Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Engine & cooling

1994 BMW 325I Engine problems

Owners have filed 4 complaints about the 1994 BMW 325I's engine & cooling with NHTSA - 24% of all its complaints, most recently on April 6, 2010. They describe 0 crashes, 1 fire and 0 injuries. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.

Complaints
4
Recalls
1
Crashes
0
Fires
1
Injuries
0
Deaths
0

Engine recalls for the 1994 BMW 325I

Engine and engine cooling: cooling system

98V178000340,000 vehicles affected

The problem
Vehicle description: passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.
The risk
If a crack were to form or a seam were to separate in the heater core end piece, hot coolant could suddenly be expelled, increasing the risk of personal injury to a vehicle occupant.
The fix
Dealers will install a new design radiator cap to control pressure and provide greater coolant overflow in the event of overheating.

Engine complaints

Engine & coolingVisibility & wipersSeats & seat beltsElectrical systemFire

Tl* the contact owns a 1994 bmw 325i. The contact stated that the odometer reading was incorrect. The mileage indicated that the vehicle had 28,000 miles when the title indicated that the mileage was 128,000. The vehicle was taken to the dealership for a diagnostic test. The dealer advised the contact that another mechanic had altered the odometer. The contact also noticed that the anti-freeze was leaking, the front windows fogged and the seat belts were defective. The vehicle was at the dealership awaiting repair at the time of the complaint. The approximate mileage was approximately 28,000. The current mileage was unknown.

Filed Incident Engine and engine cooling · Visibility · Seat belts · Electrical systemNHTSA 10324050
Engine & cooling

The radiator cap failed prior to recall notice 98v-178, the consumer believes this is due to improper radiator design. Nlm

Filed Incident Engine and engine coolingNHTSA 561568
Engine & cooling

The problem deals specifically with the location of the supply hose (part of the engine cooling system) from the reservoir tank to the radiator. The first time this problem happened was on the date of this report. It was taken back to the dealer and repaired under factory warranty. The second time it happened was about a year ago. The supply hose is located right under the fan shroud. It is held up by 2 clamps that are molded onto the fan shroud. This whole assembly (shroud and clamps) appear to me to be a plastic...

Read the full complaint

material. What has happened is that the supply hose has come lose from the clamps that are molded onto the shroud on 2 different occasions. The first time it sheared off 2 fan blades and was repaired under factory warranty by the dealer. The second time it came loose it the hose sheared off all of the fan blades thus causing the engine to overheat to the poitn the engine was ruined. The piston completely turned over in the cylinder causing the engine to lock up. Apparently what happens is over time these clamps moled onto the shroud become hot and brittle thus making it possible for them to eventually break off. Due to the location of the supply hose once it comes loose from these clamps it falls directly into the fan blades. The loose hose cannot avoid the fan. I have looked at many other makes of automobiles since this happened the last time. In all of the other automobiles that I have looked at the supply hose is engineered in such a manner that if it did come loose from the clamps it cannot become entangled with the fan blades. It couldn't even come close! Based upon this knowledge I believe that bmw has erred in the design of the cooling system, at least on the 3 series. It is still designed that way today. I have talked to bmw of north america about this several times to no avail! I would appreciate (if you have time) a phone call so that I could explain this problem better! Thank you! Sincerely, danny l. Smith. *Ak

Filed Incident Engine and engine coolingNHTSA 719024
Engine & cooling

Recall component failed prior to recall (98v-178), consumer is having trouble getting reimbursement.

Filed Incident Engine and engine coolingNHTSA 547604

BMW 325I engine complaints by year

325I engine problems, every year

Had a engine problem with your 1994 325I? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience