- The problem
- Sprague wiper assembly pivot can seize due to galvanic corrosion between the zinc-plated steel shaft and the bronze bushings.
- The risk
- This corrosion can cause wiper arm/blade assembly to stopwiping windshield, this could affect driver visibility and result in anaccident.
- The fix
- Replace sprague wiper assembly pivot with an assembly not susceptible to galvanic corrosion.
Vehicle safety record
1989 Kenworth T400 Problems, complaints & recalls
No owner complaints about the 1989 Kenworth T400 have been filed with NHTSA. It is covered by 3 recalls, the latest in June 1991 for the linkages.
NHTSA data checked
FFar more problems than a typical T400 year, for its age
- Complaints
- 0
- Recalls
- 3
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
1989 Kenworth T400 recalls 3
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Rear axle stabilizer (sway) bar may not have been properly heat treated.
- The fix
- REPLACE THE STABILIZER BAR.
- The problem
- Trailer wiring harness connector could cause intermittent or total failure of trailer brake lights or all of the trailer lights.
- The risk
- This would affect other drivers ability to see thetrailer and could result in an accident.
- The fix
- REPLACE TRAILER WIRING HARNESS CONNECTOR.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
No complaints about the 1989 Kenworth T400 yet
Kenworth T400: every year compared
All T400 years1989 Kenworth T400 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1989 Kenworth T400 | 0 | 3 | F | |
| 1989 Kenworth Conventional Series | 1 | 0 | - | Compare |
| 1989 Kenworth Kenworth | 1 | 2 | C | Compare |
| 1989 Kenworth T600A | 1 | 3 | D | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1989 Kenworth T400
Does the 1989 Kenworth T400 have any recalls?
Yes - NHTSA lists 3 recalls for the 1989 Kenworth T400: linkages (June 1991); rear (March 1991); wiring (March 1989). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
How many complaints has the 1989 Kenworth T400 had?
None have been filed with NHTSA so far.
Is the 1989 Kenworth T400 a reliable vehicle?
Its Safety Index is 16 out of 100 (grade F: far more problems than a typical Kenworth T400 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
What should I do if my 1989 Kenworth T400 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data