- The problem
- Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "Lamps, reflective devices, and associated equipment." These lamps do not contain the required amber side reflectors.
- The risk
- Decreased lighting visibility may result in a vehicle crash.
- The fix
- Sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589.
Lights
2003 Dodge Neon Lighting problems
Owners have filed 48 complaints about the 2003 Dodge Neon's lights with NHTSA - 24% of all its complaints, most recently on October 20, 2019. They describe 0 crashes, 7 fires and 0 injuries. Headlights, tail lights, brake lights, turn signals and interior lighting failures.
- Complaints
- 48
- Recalls
- 4
- Crashes
- 0
- Fires
- 7
- Injuries
- 0
- Deaths
- 0
Lighting recalls for the 2003 Dodge Neon
- The problem
- K2 motor is recalling 1,921 aftermarket headlamps of various models sold for use on the above listed vehicles. These headlamps are missing the amber side reflex reflector which fails to conform with the requirements of federal motor vehicle safety standard no. 108, "Lamps, reflective devices, and associated equipment."
- The risk
- Without the amber side reflex reflectors, the lighting visibility may be affected, possibly resulting in a vehicle crash.
- The fix
- K2 motor will notify owners and offer a full refund. The recall began on decemeber 17, 2008. Owners may contact k2 motor at 1-909-839-2992.
- The problem
- Certain ck motorsports combination headlights, clear corner, bumper, and side marker lights sold as replacement lamps for use on the passenger vehicles listed above. Some combination lamps that are not equipped with amber side reflectors fail to conform to federal motor vehicle safety standard no. 108, Lamps, reflective devices, and associated equipment.
- The risk
- Without the amber reflectors, the vehicle will be poorly illuminated, possibly resulting in a vehicle crash without warning.
- The fix
- Ck motorsport will notify owners and replace the noncompliant lamps free of charge. The recall began on july 1, 2006. Owners may contact ck motorsport at 1-909-610-7211.
- The problem
- Certain pro-a motors corner lamps, turn signals, and headlights sold as replacement lamps for use on certain passenger vehicles listed above. Some combination lamps that are not equipped with amber side reflectors fail to conform to federal motor vehicle safety standard no. 108, Lamps, reflective devices, and associated equipment.
- The risk
- Without the amber reflectors, the vehicle will be poorly illuminated, possibly resulting in a vehicle crash without warning.
- The fix
- Pro-a motors will notify owners and offer to repurchase the lamps. The recall began on april 3, 2006. Owners may contact pro-a motors at 323-838-2988.
Lighting complaints
This makes 3rd transmission that has been put in this 2003 dodge neon xst . I have put $10.000.00 In transmission replacements ! These are lemons!! I will never buy another dodge!!
Started vehicle during rainy, foggy, 40 degree weather. Headlamp indicator did not come on within gauge cluster. Upon checking outside the car, only parking lights were functioning despite headlights switch being in the "on" position. Burning smell occurred within 15 minutes of driving and multifunction harness connector is melted. *Tr
Smoke started coming out of the vents & steering column. Took it to the dealer & they said it was spilled anti freeze from when they changed the oil. Car was ok for a little while. Now it's smoking again the front defroster doesn't work the fog lights are gone & recently my highlights went too. I took it to the shop they shown me the burnt wires in steeling column & said the heating coil is damaged making the smell & fogs the window from the fumes. Next to go will be the turning signals & wipers if not fixed. *Tr
Started to see smoke and then the headlights stopped working properly. After disassembling the wiring connector from the headlight switch, I discovered the connector had overheated to the point it was charred and crumbling to pieces. This is not a misuse by operator, but a safety failure of the electrical system. This could have resulted in a fire as the fuse protecting this circuit did not fail when the circuit obviously overheated and melted and charred the plastic connector. *Tr
Smelled hot wiring and headlights stopped working properly. After disassembling the wiring connector from the headlight switch, I discovered the connector had overheated to the point it was charred and crumbling to pieces. This is not a misuse by operator, but a safety failure uf the electrical system. This could have resulted in a fire as the fuse protecting this circuit did not fail when the circuit obviously overheated and melted and charred the plastic connector. I have pictures of the part if you would like them. *Tr
My wire harness/ multifunction switch has melted causing my headlight and fog lights not to work. *Tr
Tl* the contact owns a 2003 dodge neon. The contact stated that the high beam headlight switch failed, which affected the fog lights. After performing research, the contact deduced that the wiring harness was melted and needed to be replaced. The dealer was later contacted and advised that he would have to bring the vehicle in for inspection. The contact repaired the vehicle by replacing the high low beam mechanism, but did not replace the wiring harness. The manufacturer was not contacted. The failure mileage was approximately 100,000. The current mileage was approximately 185,000. The vin was unavailable.
Headlights went out while driving at night then would only operate intermittently until finally they didn't work at all. Took off the multifunction switch and the electrical connector to the switch was melted. After some research I found out that the manufacturers made the wires too small to carry the electrical load. *Tr
First the fog lights would turn on and off randomly when the headlights were on. Upon inspection of the multi-function switch, I noticed a portion of the plug had melted from extreme heat. Most likely due to a poor design in the wiring, the circuits or the multi-function switch. Had this been left unnoticed it could easily result in extensive damages, fire or personal harm.
I have been having problem with my car for about 6 months. One of the problems were my high beams will operate but my low beams wouldn't. Now my high beams will operate but I am unable to switch to my low beams. The second problem is with my battery dying several times which resulted in getting a jump from another car. I end up having a battery and alternator replaced on my car last year between nov/dec 2010. Just recently I noticed smoke coming from my steering column located near the steering wheel and the...
Read the full complaint
smell of something burning. This happen while I was driving. My car didn't start monday 3-28-11 morning so I had it towed to the dealership where I bought the car from. The mechanic had to replace the battery. They ran a diagnostic on the car but no readings regarding electrical problems. The important question pertains to what is draining the battery. *Tr
Just driving one day evening, about 1.5 Hours onto the trip I start to smell something wierd and a few minuets later my headlights start to flicker and then they shutoff. I pulled over and checked the fuses, they were all good. I had to stay in a nearby hotel that night. The next morning I looked at an online forum for a solution and found one that suggested that the harness melts. I pulled off the sterring colum and to find the connector into the multifunction switch has completly melted. I bought a new harness and switch and installed myself. The forum said that to keep the headlights off as much as possible to not let the wires get too hot. *Tr
While the headlights are on and signaling for a right turn the fog lights come on the entire time it was in that position. This happens every time now although the fog light switch is in the off position. While trying to find the source of the problem I noticed that movement of the turn signal stalk in a circular motion also turned on the fog lights briefly. *Tr
My 2003 dodge neon srt4 started smoking from the steering wheel column, and my head lights went out, also my brake lights and dash lights went out as well. When I took it to the mechanic after checking they saw that the connector from the multifunction switch was all melted and had caught on fire thank god it didn't spread at the time. I had to replace the whole harness and switch and from forums I have come to know that there is a lot this cars with same problem. This has to stop is really dangerous and is costing us a lot of money, it is really unsafe. *Tr
The problems first started when the fog lights on my 2003 dodge neon had started to come on even when the switch was off. They would do this any time I turned the wheel, or went over a bump. This had been going on for almost 6 months. Then about a week ago, my lights would not turn off. The lever wouldn't click when I hit it to turn them off. They continued to stay on, and then would turn off when they wanted to. After about a day I was driving home at night, and all of a sudden my lights turned off, and would not go back on. If there were no street lights, I could have gotten into a severe accident. *Tr
Multifunction headlight switch failure, smell of burning plastic followed by failure of low beam headlights, pulled on high beams and exited interstate. Found pin plug and switch were melted. Replace switch and wiring plug. *Tr
The fog light switch stopped working, therefore the fog lights were always on. After stopping at a friends house and the lights worked fine, the headlights and fog lights would not turn on, and the bright lights could only be turned on by pulling and holding the arm back. There was an odd smell, but I thought a fuse must have blown. Changing the fuse did not allow the lights to work. I drove the car home behind our other vehicle, and was stopped by the police with no headlights. I explained the situation and...
Read the full complaint
they gave me a warning to have the lights fixed. So I made an appointment the next day to have the lights checked. They found the multi function switch was melted and the wiring harness had to be replaced. I am concerned that this could have happened to my wife with children in the car. No headlights driving at night. *Tr
I was getting ready to drive to work. I turned on my headlights to find that they were not functioning. Later I removed the multi-function switch and located a burned electrical connector. The current repair will be to replace the multi-switch and burned connector. *Tr
Driving at night, headlights wouldn't switch to low, then headlights ceased working at all, extremely hot, electrical smell, multifunction switch melted, needed to be replaced. *Tr
About 6 months ago while driving to work, it started raining and I turned my headlights on. The headlights would not come on but the driving lights did, I flip the headlight switch up to high beams and the brights worked. I noticed in the process that smoke started coming from steering column and it smelled like wires burning. While driving on the interstate, after it had rained. I set my cruise control, the first time, used it since the smoke. I set the cruise at 75 mph. The car started accelerating to 80 the...
Read the full complaint
computer caught the increase and downshifted on it's own. About 10 minutes later, the car started accelerating again, this time it was up to 90 mph, and continuing to gain speed. I pressed the brakes and the cruise control button to release the cruise and neither worked. I was coming up on the exit that I was needing to take. I down shifted the automatic to 2nd and 1st the car slowed, but not enough. I shifted to neutral and still the car would not stop. At the bottom of the exit ramp there was a wide spot that I knew that I could use if a car was coming. At the bottom of the exit ramp I was finally down to 30 mph but still not able to stop. I finally pulled the emergency brake, still the car would not stop. Finally when the car was headed up a hill the car slowed to 10 mph and I shifted the car into park and turned it off. Finally, I stopped without any damage to the outside of the car, and with out leaving the road. The brakes have been replaced since the smoke and headlights have not worked on dim. The dodge place, dalton, ga is says that the multi functional switch that control the headlight will fix the problem that caused the cruise control to lockup that is on a different control. How many lives have to be injured or lost before chrysler issues a recall for their cars. I had my 8 & 10 yr olds with me earlier, and had just dropped them off. Is fixing your parts that are installed on cars by manufacturers worth more than 3+ lives. *Tr
December 2008, headlights working fine during trip, stopped for gas, and headlights would not come back on. Used high beams for about 20 minutes and then switched to low beams were then working. Happened at least once a month for the next year. Early march, noticed a burning smell, thought it was outside, lights were working fine. While driving alone at night april 2009, tried to use high beams, but multifunction switch would not stay in place, had to hold the switch back for high beams to work. My hands...
Read the full complaint
became very warm sitting on the steering wheel, felt closer to the steering column and was incredibly hot. There was nowhere to stop, had to keep driving another hour or so. Stopped for 5 minutes and shut off vehicle, when vehicle turned back on, headlights wouldn't work. Had to drive with only parking lights at 2am, very unsafe! Ever since, headlights no longer work. This has clearly been an issue, and it very easy to find information and other complaints about this same problem. This could have clearly become an even worse problem. Tried to replace the multifunction switch, but the plug was melted in place. Parts were burned black and brown and incredibly brittle from the intense heat that emanated from the wiring. This final problem happened at about 90,000 miles. I am still currently waiting to find the large sum of money to get this fixed. I am currently not able to drive at night , since I do not have proper lighting. Afraid to even use parking lights, as this supplies electrical juice to the switch and could possibly cause a fire, as I have read about other owner's problems. *Tr
My headlights and foglights would periodically shut off or not come on. Then only the brights would work and while driving would shut off altogether. Finally the headlights and foglights have stopped working. The marker lights and turn signals still work, but I have no illumination ahead of me. It required a switch and connector change. So far there are numerous other neons that have had this happen to them and the dealer refuses to help us in any way, shape, or form. The old parts are still available for examination and the oem bulbs are still around as well. *Tr
My 2003 dodge neon srt-4 was making a funny smell at night then my lights went out and they would only work with my bright switch pulled back. I pulled apart and saw that my switch to my multifunction switch was burnt. I went to dodge and they told me it was not covered under warranty. So I bought a new multifunction switch and plug. I do have all the old parts. *Tr
2003 Dodge neon, low beams quit working a few weeks later the fog lights became intermittent, then eventually quit working too. Upon examination it was discovered that the connector that attaches to the multifunction switch is melting from being overheated during headlamp/foglamp use. Dodge is aware of the problem but does not have a recall on it. A repair kit is available, the description for which clearly indicates that dodge is aware of the problem. Research also reveals that the same repair kit is indicated for several other chrysler products exhibiting similar design deficiencies. *Tr
When I use my headlights for 15-20 minutes, I begin to smell a burnt plastic smell and notice the left side of the steering wheel gets very warm. After 20-30 minutes of headlight use the low beams just go dead, it "automatically" switches to high beams immediately. If I try to turn it back down to low beams, everything goes dark (*very* dangerous at night!). Then I am forced to use high beams and blind everyone else for the rest of my trip, or I have to pull over and let the apparent cause (the multifunction...
Read the full complaint
switch) cool off for an eternity before resuming my trip. I'm highly uncomfortable knowing that my car has plastic behind the steering wheel on the verge of erupting into flames when I use my headlights. I also consider it extremely hazardous, not only for the fire risk, but also the low beams dying suddenly. *Tr
Wiring melted in steering column and head lights would not work. Had to have dealer repair wiring, replace headlight switch. *Tr
Dodge Neon lighting complaints by year
Neon lighting problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data