The weld that holds the different sections of the frame of the motorcycle has a crack. The weld from the manufacture is defective. The crack is in parallel and in the middle of the weld. It is clearly visible on both sides of the bike just below the gas tank. The crack can cause the bike to fall apart during riding putting the rider and nearby traffic in mortal danger.
Body, doors & structure
Yamaha FZ1 Body problems by year
11 complaints filed with NHTSA about the Yamaha FZ1's body, doors & structure. Doors, hoods and latches, frame rust, sunroofs, leaks, trim and structural failures.
Body complaints by model year
Latest FZ1 body complaints
The frame has cracked at the frame weld point on the right side. This is the manufacturers weld from Yamaha. This is a known issue that has affected hundreds of thousands of 06-07 Yamaha FZ1 motorcycles. Yamaha knows of their welding error and chooses to do nothing about it.
I noticed the frame is cracked on the weld on the right side!!! The bike has never been dropped. This is a manufacturing defect!!!
Tl* the contact owns a 2006 yamaha fz1. While driving 40 mph, the motorcycle felt unstable. The contact pulled over and noticed that the frame of the motorcycle had folded and subsequently collapsed. The contact saw that the frame had failed and fractured in half. The motorcycle was not taken to a dealer or mechanic. The dealer was not contacted. The motorcycle was not repaired. The manufacturer was made aware of the failure and was deciding on a course of action. The approximate failure mileage was 18,000.
I own an early 2007 fz1 motorcycle. The machine is in mint condition with only 15,000 miles. On february 25th 2016 I noticed a large crack in the frame weld on the right side. It starts at the bottom and climbs the weld over 2 inches, cleanly through to the other side. For the past month I have been stressing day-in and day-out trying to solve this nightmare. I've brought the machine to my local authorized dealer and submitted a repair order only to get a quote of $3500 to replace the frame. I've spent countless...
Read the full complaint
hours and days going back and forth with customer relations staff just to be told "you're on your own on this one" and "there's nothing I can do." There's no doubt this was a manufacturing defective weld because no matter how long the warranty, the frame is the backbone of the machine and should last beyond the machines lifetime. With the 06's having the same issue I can see how it carried into some 07's before being fully corrected. Upon researching the issue further, I discovered hundreds of others with identical cases that had better luck and their replacement expenses covered by yamaha. Needless to say I'm extremely disappointed thus far and hoping to have the replacement expenses covered by yamaha.
Frame cracked along factory weld on the right side inside/outside vertical and lower horizontal. The motorcycle has never been dropped or crashed and passed maryland state safety inspection yesterday. When washing the bike today, I noticed a linear crack that ran vertically along the weld on the right side of the frame below the tank. No wrecks, excessive stress or temperature change preceded crack. The bike had only made a 3 mile trip from the inspection station to my home when I noticed the crack. This is clearly a manufacturing defect and it is an outrage that these frames weren't recalled for safety.
My son and myself went for a short ride in the warm of the day after attending church. After riding about an hour we stopped at a friends house where the friend came out to check out my bike.We then noticed the crack on the right side of the frame just above the engine.The crack goes all the way down the weld line of the frame and under the bottom of the frame in the weld line,could be on the back side of the frame also,but the bike would need to be disassembled to inspect any further. *Tr
Motorcycle right side frame weld above clutch engine cover was found with a crack. The crack in the weld appears to run along the outside of the frame and continuously under the frame and back up the inside of the frame. The motorcycle has never been involved in a crash. The frame weld has just failed. *Tr
On the right side of the motorcycle, there is a weld that connects the upper part of the frame to the lower part of the frame. The weld is located just above the clutch cover. The weld has developed a center line crack. Upon further investigation on a fz1 forum, this is an issue other with the 2006 and 2007 fz1 owners have had.
2007 Yamaha fz1, build date 12/2006, experienced a significant weld failure in the frame. Right side of frame, on the weld seam below the fuel tank. This is a well known and established issue for the first year and early production of the second year for this generation of this motorcycle. *Tr
Tl* the contact owns a 2006 yamaha fz1. The contact stated that while driving 50 mph over a small hill, a popping noise was heard. The contact then turned right and the frame cracked in half along the frame welds. The contact then lost control of the motorcycle and crashed into a ditch. There were no other damages to the motorcycle or the driver. The motorcycle was towed to the dealer, who contacted the manufacturer. The manufacturer offered no assistance. They stated that there were no recalls or warranties...
Read the full complaint
addressing the failure. The manufacturer also stated that the frame must have been cracked prior to the failure. The police were not notified. The vin was unknown. The failure mileage was 56,000.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data