that should be subject to a recall. We cannot afford to fix an engine that does not work due to substandard valves. This is not a normal "wear and tear" issue, but an issue dealing with parts that were doomed from the beginning. *Tr

Filed Incident Power train · EngineNHTSA 10683486
Engine & cooling

Compression in cylinder one is not firing at a full psi per mfg standards. It's causing a cold start issue and the car barely turns over to start when it's not warmed up. *Js

Filed Incident EngineNHTSA 10669001
Engine & cooling

Vehicle doesn't start due to low compression on cold days. Car will leave you stranded in extreme temps. *Tr

Filed Incident EngineNHTSA 10668059
Engine & cooling

Same as problem below: since I need the car badly, I've instructed my mechanic to start working on the fix. Over time the valves in the 2.0T engine will wear causing dramatic loss in compression. Problem starts with rough idling and trouble turning over at cold start but escalates to a point where the car will not start what so ever. It appears that when manufacturing the engine gm put valves made of a softer than usual metal. These valves get essentially hammered against the cylinder head to a point where the...

Read the full complaint

edges become so thin they are razor sharp. A service bulletin was sent out to dealers from spna (saab parts north america), which means that gm is well aware of this issue. A saab mechanic warned me that the problem could get worse at any time regardless of mileage and that sooner of later my car would not start. To fix this issue all 16 valves would need to be replaced. This involves serious time and effort and I was quoted a price of up to $3,000 for a repair. Please be advised that this problem effects every saab 9-3 with the 2.0T from 2007 to 2011. Gm should be held accountable for these faulty parts and issue a recall. *Js

Filed Incident EngineNHTSA 10661960
Engine & cooling

For the second year in a row, with temperature in the teens, the car will not start due to bad intake valves. As noted by many consumers on several saab forums, this engine loses significant compression in the cylinders causing difficult starting, a very rough idle and ultimately resulting in a valve job. *Tr

Filed Incident EngineNHTSA 10660005
Engine & cooling

Engine refused to start in cold weather. Saab technician confirmed an issue with intake valves being defective. The intake valves would not seal cause compression to get as low as 40 psi causing no start condition. Saab refused to cover it under warranty on the 61st month of ownership vehicle came with 60 month engine warranty and the cost of repair out of pocket was over $2500. There were days the car wouldn't start away from home after sitting just one day, leaving me stranded in extreme cold weather with no...

Read the full complaint

heat. Gm and saab know about this issue as they got poor quality intake valves from a supplier. Gm has not yet campaigned/recalled these vehicle, as you know gm culture lacks ethics and have covered up deaths in the past to save money. As a government agency your responsibility is to protect consumers and be proactive and not act after something horrible has happened. There are more then enough complaints on this website for this issue. Are you waiting for a death to occur before anything is done ? Gm new or old should be held accountable for this issue. Its a gm ecotec engine, car was produced on a gm platform. Profits from the vehicle also went to gm. This issue also causes an increase in emissions. As there is loss of compression, cylinder misfire or has incomplete combustion causing an increase in hydrocarbons and carbon monoxide in the tail pipe. *Tr

Filed Incident EngineNHTSA 10651318
Engine & cooling

While driving vehicle p0008 engine code occurred, car was taken to an independent mechanic, mechanic stated engine code was indicated by camshaft sensor, and could possibly be a worn timing chain. This is a common issue on gm 2.8 And 3.6 Engines and gm has issued a tsb to extend the warranty for the timing chain to 120k miles or ten years. This tsb did not include the timing chain for the 2.8 Liter engine in the saab. *Tr

Filed Incident EngineNHTSA 10616588
Engine & cooling

Engine fails to start when cold and when it does, the car runs extremely rough. Car hesitates and drives poorly until engine is finally warm. Cold compression test confirms that there is low compression and that there are defective intake valves. This is a serious problem for a vehicle that is not old at all. *Tr

Filed Incident EngineNHTSA 10605050
Engine & cooling

Cold start problem caused by low compression / defective valves when cold. Runs fine after it warms up. Getting worse over time. *Tr

Filed Incident EngineNHTSA 10598882

Saab 9-3 engine complaints by year

9-3 engine problems, every year

Had a engine problem with your 2008 9-3? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience