- The problem
- Certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. The affected filters are marked with a date code a61451 through a72571 sequentially. The date code and part number appear on the filter housing. Fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. The gasket of the oil filter becomes more pliable under high temperatures and pressures.
- The risk
- This condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.
- The fix
- Honeywell will replace the affected oil filters free of charge. The recall began during november 2007. Owners can contact fram customer service toll-free at 1-800-890-2075.
Vehicle safety record
1992 Chevrolet Blazer Problems, complaints & recalls
Owners have filed 280 complaints about the 1992 Chevrolet Blazer with NHTSA, most often about the brakes (207) and the electrical system (15). Those complaints describe 48 crashes, 9 fires, 16 injuries and 1 death. It is covered by 6 recalls, the latest in October 2007 for the equipment. For comparison, the 1991 has 228 and the 1993 has 521.
NHTSA data checked
FFar more problems than a typical Blazer year, for its age
#8 most complained-about 1992 vehicle
- Complaints
- 280
- Recalls
- 6
- Crashes
- 48
- Fires
- 9
- Injuries
- 16
- Deaths
- 1
Most common 1992 Chevrolet Blazer problems
Share of all 280 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
1992 Chevrolet Blazer recalls 6
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Certain replacement fuel filters, fram brand name p/n g3727, with date codes x52911 through x60801 sequentially or x600141 and a mexico country or origin marking on the fuel filter housing manufactured from october 18, 2005, through march 21, 2006, sold for use on the vehicles listed above and on certain school buses. (To see the school bus engine sizes, click on "document search" and then "bus applications"). The connector on the fuel filter was not manufactured to honeywell's specification. As a result, the o-ring may not seat correctly on the fuel line.
- The risk
- This condition may cause an inadequate seal at the connection, potentially leading to a fuel leak. In the presence of an ignition source, a fire could occur.
- The fix
- Honeywell will notify owners and replace the fuel filters free of charge. The recall began on october 18, 2006. Owners may contact fram customer service at 1-800-890-2075 (option 1).
- The problem
- Certain r&b, inc. Central multiport fuel injection (cmfi) fuel return lines, models help 55163, napa balkamp 700-3270, and the connection 2560001, sold for use as replacement equipment for the vehicles listed above. The fuel return line has a mechanical bleed valve which was not installed at the proper torque.
- The risk
- A fuel leak can occur at the valve, possibly resulting in a fire.
- The fix
- R&b, inc. Will notify owners and at the customers request, either replace the fuel line or offer a full refund. The recall began on may 4, 2006. Owners may contact r&b, inc. At 215-712-5330.
- The problem
- Certain pro-a motors corner lamps, turn signals, and headlights sold as replacement lamps for use on certain passenger vehicles listed above. Some combination lamps that are not equipped with amber side reflectors fail to conform to federal motor vehicle safety standard no. 108, Lamps, reflective devices, and associated equipment.
- The risk
- Without the amber reflectors, the vehicle will be poorly illuminated, possibly resulting in a vehicle crash without warning.
- The fix
- Pro-a motors will notify owners and offer to repurchase the lamps. The recall began on april 3, 2006. Owners may contact pro-a motors at 323-838-2988.
- The problem
- Vehicle description: certain 4-wheel drive pickup trucks and sport utility vehicles equipped with abs (antilock braking system) manufactured from september 1989 through august 1996. Under certain driving conditions the switch which signals the abs system whether the vehicle is in 2-wheel or 4-wheel drive can malfunction causing increased stopping distances during abs stops while in the two-wheel drive mode.
- The risk
- If this occurred at a time when minimum stopping distance was required, a vehicle crash could occur without prior warning.
- The fix
- Dealers will replace or repair the 4-wheel/2-wheel drive switch.
- The problem
- Severe corrosion due to road salt at the joint of the stamped steel center section and the cast outer section can cause the sections to separate.
- The risk
- Separation of the rotor sections can cause loss ofbraking ability in the affected wheel. This could result in increased stoppingdistance and/or loss of vehicle control and an accident.
- The fix
- Replace the front brake rotors with new rotors with a corrosion protection coating. However, if replacement of brake linings are necessary, it will be done at owner's expense since brake linings are normal maintenance items.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
280 complaints about the 1992 Chevrolet Blazer
Newest first, as filed with NHTSA by owners. Page 1 of 12.
02/01/2022 Windshield wiper fails to function unless the circuit board is replaced. GM refused to replace the board for 1992 vehicles even though that same board was recalled for 1994 and later vehicles. Simply said it was not part part of the recall so I had to buy a replacement myself. Was GM recall #98043 expanded to cover 1992 & 1993 year vehicles as well? ABS breaking ( or lack there of) is another matter. Upon entering my Blazer's VIN number into the NHTSA recall system, it revealed six recalls had been...
Read the full complaint
issued for 1992 Blazers. Unfortunately my VIN was not recognized other than that it was in fact a 1992 Blazer of some sort. Chevrolet simply said 1992 Chevrolet VIN numbers were not in their records. When GM/ Chevrolet fails to supply the data for my vehicle, does it have an obligation to inspect my vehicle to determine if it in fact has a problem that should have been resolved? Or has already been resolved? Or wasn't even a recalled vehicle at all? I would appreciate a reply to these questions and/or a reference to a site, providing this kind of information. Campaign Bulletins stated Dealers should confirm vehicle eligibility through GMVIS or DCS Screen 445 before beginning campaign repairs. How is this information accessed today? Really appreciate the ongoing effort to minimize avoidable accidents! .
Tl*the contact owns a 1992 chevrolet blazer. The contact has been experiencing brake failure with the vehicle. Whenever the vehicle comes to a stop, she must exert maximum pressure to depress the brake pedal. The vehicle has not been taken to a dealer. Through online research, the contact discovered nhtsa campaign id number 93v119000 (service brakes, hydraulic:foundation components:disc:rotor). The manufacturer stated that the vin was excluded from the recall. She believes that the vehicle should be included in the recall since the failures are identical. The failure mileage was 43,000.
Tl*the contact owns a 1992 chevrolet blazer. The brake lights illuminated and the vehicle was taken to a mechanic. On two occasions, the diagnosis was that the brake modules needed to be replaced at the cost of $1,000 each time. The vehicle has been to the mechanic at least ten times for the abs. The contact has never received a recall notice for nhtsa campaign id number 99v193000 (service brakes, hydraulic:antilock). The current mileage was 214,856 and failure mileage was 91,721. *Updated 08/04/08 *bf
Abs light is on & has been coming on but going off ....Was not aware there was a recall til a friend told me to check it after I had a wreck!!!! I now found out that the abs might have had something to do with it...Due to my wreck I am going to be seeing a doctor for my injuries .... I was going around a curve when I went to slow down a little bit ...I was going 25...& My truck slid & when I went to turn to go around the curve my truck jerked to the left & I hit a barrier, and now I am unable to drive my truck .... Failures: brakes & abs system. *Tr
Dt*: the contact stated the vehicle's windshield wiper circuit board was defective causing the windshield wipers to not consistently operate. The service dealer offered to fix the vehicle.
Consumer's vehicle was in a line of traffic stopped when the vehicle suddenly experienced sudden acceleration. This caused the vehicle to rear end another vehicle. Consumer contacted the dealer to see if this vehicle was recalled for any related failures. *Ak the vehicle was taken to the dealer but they were unable to locate a problem. *Nm
I am complaining about the 1990's chevrolet blazers. Several consumers have reported to me the same problem. The dash that is didital showing the mileage, spedometer and gas consumption goes out after a period of time and is defective which makes the vechicle unsafe because I cannot see how fast I am going, and gas consumption. I truly beleive this is a defective part. I spoke to a couple of business's that deal with this type of repair and I was informed that it would cost over one thousandy should of informed the...
Read the full complaint
consumers that ther was a possiabliit dollars to repair and I was also informed that they were aware of many of these parts going out making this a defective part. I feel that chevrolet. *Ak
While driving at any speed, the abs light stayed on at all times. When the consumer had to use the brakes in an emergency situation there was not enough stopping distance to bring the vehicle to a safe stop. The manufacturer is aware of the problem. *Jb
I have replaced the following items on this 1992 chevy s-10 blazer in the year and a half that I purchased it: 1.Egr valve 2.Throttle control sensor 3.Spark plugs and wires 4.Rotor and rotor button 5.Muffler system 6.Pcv valve 7.Fuel injector cleaned twice 8.Oxygen sensor 9.Lower ball joints and idler arm the first 8 items were replaced because of rough idling, smoke and sluggishness, and excessive use of gas($75.00 In a week). I also have a issue with peeling paint on the roof and sides of my truck, it is peeling...
Read the full complaint
in patches and the grey primer underneath is showing, this makes the truck look very bad.I was not aware that this was a major defect in this vehicle until recently and I want to find out how this can be fixed.
While driving at highway speed suddenly the accelerator pedal went to the floor and vehicle accelerated at a high speed. Brakes failed to hold when they were depressed to slow the vehicle down. As a result the vehicle impacted a pole. *Ak
While driving and without prior warning all electrical components went completely out, causing poor driver visibility. *Ak
Consumer states while driving all of electrical components went out. Cause unknown.*Ak
The vehicle abs light stayed on all the time, which meant that the abs systems was inoperative. *Nlm
Vehicle uses excessive amount of fuel, replaced egr valve, throttle control sensor, oxygen sensor, cleaned fuel injector, replaced pcv valve, spark plugs, spark plug wires and still has rough idle and sometimes jerks forward when brakes are engaged. Also the service engine soon light frequently comes on reading a codes for the emissions system. Sometimes expels black smoke, and heavy smell of gas when first cranked. Could nhtsa help with this? *Nlm
THE BRAKES FAILED WHEN ATTEMPTED TO STOP.*JB
Windshield wiper motor failed while driving in the rain. *Jb
The heater core was replaced three times in less than 5 years.*Jb ph
While driving in a storm, the wiper motor failed, consumer had to pull over to repair it, an inspection disclosed several defective solder connections that had corroded on the circuit board in the wiper motor, consumer believes that recall 98v150001 should be expanded to included his models year. *Mj
While the consumer was driving, suddenly the hood latch broke and completely covered the windshield causing hood to obstruct drivers view, also the vehicle crossed both lanes of travel striking the guardrail on the berm. Ohio traffic crash report (10-90-107) *yh
I received a recall notice from chevrolet approx 3 weeks after my daughter's accident. They have performed testing, but said the tests are inconclusive and deny responsibility. The 4-wd test indicated no prob. But the veh. Was not in 4wd at the time of the accident. Good weather and road conditions, skip marks indicate to me that the abs did in fact failed or malfunctioned. Product liability person is very difficult to contact, but finally got back with me and told me to have the damages repaired, then they...
Read the full complaint
will do the recall work on the brakes. If there is no problem with the brakes, then why would they do the recall work? I feel we are being deceived and need help resolving this with chevrolet. The recall notice clearly states there is a problem and it may result in longer stopping distances and possibly a vehicle crash. It sure did. I thank god that my daughter was not seriously injured or killed because of their delay in getting a recall notice out on a 1992 vehicle!!!*Ak
Left upper ball joint broke without warning,lost control of blazer. Bulletin sequence no. 190 Service bulletin no.300800 , Nhtsa item number sb619031. Date of bulletin, 08/00. Covering all years. Part nomber for ball joints have never changed on nhtsa campaign id number 011018000 component: suspension:independent front control arm upper ball joint recall date 1/07/02 1996 blazer/ gm has agred to replace upper ball joints at no cost . There seems to me a pattern of service bullitens over the years...
Read the full complaint
to make sure to check ball joints and then in 1996 agree to replace them at no charge. I talked to gm about this, failure of upper ball joints on my blazer . With the same part no. For joints also the new ball joints installed are the same part no. They gave me no answer said they are glad that no one was hurt , something is very odd here on this problem . And then they said goodbye. *Ak
Recall 99 v 193 000/abs: whenever brakes are applied in panic stop it causes a delay in stopping distance. Dealer notified. Feel free to provide any further information.*Ak
NO SUMMARY LISTED FOR ABOVE VEHICLE. *AK
While traveling at 40mph, left rear tire tread commenced to separate. 1992, Chevrolet, blazer. Tire size p205/75r15, dot# apulab1122; was original equipment. Manufacturer was not notified. Consumer still has original tire.*Ak *slc
Consumer's husband was traveling about 8mph ,turning inside of a parking lot where his wife was standing waiting for him to pick her up, husband went to apply brakes, vehicle jumped forward and pinned her up against another vehicle, and crushing her left foot severely. Dealership was aware of problem. Abs antilock braking system was defective. *Ak
Chevrolet Blazer: every year compared
| Year | Complaints | Recalls | Grade |
|---|---|---|---|
| 1996 | 1,161 | 11 | F |
| 1995 | 1,233 | 11 | F |
| 1994 | 637 | 7 | F |
| 1993 | 521 | 7 | F |
| 1992 | 280 | 6 | F |
| 1991 | 228 | 7 | F |
| 1990 | 33 | 4 | C |
| 1989 | 40 | 4 | C |
| 1988 | 41 | 4 | C |
1992 Chevrolet Blazer vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1992 Chevrolet Blazer | 280 | 6 | F | |
| 1992 Toyota 4RUNNER | 53 | 3 | C | Compare |
| 1992 Nissan Pathfinder | 32 | 0 | B | Compare |
| 1992 Ford Explorer | 0 | 7 | A | Compare |
| 1992 Chevrolet Astro | 137 | 5 | D | Compare |
| 1992 Chevrolet Beretta | 57 | 1 | C | Compare |
| 1992 Chevrolet C1500 | 41 | 2 | F | Compare |
| 1992 Chevrolet 1500 | 20 | 0 | D | Compare |
| 1992 Chevrolet C15 | 14 | 0 | C | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1992 Chevrolet Blazer
Does the 1992 Chevrolet Blazer have any recalls?
Yes - NHTSA lists 6 recalls for the 1992 Chevrolet Blazer: equipment (October 2007); fuel system, gasoline (May 2006); hoses, lines / piping, and fittings (May 2006); exterior lighting (March 2006) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 1992 Chevrolet Blazer?
By the complaints owners filed with NHTSA, the most common problem areas are the brakes (207), electrical system (15), seats & seat belts (14).
How many complaints has the 1992 Chevrolet Blazer had?
280 complaints have been filed with NHTSA, the first on June 2, 1992 and the latest on February 2, 2022. Of these, 48 describe a crash and 9 a fire, and together they report 16 injuries and 1 death.
Is the 1992 Chevrolet Blazer a reliable vehicle?
Its Safety Index is 7 out of 100 (grade F: far more problems than a typical Chevrolet Blazer year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Chevrolet Blazer years have the most complaints?
1995 (1,233), 1996 (1,161), 1997 (774). See every Chevrolet Blazer year compared.
What should I do if my 1992 Chevrolet Blazer has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data