A solder bridge on the printed circuit board within the fuse panel of the power converter passed undetected through a test fixture and bypasses the fuse protecting the circuit.
Electrical system
Winnebago Brave Electrical problems by year
8 complaints filed with NHTSA about the Winnebago Brave's electrical system. Dead batteries, warning lights, wiring, alternators, infotainment and electronic module failures.
Electrical complaints by model year
Electrical recalls
Latest Brave electrical complaints
Tl* the contact owns a 2003 winnebago brave. While driving approximately 65 mph, the vehicle began to shudder and hesitate before suddenly stalling and shutting off. During the incident, an electrical burning odor was present inside the cabin. The vehicle was towed to the dealer where it was diagnosed that the electrical wires connecting the ignition switch were faulty and a protection kit was installed to remedy the failure. The manufacturer was not notified. The failure mileage was 70,462.
While climbing a steep grade, entire vehicle started to shake due to continuous engine power surge. Vehicle is still being diagnosed, but is believed to be caused by wiring damaged caused during assemble of housing to chassis. *Tr
Parking brake on vehicle locks up when vehicle is stopped and will not release. Vehicle cannot be moved. Parking brake also tries to engage while traveling down the highway. This has occurred six times since 2011. Each time the parking brake pressure sensor is replaced and one time the parking brake shoes were replaced as well. There is also a leak in the actuator. We have been unable to fix this without the problem occurring again and again. *Tr
Vehicle component design and operator usage concern: when shifting in or out of low gear (automatic transmission w/ column shift), during beginning/completing a steep descent, shift lever sometimes hits the ignition keys and turns "off" the ignition. This occurs, occasionally, when the steering column tilt position is in one of the two lowest positions. Due to engine braking effect, simply turning the ignition back "on" keeps the engine running. If ignition is not turned back to "on" position, steering...
Read the full complaint
and braking become difficult. This is primarily a problem due to the number of keys on a typical motorhome, which I now prevent by separating the keys. I have also learned to tilt the column position up when driving in conditions that require frequent shifting in and out of low. *Tr
Dt: the contact owns a 2002 winnebago brave that is on a work horse chassis. After driving the vehicle approximately 2 hours he stopped at a rest area about 110 miles from his home. When he tried to restart the vehicle it would not start and nothing would operate. There was no power going through the ignition switch to start the engine. There were no warning indicator sounds nor was there power to the dashboard instruments. After further evaluation a mechanic determined that the ignition switch and the...
Read the full complaint
connectors to the switch had melted. Upon trying to locate an ignition switch the mechanic contacted the dealer. The service dealer stated that there was a kit available to remedy this problem. The contact has tried to contact the manufacturer, but no one has returned his calls. *Ak
Dt: the vehicle is a rv, 2001 winnebago brave wpf30w. The ignition switch overheated and caused the engine to shut down while in use. The engine failure then caused the emergency brake to kick in automatically. This happened three times while the consumer was driving. The first time it occurred was in august -2003, the second time it happened in january -2005, and the third it occurred was on 9-5-2005. The most recent time it occurred the consumer was almost in a serious accident. The consumer had...
Read the full complaint
the vehicle repaired multiple times. The ignition switch was replaced after the first time. The second time they replaced the wiring harness to the ignition switch. Currently, they are getting ready to replace the ignition switch again. When the switch was replaced the first time the consumer was given the switch and when he took it apart he could tell it had melted. The second time the wiring harness plug at the switch had melted. *Ak *mr
No warning - engine stopped running and lost all engine electric including headlights, turn signals, brake lights and emergency flashers. Power wire to abs system burned to exhaust header, loose bulk head connector and blown 40 amp & 60 amp fuses. Replaced fuses, repaired wire and tightened bulk head connector. *Jb
While driving 50 mph the engine stopped running and all electrical power ceased. Brake lights and hazard warning lights were rendered inoperative. We could not get entirely off the road so not having hazard warning lights was very dangerous for oncoming traffic as well as us. There was a strong smell of electrical wire burning but no further fire was found. Neither the chassis or coach manufacture take responsibility for not having a fail safe system for brake lights and hazard warning lights not being opperational. *Ak
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data