- The problem
- BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
- The risk
- An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
- The fix
- This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
Engine & cooling
2012 BMW 128I Engine problems
Owners have filed 6 complaints about the 2012 BMW 128I's engine & cooling with NHTSA - 19% of all its complaints, most recently on May 19, 2026. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.
- Complaints
- 6
- Recalls
- 1
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Engine recalls for the 2012 BMW 128I
Engine complaints
Prior to August 2024, this vehicle operated with zero check engine lights or drivetrain faults. In August 2024, BMW of Pittsburgh executed federally mandated Safety Recall 23V-707, which required opening the cylinder head. Immediately following this service, the Check Engine Light began illuminating persistently.On or about October 3, 2024, an independent diagnostic scan at Bobby Rahal BMW pulled BMW Factory Code 002A89: Exhaust VANOS Camshaft Mechanism Fault (Mechanical Sticking/Flow Restriction). Technicians at...
Read the full complaint
Bobby Rahal BMW explicitly instructed me to return the car to BMW of Pittsburgh because they suspected the original VANOS safety recall repair was botched.On October 28, 2024, I returned the vehicle to BMW of Pittsburgh to address this issue. Their technicians opened the engine block assembly a second time, yet failed to correct the defect. Following this second visit, the check engine light continued to come on intermittently. The vehicle began suffering rough idling, difficulty starting, and dangerous stalling events during operation. Cycling the ignition on and off provided only temporary relief.The check engine light has now become permanently illuminated. The safety hazards have severely escalated into a protective engine "limp mode," causing violent drivetrain shuddering and a catastrophic loss of driveability. BMW of Pittsburgh refuses to honor the recall workmanship, demanding a predatory $6,000 out-of-pocket teardown fee to bypass their liability. The manufacturer (BMW North America) has been notified under Case Reference VH78028, but the safety defect remains unaddressed, and the vehicle is completely unsafe to drive.
Due to BMW using plastic parts when you live in Hot and cold environments the plastic begins to mold to other plastic parts and pvc diaphragms tear rather easy causing rough idle , stalls and can cause over revving and send a car into another car while in gear. The cheap plastic cause oil leaks and when oil gets low cause engine failure as well.
On February 25, 2026, BMW of South Miami performed the VANOS safety recall repair on my vehicle. The repair order documented that VANOS bolts were missing and retrieved from the engine oil pan and that VANOS components were serviced. Within approximately 24-48 hours of picking up the vehicle, the check engine light illuminated and the vehicle began operating abnormally, including rough idle and irregular shifting. The vehicle stored diagnostic fault code P054B (camshaft position timing over-retarded), which...
Read the full complaint
directly relates to camshaft timing and the VANOS system involved in the recall repair. I returned the vehicle to the dealership for further diagnosis. The dealership stated an aftermarket camshaft position sensor with two O-rings was installed and removed one O-ring to correct the gap between the sensor and the camshaft reluctor wheel. The faults were cleared and the vehicle was returned to me. However, the check engine light returned again the following morning upon cold start, indicating the issue was not corrected. My service advisor has since stated that replacing the camshaft position sensor is not part of the recall repair and the dealership has declined to repair the vehicle under the recall. Because the malfunction appeared immediately after the VANOS safety recall repair and involves the camshaft timing system connected to VANOS operation, I believe the recall repair may not have been properly completed or corrected. I am requesting that NHTSA review this matter as a potential recall effectiveness issue, as the safety recall repair appears unresolved and the vehicle continues to experience faults related to the system that was repaired.
The contact owns a 2012 BMW 128I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
The contact owns a 2012 BMW 128i. The contact stated after completing an oil change at the dealer and starting the vehicle, the RPM started fluctuating. The contact stated that after coming to a complete stop at a traffic light, the RPM fluctuated rapidly and the vehicle decelerated while driving. The dealer was notified of the failure and advised the contact to take the vehicle back to the dealer for a diagnostic test. The contact was able to drive to the dealer at a slower speed. The dealer diagnosed that the...
Read the full complaint
VANOS (Variable Nockenwell Steuerung) system needed to be replaced. The dealer informed the contact that the failure was a manufacturing defect; however, she would be responsible for the cost of the repair. The manufacturer was notified of the failure and informed the contact that they could not assist since an unknown recall was converted to an extended warranty repair which had expired. The vehicle was not repaired. The failure mileage was 79,769.
The contact owns a 2012 BMW 128i. The contact received notification of NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
BMW 128I engine complaints by year
128I engine problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data