PACCAR Incorporated (PACCAR) is recalling certain 2021-2025 Peterbilt and Kenworth vehicles, equipped with Bendix EC80 Advanced Electronic Control Units (ECU). Please see the recall report for a complete list of models. Electrical noise and low signal to...
Brakes
Peterbilt 389 Brake problems by year
3 complaints filed with NHTSA about the Peterbilt 389's brakes. Spongy or hard pedal, ABS faults, brake failure, noises, parking brake and brake fluid leaks.
Brake complaints by model year
Brake recalls
PACCAR Incorporated (PACCAR) is recalling certain 2019-2022 Kenworth T880, W990, Peterbilt 567, 579, 389, and 2022 Peterbilt 536, 537 wrecker and auto hauler vehicles. The work brake (winch brake) may unintentionally disengage the service brakes during...
PACCAR, Inc. (PACCAR) is recalling certain 2021-2022 Peterbilt 367, 389, 567, and 579 vehicles. The cross member mounted Hill Start Assist valve assembly may have insufficient clearance to the rear axle, causing damage to the rear brake hose and loss of the...
PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Peterbilt 367, 389, 567, 579, and 587 trucks manufactured from May 23, 2014, to February 13, 2015, and 2015 Kenworth T270, T370, T440, T470, T660, T680, T800, T880, and W900 trucks manufactured...
PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings...
Paccar is recalling certain model year 2012-2013 kenworth t170, t270, t370, t440, t470, t660, t700, t800, w900, and peterbilt 320, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 vehicles, manufactured from january 31, 2011, through january 19...
Paccar is recalling 1,043 my 2008-2009 kenworth c500, t2000,t660, t800 and w900 trucks equipped with bendix mv-3 dash control valves. The molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double...
Certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 106, "Brake hoses." The tubing was manufactured with only four layers of nylon...
Latest 389 brake complaints
ABS tone rings are prone to premature corrosion and rust jacking causing the ABS system to fail along with the traction control. This corrosion causes the rings to warp prematurely. Not only is this an expensive and time-consuming fix, but it is also an extreme safety hazard. This condition has been noted on several trucks in the Fleet along with other local companies in the area.
OEM pressed-on cast iron/stamped rings fail prematurely due to regional rust jacking, disabling the vehicle's ABS. Explicitly mention that the current design creates a systemic safety risk in cold-weather states and that a recall mandating corrosion-resistant materials (like stainless steel) is required. This cost thousands of dollars to repair and only lasts 2-3 years. Almost everyone I know with these trucks have experienced this problem. Peterbilt is highly aware of the situation, but they refuse rectify it because it only affects cold weather states.
The contact owns a 2024 Peterbilt 389. The contact stated while driving at various speeds, the vehicle experienced an inaccurate reading of the adaptive cruise control, causing the cruise control to disengage. Additionally, the contact stated after driving for an hour, the ABS, traction control, and electronic stability control warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V915000 (Service Brakes, Hydraulic, Electrical System), which the contact related to the...
Read the full complaint
failure. The vehicle was taken to the dealer for the recall repair. The dealer informed the contact that the recall repair had been performed. The contact stated upon test-driving the vehicle, the failure persisted. The dealer was informed that the recall repair had not corrected the failure. The vehicle was not yet repaired; however, the dealer charged a labor fee. The contact declined to pay the fee and the vehicle remained with the dealer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 180,000.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data