- The problem
- Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.
- The risk
- If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.
- The fix
- Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.
Electrical system
2008 Chrysler 300 Electrical problems
Owners have filed 524 complaints about the 2008 Chrysler 300's electrical system with NHTSA - 69% of all its complaints, most recently on November 4, 2026. They describe 9 crashes, 8 fires and 6 injuries. Dead batteries, warning lights, wiring, alternators, infotainment and electronic module failures.
- Complaints
- 524
- Recalls
- 1
- Crashes
- 9
- Fires
- 8
- Injuries
- 6
- Deaths
- 0
Electrical recalls for the 2008 Chrysler 300
Electrical complaints
Odometer Fraud. The contact purchased a 2008 Chrysler 300. The contact discovered that there was a mileage discrepancy after purchasing the vehicle. The vehicle was a private sale. At the time of purchase, the vehicle's mileage was 136,000. It was later discovered upon checking a Carfax report with a local dealer, the mileage was 183,000.
The contact owns a 2008 Chrysler 300. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 14V567000 (Electrical System); however, the repair failed to prevent a failure from occurring. The contact stated that several days after the recall repair was completed, the contact had to adjust the ignition switch to start the vehicle. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 68,000.
The contact's friend owns a 2008 Chrysler 300C. The contact stated that while his friend was starting the vehicle, there was an abnormal burning odor entering the vehicle through the vents. The contact was informed that there was an unknown warning illuminated. The contact's friend was no longer able to start the vehicle. Additionally, the key fob was not able to unlock the doors. The contact stated that the key fob battery was replaced; however, the vehicle was no longer starting. The contact had not taken the...
Read the full complaint
vehicle to a local dealer or independent mechanic. The vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 14V567000 (Electrical System) however, the VIN was not included. The failure mileage was approximately 160,000.
The contact owns a 2008 Chrysler 300C. The contact stated that while driving at an unknown speed, the vehicle lost motive power without warning. The vehicle failed to restart and was towed to the residence. The contact stated that an independent mechanic was unable to determine the cause of the failure; however, the mechanic stated that the failure could be related to the ignition switch. The contact stated that the vehicle was able to start intermittently; however, the contact stopped driving the vehicle due to a...
Read the full complaint
fear that the failure might recur while driving with his family. The contract stated that the vehicle was serviced under NHTSA Campaign Number: 14V567000 (Electrical System) in 2020. The dealer was contacted and stated that he had to pay for a diagnostic test and repair since the vehicle was previously repaired under the recall. The manufacturer was not notified of the failure. The failure mileage was 186,145.
For the axle or the wheel bearings or something like that every time I turn the wheel to a certain angle it pops also has hard vibration while driving the buttons have fallen off the seats the steering pulls to the right has rust by the gas tank 0102 since banks sensors have one out and has stopped starting occasionally have replaced key fob but it occasionally still happens and the flow sensor alert is coming on for the code airbag recall needs done the wheels pressure sensor gauge never turns off for the alert...
Read the full complaint
I've had to have my car towed three times because I'm non-start and engine light is still on also dangerously the heat shield had come apart on my car just recently 2020 super dangerous while driving
The dealer changed the ignition switch per the recall 14v567000 for the vehicle about 2-3 years ago for a different issue with the switch. My daughter was driving the car about week ago july 30, 2020, she said she was at a traffic light on a busy street (lincoln highway) in chicago heights il and when it turn green she attempted to go and the vehicle cutoff and would not start back up. I arrived to her location. Another driver had pushed her into a parking lot to get her out of the middle of the highway, I tried...
Read the full complaint
to start the car and it would not catch. It would crank put not turn over, I had to get it towed home. After some testing of components, spark, gas pressure and fuel pump it was diagnosed with a bad ignition switch with a p2533 code that stated there was a problem with the ignition switch run position signal. This is a very troubling event since my recently turn 18 daughter has no experience with this sort of thing and thankfully there was no accident or physical harm done. I spoken with a person at a chrylser dealership service department about manufacturer coverage but she did not have a clue and transferred my call to the parts department that stated it might run $800- 1,000.00 To replace the switch.
It seems chrysler doesn't have the correct fuel pump ! They sell my 3 different ones and all do not work. They even match it with the vin! I can't get one to work and I spent thousands. A lot of others on 300 forums have had the same issue !! So many 6.1 And higher that need that fuel pump but chrysler seems to keep sending me parts and taking my money! Please help
I bought this vehicle, thinking it was great. I tried driving it home, and never made it. I lost all power on the highway in front of the semi. In return I did not have brakes, I didn't have steering, all lights turned off, and to top it off it wouldn't start again. I've replaced the pcm, starter, alternator, the power distribution, all the fuses/relays, and here I am still spending hundreds of dollars to try to get my vehicle to work again, and it's not seeming possible. I have 2 kids and now once I get it started...
Read the full complaint
I must worry if it'll happen again. The car only has 120,000 miles on it. It's been very well kept. And now I've bought all these parts and paid all this money to have it repaired. And now I'm out of my other vehicle, and with the corona virus I am out of work, and have no way to keep spending money to fix it or find out the problem. The electric light was on I replaced throttle and sensor as well. That didn't fix it neither.
Car will turn off when driving out of nowhere and I have to restart the car all over again. It has happened several times one time as I was turning into a street another time as I was switching lanes. This last time I was at a stop light and the car did it again.
I was driving on the highway and my car just stopped working died. Wouldnt turn back over. Had to tow it home hasnt moved since
I had a recall to replace ignition switch, had it replaced and returned to shop and they told me that the starter is going out. Replaced starter and the ignition is doing what the recall stated. Sometimes it starts on acc and sometimes not at all. So I replaced the starter when it was the switch all along.
You have a chrysler recall p57. This exact problem happened to my 2008 chrysler 300 walter p. Chrysler signature edition but my vin is not included in your recall. It cost at least $1,000 to fix this out of pocket. Please expand your recall so I can be reimbursed for this costly repair.
The igition switch has been replaced few years back on a recall and now having the same problem again. Car is hard to start
Tl* the contact owns a 2008 chrysler 300. The contact received a recall notice for nhtsa campaign number: 14v567000 (electrical system). The recall repair was performed by scott robinson chrysler dodge jeep ram (424-299-8800, located at 20900 hawthorne blvd, torrance, ca 90503), but the remedy was insufficient. After the repair, the vehicle was unable to start. The contact scheduled a diagnostic appointment with glenn e. Thomas dodge chrysler jeep (2100 e spring st, signal hill, ca 90755, (562) 426-5111). The manufacturer was notified of the failure. The approximate failure mileage was 105,000.
Tl* the contact owns a 2008 chrysler 300. While driving 25 mph, the vehicle stalled without warning and crashed into a curb. The contact then noticed smoke coming from the passenger side of the vehicle under the hood. The contact also smelled a burning odor within the cabin of the vehicle. The fire department was contacted. The hood was opened and an off duty fireman was able to extinguish flames coming from the alternator. A police report was not filed. The vehicle was not towed. The contact stated that the...
Read the full complaint
vehicle remained at the scene awaiting the insurance company to make arrangements to have it towed to jeep chrysler dodge ram fiat of ontario (located at 1202 auto center dr, ontario, ca 91761, (909) 906-7097) for diagnostic testing. The vehicle was not repaired. The manufacturer was contacted and opened case number: 35164546. The approximate failure mileage was 120,334. *Dt*jb
Tl* the contact owns a 2008 chrysler 300. The contact stated that the vehicle failed to start and the traction warning indicator illuminated. Once the vehicle was started, after several attempts, the indicator turned off. The vehicle was taken to snethkamp chrysler dodge jeep ram (11600 telegraph rd, redford charter twp, mi 48239, (313) 429-0013) where it was diagnosed that the ignition needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 110,105.
On 1/31/18 I took my chrysler 300 in for three recall (p57) (r25) and (s43) when I pick my car up I was told that recall p57 was not done due to part being on back order and it would be 2 or 3 weeks. On 2/1/18 I recived a call from dealership reminding me of appointment 0n 2/2/18 to bring my car in for recall issues p57 that they had part so I did. After picking my car up on 2/2/18 I was on my way home and made a stop and when I got back in my car it would not start, so I contacted the dealership and they told me...
Read the full complaint
that what they did would have nothing to do with the car not starting but if I needed a tow truck to bring the car to them they would look at it, but if it wasn't caused by what they did I would have to pay to have it fixed. My car had no issues till the dealership fixed the 3 recalls, now it wont start and the ignition makes a clicking noise when u try to start it and cant move shifter out of park. Also no recall stickers were put in the engine compartment showing that a recall issues was fixed and it shows on line that the recall issues still has not been done. What can I do about this.
I had the ignition control module replaced in april 2016 due to recall. Today I am having the same problem with the vehicle not starting. When I turn the ignition to start position, there is a pause, and nothing happens. I have ruled out a new battery, starter, alternator faults. Research has narrowed it to the pcm, tipm, or the wireless ignition node. Have made an appointment with the chrysler dealer to diagnose further. The vehicle was stationary in my driveway.
Sometimes while driving the car just shuts off with out warning and starts right up after turning off ignition and restarting. It appears to be some issue with the electronic key fob or ignition connection. Of course when a mechanic looks at the issue it seems to work. Scary and dangerous. Happened since we bought it off & on.
Tl* the contact owns a 2008 chrysler 300. When the vehicle was started, the wireless ignition node module was stuck between the run and start position. The key did not remain in the run position. The contact also stated that the failure occurred three other times. The vehicle was not taken to the dealer for diagnostic testing. The vehicle was taken to an independent mechanic who determined that the wireless ignition module failed and needed a spring replaced. The manufacturer was not notified of the failure. The approximate failure mileage was 37,783.
Last year p57 recall was performed on my vehicle now they told me that the tipm module is going bad I believe that that was replaced or should have been replaced when the recall p57 was performed I don't know why they would not replace it now I'm being told that I have to pay $1691 for parts and labor there is a class action lawsuit against chrysler this is a real problem for some reason they have not put in a recall and the recall p57 did not fix the problem it is very unsafe the car stalls out in the middle of...
Read the full complaint
driving sometimes it will not start at all it is obviously an ongoing issue since 2007 but for some reason chrysler refuses to issue a recall this is the third recall that I have had to get done on this vehicle in a year the s43 was never sent to me the only way I found out about that recall is when I call chrysler about my car stalling and not starting at all I need someone to look into it I don't see why I should have to pay for a faulty product that is in millions of vehicles by the chrysler dodge and jeep brand
Vehicle tipm is faulty and car does not start. This occurred after vehicle was involved in an accident, it worked for about two weeks and later stopped out of nowhere. Vehicle had to be towed.
Tipm is bad casing a no start issue and the car will periodically stall and not restart leaving you stranded in the middle of the road.
Tl* the contact owns a 2008 chrysler 300. The contact stated that the vehicle failed to start when the key was turned in the ignition. In addition, the contact stated that the windows, air conditioner, and radio also failed to function. The vehicle was not taken to a dealer. The vehicle was not diagnosed or repaired. The vin was included in nhtsa campaign numbers: 14v567000 (electrical system), 15v313000 (air bags), and 16v352000 (air bags). The manufacturer was not made aware of the failures. The approximate failure mileage was 259,000.
Tl* takata recall. The contact owns a 2008 chrysler 300. The contact called the dealer (phillips chrysler jeep dodge ram, 3440 s pine ave, ocala, fl 34471 (352) 732-7577) to schedule the repair for nhtsa campaign number: 14v567000 (electrical system). In addition, the vehicle was included in nhtsa campaign numbers: 15v313000 (air bags) and 16v352000 (air bags). The dealer stated that they replaced the air bags, but the contact was not aware. The dealer was to reprogram the keys, but made no mention of the recall...
Read the full complaint
repair for the air bags. The dealer stated that the key would need to be replaced by the contact. The dealer later called the contact to indicate that they would provide a solution for the electrical recall. The dealer did not give a specific date for when the two air bag recalls had been repaired without the contact's authorization. The manufacturer was contacted to address the electrical recall and the two air bag recalls. The contact had not experienced a failure. Parts distribution disconnect.
Chrysler 300 electrical complaints by year
300 electrical problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data