Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Body, doors & structure

Mack CXU612 Body problems by year

4 complaints filed with NHTSA about the Mack CXU612's body, doors & structure. Doors, hoods and latches, frame rust, sunroofs, leaks, trim and structural failures.

Body complaints by model year

YearBody complaintsCrashesInjuriesRecalls
20111000
20103000

Latest CXU612 body complaints

2011 Mack CXU612SuspensionBody, doors & structure

I am a maintenance mechanic for a large trucking firm. On 4 oct 2011, I checked the torque on the 5th wheel bolts of unit 11054 because I could see that the 5th wheel was sliding on the frame. The bolts were defective - yielding prior to reaching the recommended torque of 236 ft.Lb. I adjusted the torque wrench to 200 ft.Lb., Its lowest setting, and could not get any of the bolts to hold. I replaced all ten bolts with 5/8" grade 8 hardware instead of the factory 16mm 10.9 Metric because that was all we had available. There was no interference between the 5th wheel bolts and the huck rivets on the frame rail. The bolts were weak. *Tr

Filed Incident Suspension · StructureNHTSA 10434361
2010 Mack CXU612Body, doors & structureEquipment & accessories

Mack has been selling over the road trucks with substandard bolts holding the 5th wheel to the frame. As a mechanic with abf, I am seeing trucks every day with 5th wheels that are loose. On 22 september 2010, I worked on unit #10222 at the little rock shop. This truck had only 4376 miles on it and I could turn the 5th wheel bolts with one hand using a 10 inch combination wrench. I tried to torque the bolts to specs, but they only stretched. I replaced the bolts with aftermarket bolts which tightened normally. *Tr

Filed Incident Structure · Trailer hitchesNHTSA 10358965
2010 Mack CXU612Body, doors & structureEquipment & accessories

As a mechanic contracted to maintain abf road tractors, I worked on unit 10064 on 9/22/2010. I discovered that the 5th wheel mount bolts were all loose. This truck had only 51,285 miles of service pulling pup trailers! I removed the bolts to make sure there was no thread damage, lightly oiled them, and attempted to torque them to mack specs of 235 ft.Lbs. Torque. None of the bolts would tighten properly, all of them stretched. I replaced all of the bolts and tagged the defective bolts for mack warranty. As a...

Read the full complaint

citizen who expects the highways of the united states to be safe for travel, I am asking the odi to find out why all of the macks delivered to abf have defective 5th wheel mount bolts and to find out if the macks delivered to more demanding customers ( such as loggers, gravel trucks, concrete trucks, and tandem axle full trailer load truckers ) are also assembled with inferior quality fasteners that fail prematurely. *Tr

Filed Incident Structure · Trailer hitchesNHTSA 10357085
2010 Mack CXU612Body, doors & structureEquipment & accessories

I am a mechanic for abf freight system. I have observed that many of the mack trucks we use in our road fleet have premature failure of the fasteners holding the 5th wheel coupler to the truck frame. I worked on unit 10016 on 9/21/2010 and checked the 5th wheel bolt tightness as a follow up to complaint #10356665. The bolts were loose after only 63,450 miles of service. I tried to tighten them as I had previously been ordered to do but the bolts only stretched. I replaced the 5th wheel bolts. The old bolts that had been tightened were visibly stretched. *Tr

Filed Incident Structure · Trailer hitchesNHTSA 10356871

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience