- The problem
- Chrysler (FCA US LLC) is recalling certain 2018 Chrysler Pacifica vehicles. The front axle halfshafts may have been incorrectly assembled, preventing the shaft from being properly secured to the constant-velocity (CV) joint.
- The risk
- If the axle shaft disengages from the CV joint, the vehicle will have a loss of drive or allow the vehicle to move while in the "Park" position. Either condition may increase the risk of a crash.
- The fix
- Chrysler will notify owners, and dealers will replace the left or right halfshaft assembly, free of charge. The recall began September 18, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U80.
Transmission & drivetrain
2018 Chrysler Pacifica Transmission problems
Owners have filed 159 complaints about the 2018 Chrysler Pacifica's transmission & drivetrain with NHTSA - 18% of all its complaints, most recently on November 2, 2026. They describe 4 crashes, 0 fires and 1 injury. Harsh or delayed shifting, slipping, CVT shudder, rollaway, axles, driveshafts and transfer cases.
- Complaints
- 159
- Recalls
- 2
- Crashes
- 4
- Fires
- 0
- Injuries
- 1
- Deaths
- 0
Transmission recalls for the 2018 Chrysler Pacifica
- The problem
- Chrysler (FCA US LLC) is recalling certain 2019 Jeep Cherokee vehicles and 2018 Chrysler Pacifica non-hybrid vehicles. A component in the transmission may not have been welded properly, possibly causing the transmission to not transmit engine power to the wheels.
- The risk
- If the transmission weld fails, the vehicle will stop moving, increasing the risk of a crash.
- The fix
- Chrysler will notify owners, and dealers will replace the transmission, free of charge. The recall is expected to begin September 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U85.
Transmission complaints
The contact owns a 2018 Chrysler Pacifica. The contact stated that while driving uphill, the vehicle was shaking uncontrollably. Additionally, the Auto START/STOP feature intermittently failed to restart the engine while depressing the accelerator pedal. The vehicle was taken to an independent mechanic where a diagnostic test indicated that the passenger's side CV axle camshaft was defective. Upon investigation, the contact discovered NHTSA Campaign Number: 18V493000 (POWER TRAIN) and 18V492000 (POWER TRAIN); and...
Read the full complaint
associated the failure with the recalls. The dealer was notified of the failure and later informed the contact that the vehicle was not included in the recalls. The contact stated that the check engine warning light was illuminated. The failure mileage was approximately 170,000.
The engine powertrain system failed, specifically a catastrophic failure of the cylinder head gaskets alongside a stretched engine timing chain. The replaced components were discarded by the repair facility following the completion of the service and are not available for inspection. The failure caused a sudden, severe engine malfunction accompanied by a rough idle and immediate loss of smooth powertrain operation. Sudden engine failures of this nature create a severe hazard when operating on backroads or public...
Read the full complaint
highways, as they can cause unexpected stalling, a complete loss of motive power, or sudden deceleration in active traffic, significantly increasing the risk of a collision. The diagnosis of the blown head gasket and stretched timing chain was formally confirmed and documented by an independent service center (Rusty's Auto Service, Repair Order #118288). The vehicle has not been inspected by the manufacturer, police, or insurance representatives. It was inspected and repaired strictly by the independent service center. The vehicle experienced a sudden, momentary rough idle and rapid coolant loss without any prior overheating indications or warning lights. These symptoms appeared immediately prior to bringing the vehicle in for a professional diagnostic inspection.
My van has been reliable for 5 years until recall 73B was performed. Ever since it's install I have had 7 repair attempts and 250+ days out of service. Each repair attempt is preceesed by check engine lights, service hybrid system, check electronic throttle control, red wrench, blind spot temporarily unavailable, (occasionally) service airbag, service shifter, and stability control lights. Chrysler has been unable to fix this issue. They have replaced the abs module, 12v battery, can bus's, wiring, battery coolant...
Read the full complaint
heater, eflite motors and reducers, 400v battery, and the under hood wiring harness. Engineering has been involved, star cases opened, and technicians flown in to address these issues. The DTC code scans reveal many communication codes, both active and permanent. The last scan had 23 active codes. No one can tell me if this van is safe to drive, I don't think it is. I have had no drive events, and lost power steering momentarily at highway speeds. The latest incident had the messages start appearing at 45 mph. This can is unfit to be on the road, and stellantis does not seem to be able to fix it
The transmission shifts harshly, clunks when shifted into Drive or Reverse, and hesitates before suddenly lurching. Engine RPM rises before the transmission engages, and some describe the resulting jolt as feeling like being hit from behind. The steering wheel locks stiffly during gentle turns to the right, then suddenly releases causing a jolt back to the left at times, all other times it requires a hard pull of the wheel manually to get the steering to...
Read the full complaint
release, which also causes a hard jerking to the opposite direction. Battery and stop/start system: Repeated Auxiliary battery replacements which power the stop/start system and warning lights. On 5 occasions the Aux battery has been replaced and within a week the system fails with no diagnostic readings identifying the cause. This leads to harder drains on the main battery. The main battery (purchased from Autozone, has been replaced on warranty because it never makes it past the 2-year mark) occasional starting difficulties, and inconsistent stop/start operation. Dash Screen: The screen freezes or turns blank while operating the vehicle. Complete loss of cabin temperature control. At other times the display will freeze on the Chrysler brand logo and is completely unresponsive to any haptic touch. The software just freezes. Even after complete shutdowns and time outs the display does not reset immediately. It's a coin flip if it's going to work. These problems have been ongoing since I purchased the vehicle in 2019. Dealerships have recognized them and consistently say that until Chrysler is forced to fix this the Dealerships can't do anything about it without charging me repairs/replacement.
The contact owns a 2018 Chrysler Pacifica. While the contact's son was driving at an undisclosed speed, the shifter module warning light illuminated. The dealer was contacted by phone and was made aware of the failure. The vehicle was towed to the dealer where it was diagnosed with a shifter module failure. The contact was informed that the shifter module needed to be replaced. The vehicle was repaired; however, the failure reoccurred. While the contact's son was driving at an undisclosed speed, the brake pedal was...
Read the full complaint
depressed; however, the vehicle failed to stop as intended. In addition, the steering wheel failed to turn in the intended direction and several unknown warning lights illuminated. The vehicle was driven to the residence. The contact stated that the following day, the vehicle was started; however, the gear shifter failed to shift as needed. The dealer was contacted by phone and made aware of the failure. The vehicle was towed to the dealer, and the battery was replaced, but the failure reoccurred. The dealer was contacted by phone and made aware of the failure. The vehicle was towed to the dealer; however, the failure was not duplicated. The contact was informed that the failure was possibly caused by the wiring harness. The vehicle was not repaired. The contact was informed that the parts were discontinued. The manufacturer was contacted by phone, and a case was filed. The failure mileage was approximately 82,000.
The contact owns a 2018 Chrysler Pacifica. The contact stated that while driving at an undisclosed speed, the vehicle became difficult to maneuver, and the vehicle stalled. The message "Power Train" was displayed on the instrument panel. The failure occurred on several occasions. The vehicle was towed to a dealer where it was diagnosed and determined that the auxiliary battery needed to be replaced. The vehicle was repaired; however, the failure persisted. The manufacturer was notified of the failure. The failure mileage was approximately 120,000.
While driving the vehicle the minivan will lose all acceleration. There is usually a preceding error displayed on the dashboard to pull over immediately. The dealership has thus far been unable to fix it.
While driving, the vehicle unexpectedly shut off without warning. The engine stalled while the vehicle was in motion, causing an immediate loss of acceleration and power. This created a serious safety hazard in traffic. The issue is consistent with the condition described in Safety Recall U01 for 2017 Chrysler Pacifica vehicles involving the Powertrain Control Module (PCM). However, this vehicle's VIN is not included in the recall despite exhibiting the same symptoms.
I had my cylinder heads, valves and head gasket replaced over a year ago and drove 15k miles and i am having the same issues again. The Dealer is trying there very best not to honor my valid powertrain parts warranty like saying the head gasket is only covered for 12 months and denying my claim but my cylinder heads and top end have a 3 year 100k mile warranty since they were installed not to long ago and they are trying to deny my claim using the head gasket. I have seen and read online that these engines all have similar problems with the head gaskets.
The van fail GA state emissions with code p2797. I have to the end of July to get the tag. I went to the state for a repair waiver control # s1174706. I told them this code is under a tsb it fell on deaf ears. I. Took the van back to the dealership for a third time a different dealership they say they did the procedure for the tsb code p2797 butt didn't fix the code to pass GA emission. Tsb are good for the automotive industry but if the tsb and engineers procedures didn't fix the p2797 code than the tsb need to...
Read the full complaint
be moved to a recall program. The dealership was good at explaining that the van needs a new transmission that cost the customer 13,000.00 to replace and 3000 for new struts. The van was bought Sept 2025 and the payoff is 13,000.00. The problem is have is will not pass GA state emissions, a code thats not related with emissions cover under a tsb that should have fix it at the dealership.
2018 Chrysler Pacifica with the 3.6L V6 engine had a check engine light turn. At same time a vibration started, which was most noticable when the car was in idle. Also, a foggy exhaust started at the same time. No temperature or other warnings were occuring. After driving it to the repair facility the car was not able to be turned on. The findings are that there is a headgasket leak and radiator failure that resulted in coolant entering into the cylinder. That resulted in either hydrolock or engine overheating,...
Read the full complaint
causing engine failure. Again no temperature warning or other indication of a major issue was provided. The likely repair is a full engine and radiator replacement. It appears that many other Chrysler Pacifica vehicles have reported similar issues with the 3.6L Pentastar engine. No recall is currently available for the 2018 Chrysler Pacifica for this issue, however, it looks like the older versions (~2011-2013) have had a recall for similar issues. I have reached out to Chrysler Corporate and requested support on this repair.
This is related to the 23V-010 / XE1 recall and extended warranty for the 2018 Chrysler Pacifica Hybrid Limited. The manufacturer is refusing the recall remedy because the catastrophic nature of the failure (transmission rupture) makes it impossible for the dealer to pull diagnostic codes. This creates an impossible standard for the consumer and effectively nullifies a federal safety recall. On [redacted], I brought my 2018 Chrysler Pacifica Hybrid Limited to D'Ambrosio Service in Downingtown, PA. I reported...
Read the full complaint
that the car was making a sound during acceleration. On April 16, I was advised that the noise was the rubbing of the heat shield which was reportedly adjusted and tested that the noise was gone. On April 19 I sent a message to D'Ambrosio that the noise remained however I never received a response. I believe that the noise was misdiagnosed and was actually warning signs of an imminent transmission failure. On [redacted], while driving, my wife and I heard a pop, saw smoke pouring out the back and immediately pulled over to discover a large amount of fluid spilling out of the bottom of the vehicle. The vehicle was towed to D'Ambrosio service in [[redacted]] where it has remained unaddressed until June 10. On [redacted] I received a phone call from D'Ambrosio that the vehicle transmission had a hole in it (quote from service advisor "internal failure of the transmission, which has caused components to puncture the casing") and would need to be replaced at my cost. When I inquired about the XE1 warranty extension, I was told that the lack of diagnostic codes didn't justify the warranty. I then asked that the issue be escalated INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Odometer 66466. Hybrid battery charge level 100%. When starting the vehicle the issue started with the transmission shifter knob stuck in gear Park. After turning off and on a few times, the transmission shifter knob would shift into Reverse. I then drove it to a dealer service for repair. During the drive several dash warning messages appeared. Also, the blind spot warning system did not function and the backup camera did not function. Dash warning messages while driving to dealer service: Parking Brake, TPS,...
Read the full complaint
Service Electronic Stability Control, engine, Red wrench, amber throttle, Brake, Service Electronic Throttle Control, Service Hybrid Electric Vehicle System. stability control, Blind Spot Alert, Arrived at dealer, kept engine on, brought service tech rep to vehicle and demonstrated the issue while in service bay. Mileage 66474. Last message I saw, Service Hybrid Electric Vehicle System. Friday, April 10 2026. The vehicle was in the shop for Service Hybrid Electric Vehicle System just 750 miles previous to this system failure. Dealer is unable to fix problem. Hybrid System still under warranty. Hybrid battery replaced last year, 12 volt battery replaced twice after. Vehicle is beyond unreliable, there is significant risk of failure at any time.
The manufacturer's mandatory 73B Safety Recall update (Vehicle Fires) creates a critical software-induced communication failure on the central vehicle network. Following the 73B flash, the vehicle developed an Active SGW U0001-00 CAN C Bus network fault, which permanently blocks data transmission and triggers an HCP U0412 hybrid battery fault. This network crash disables the hybrid propulsion systems, creating an unpredictable and hazardous driving condition. The manufacturer (Stellantis) and its authorized dealer...
Read the full complaint
(Seattle Jeep) are refusing to remedy this safety recall side effect under the vehicle's Hybrid Powertrain Warranty, instead forcing consumers to pay out-of-pocket diagnostic fees ($284.67) and multi-module software update fees ($812.50) to correct a defect injected by the recall software itself. This directly compromises vehicle safety and violates federal recall remedy mandates.
In reference to recall query RQ24004, the appropriate software was installed under recall O3A for Loss of Motive Power on my 2018 Chrysler Pacifica Hybrid. However, on multiple occasions the vehicle has displayed "Stop Safely - Vehicle Will Shut Off Soon". Once on 6Apr2026 and again on 13Mar2026. The first occasion occurred on a winding mountain road enroute to a ski hill. The road was extremely busy at the time and pulling off was difficult and dangerous with only a small snow covered shoulder. The second...
Read the full complaint
occasion occurred on I-15 during rush hour. Again pulling across multiple lanes of traffic and stopping along the shoulder was dangerous. The dealer seems reluctant to do anything other than re-flash i.e. update the software again. A brief internet search demonstrates that often the software is insufficient to fix the problem.
2018 Chrysler Pacifica PHEV subject to Safety Recall 73B (NHTSA 24V-536) for HV battery fire risk. Following the recall repair at Fremont CDJR (Newark, CA) in January-February 2025, this vehicle has experienced systematic cascading hybrid drivetrain failures across 5 repair visits totaling 57 days out of service: (1) CAN bus star connector failure - 10 modules with fault codes U0103/U0001; (2) Hybrid Control Processor failure - required 14 flash attempts to program; (3) $1,786.67 repair failed within 23 miles - CEL...
Read the full complaint
and BRAKE warning light appeared simultaneously; (4) Complete transmission removal required to replace auxiliary transmission fluid pump (DTC P2797-00); (5) Power Inverter Module replacement still pending. Vehicle also disabled itself completely while driving prior to March 2026, requiring 30 minutes rest before it could be driven. All failed components are part of the integrated hybrid drivetrain disturbed during the recall repair. Request investigation into whether Recall 73B repairs are being performed correctly at authorized FCA dealers and whether other owners are experiencing similar post-recall failures.
The van has just approx 55000 miles. While driving on highway, it suddenly lost power and from 60mph it came down to 20 miles in a matter of few seconds after few violent jerks. I was lucky that no vehicle was behind me. After that I pulled a side and then again started. It kept jerking and loosing power. Very carefully I got it to a mechanic. They are checking but they say looks like transmission issues. Engine light also came on. This happened few months ago however it was not this bad and my mechanic looked...
Read the full complaint
and he could not find anything. That problem went away after that incident. Kindly advise what to do in this situation. Chrysler Pacifica 2018 This van has lots of problems in other crucial area also like air fender switch, oil hose and cover that went bad as they are made of plastic. Then the trans mounts broke. It costed me dearly. Please Advice what to do? Best regards [[redacted]] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Engine experienced premature valvetrain failure (camshaft/lifter issue) at approximately 145,000. Vehicle developed ticking noise, misfire, and loss of power. Diagnosis confirmed camshaft/lifter damage requiring major repair. This appears to be a known issue with the 3.6L Pentastar engine and is documented in Chrysler STAR case S2309000013. Failure creates potential safety concern due to loss of power while driving. Vehicle is out of warranty, and manufacturer has not provided consistent support for repair despite known pattern failures.
Have lost power steering intermittently while driving.
While I was driving the car started beeping and all dashboard lights started flickering. Transmission started stuttering and engine rpm fluctuating wildly. Fortunately I was in my neighborhood and was only going about 15 mph and was able to pull to a stop. The issue is with a faulty star bus connection near the glove box. After watching a you tube on the same issue, I learned to hit the area near the glove box to reset the star bus connection. This has happened before but usually on startup. Dealer not...
Read the full complaint
able to repair after $1600 charge. This is the first time it happened while in motion. Again. Seems to be a common enough issue that there are several you tube videos with thousands of views.
While driving vehicle suddenly, and randomly, has a loss of engine response whole pressing the accelerator. Engine randomly shuts off while parked or at a traffic light, and can be difficult to restart after causing a traffic hazard.
Chrysler Pacifica 2018 about 56000 miles. Transmission seal is leaking that's manufacturing defect. Chrysler is denying the warranty as this vehicle in not in recall for repair. Please advice Thanks [[redacted]] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Vehicle went into limp mode Twice. 1st time on 10/28/24, Technician found fault for Hybrid Battery pack, Chrysler technical service bulletin said to clear fault then drive, if fault did not come back release the vehicle Work order stated, Bring vehicle back if it happens again and replace hybrid battery. 2nd time, 2/06/2026 vehicle went into limp mode again while driving. My safety and the safety of others was put at risk as I was driving on a highway at 65 MPH and suddenly without warning and no braking involved...
Read the full complaint
went down to 20 MPH. A very unsafe maneuver as the following vehicles had no indication I was braking or Slowing down. The dealer has confirmed the limp mode incident but so far has been unable reproduce it. The vehicle and components have only been inspected by the dealer. The warning lamps and messages only came on as the event unfolded. A sudden and uncontrollable loss of power. The dealer states that they believe the hybrid battery pack is failing, but Chrysler, Stellantis will not replace the hybrid battery pack unless the dealer can reproduce the incident. Extremely dangerous thing to try and recreate.
The contact owned a 2018 Chrysler Pacifica. The contact stated that while in reverse(R) and reversing into a parking spot, it was difficult to accelerate over a patch of ice. The contact depressed the accelerator pedal, and the vehicle accelerated quickly and failed to stop while depressing the brake pedal and the vehicle drove through a fence and crashed into a brick building and stopped. The contact stated that prior to the failure, the U-Connect phone feature disconnected independently. The failure had never...
Read the full complaint
occurred before. The contact stated that the U-Connect failure might have been linked to the unintended acceleration failure. No injuries were sustained. A Police report was not filed. The fence and a side of the brick building were damaged during the crash. The vehicle was initially towed to the residence before being towed to a Collision Center, where the vehicle was deemed a total loss by the Insurance Provider. The vehicle was destroyed. The manufacturer was not notified of the failure. The failure mileage was approximately 159,000.
As I was leaving the gas station the Check engine light flashed on and off then the car was like turning on and off fast and a loud clunk sound and the Fuel pump module exploded gas sprayed all over the gas station. Huge fire hazard and the car began to smoke Vehicle experienced a sudden catastrophic fuel system failure involving fire risk and loss of propulsion. The incident occurred without warning and created a serious safety hazard to occupants and surrounding traffic. This vehicle is a Chrysler Pacifica...
Read the full complaint
Hybrid. Similar failures involving fuel system and hybrid control logic have been widely reported. The manufacturer was contacted but declined to properly document the safety incident. This failure is not consistent with normal wear and tear and represents a potential safety defect. Key details to include when submitting online: - Sudden loss of propulsion - Fire risk / fuel involvement - Hybrid system interaction - Manufacturer declined to document incident
Chrysler Pacifica transmission complaints by year
Pacifica transmission problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data