Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer...
Transmission & drivetrain
Ford Bronco Transmission problems by year
136 complaints filed with NHTSA about the Ford Bronco's transmission & drivetrain. Harsh or delayed shifting, slipping, CVT shudder, rollaway, axles, driveshafts and transfer cases.
Transmission complaints by model year
Transmission recalls
Ford Motor Company (Ford) is recalling certain 2024-2025 F-150, Bronco, 2024 Ranger, 2025 Mustang, Explorer, and Aviator vehicles. The transmission valve body may have been machined incorrectly, which can cause reverse gear failure, or unexpected forward...
Ford Motor Company (Ford) is recalling certain 2023 Bronco vehicles. The transmission park system may have been damaged during assembly, which can prevent the parking pawl from fully engaging and result in a vehicle rollaway.
Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging...
The transfer cases have been built with the wrong electric shift motor. The transfer cases can slip out of the 4 x 4 high gear position during coasting in forward gears or with power applied in reverse gear.
The parking pawl actuating rod in the transmission may have an insufficient or cracked weld. This can cause the park cam end to separate from the rod itself, preventing the parking pawl from engaging the parking gear when the selector is placed in the park...
The involved vehicles may have been produced with rear axle shafts (right or left) that did not receive proper heat treatment of the bearing journals.
The involved vehicles were equipped with automatic transmissions in which the parking pawl was not heat-treated. During normal vehicle operation, a parking pawl that has not been heat-treated could become deformed or worn to the point that the transmission...
These transmissions may contain improperly manufactured parking pawl actuating rods. Consequently, the unhardened cam surface of these rods can allow the rod to deform during use with resultant increase in shift efforts and difficulty in releasing the parking...
Some of these vehicles may be equipped with automatic transmissions that were assembled with improperly manufactured cast iron extension housings. The housings have mislocated cast cam plate stops. A mislocated stop may prevent the transmission from locking...
The shift selector reaction springs may be deformed as a result of improper installation of selector levers during column buildup. Thus the lever may not be able to be moved into the insert detents located in the steering column assembly. This could prevent...
On the involved vehicles, the park actuation support plates are defective due to their susceptibility to cracking due to improper heat treatment during manufacture. As a result, fragments from a broken plate can become lodged in the transmission parking pawl...
Latest Bronco transmission complaints
The contact owns a 2024 Ford Bronco. The contact stated that upon shifting into park, and exiting the vehicle, the vehicle unintendedly rolled backwards and crashed into a parked vehicle. The contact's 80-year-old father was seated in the front passenger's seat during the failure. The contact stated that while attempting to catch up with the vehicle, the right hand middle finger was injured. The contact sought medical attention and received seven stitches. The manufacturer was contacted by phone, and a case was filed. The contact was informed that the VIN was not included in NHTSA Campaign Number: 26V236000 (Power Train). The failure mileage was approximately 15,000.
On October 15, 2026 I was driving my 2024 Ford Bronco Raptor home on I-285 near [location]. The vehicle stalled completely and would not hold speed at any speed from 35 to 78 mph. While exiting the ramp it stalled and I was nearly rear-ended. The trip normally takes up to two hours and took about three. The day before, about 150 miles from home, the vehicle was skipping, stalling and making an unusual noise, and passengers said the transmission was slipping. The same problem began at about 20,000 miles. The dealer...
Read the full complaint
repaired the transmission in July 2026 at 24,075 miles. It returned within about 500 miles. The dealer could not duplicate it in September 2026. In October 2026 the dealer confirmed the problem and replaced the torque converter. The odometer read 26,423 miles on October 29, 2026. There was no crash or injury, but this was a near collision at highway speed. Ford case numbers: CXH-08566342-K5D9F1 and CXH-09640578-G1Z5H1.
I have a 2024 ford bronco 2.3 with a manual transmission 13256 miles .This Saturday we left early in the morning to go to flagstaff. We got on the freeway about to 60 and go in to 6th gear pushed clutch in and it stuck to the floor tryed pull it up and did come back up had a horrible smell and than stop moving could not put in gear and coated off the freeway shut car off let it sit for 5 minutes and started back up put in first gear did not move called road side and was told I could get it towed to the dealership...
Read the full complaint
and if it covered under warranty they reimburse me for the tow . I said so your leaving us stranded on the freeway with a car thet should be towed in under worenty this is not safe . 1.5 hours later the tow guy came and was towed to the [[redacted]] ford which I had [[redacted]] as my service writer she asked if maby we left the emergency brake on because of the smell than said there is an open recall that need repaired well I like to get the [[redacted]] to move forward or revers told her the clutch pedal went to the floor and did not come back up and in my experience the hydraulic system in the clutch went out and may have wiped out the clutch I let her know we have 3 cars at home thet are all manual transmission all v8 fro 5000 miles to 105 and never have I had a clutch problem but she had to get the well this is a were and tair idem and you may have to pay for the repair this is the problem shit product and you say it's bumpers to bumper but they want to charg you any way they can my advice stop bying fords I know this will be are last one ever what a horrible experance and not a peace of mind at all also like all their adversaries say built solid like a rock them should say if you hit a rock your worinty is void INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
My 2024 Ford Bronco repeatedly loses power without warning while driving, including on highways, suddenly slowing to approximately 32 mph. It also fails to accelerate from traffic lights, leaving me stranded in traffic. Dashboard warnings include Powertrain Malfunction, Service AdvanceTrac, Check 4x4, and Pre-Collision Assist Unavailable. On September 30, 2026, at 9:43 PM, the vehicle lost power on the road, nearly causing a rear-end collision. I have videos documenting six incidents between September 30 and...
Read the full complaint
October 15, 2026. This dangerous problem has continued since May 2025. Briarwood Ford has attempted repairs seven times, including replacing the accelerator pedal twice and replacing or repairing the engine wiring harness. The vehicle has been out of service for over 60 days, yet the problem continues. Ford diagnostic data from October 15-16 identified codes P2138, U0401, U0403, and U0418. I no longer trust this vehicle to transport my family to chemotherapy appointments or allow my children to drive it. Sudden power loss in traffic creates a serious risk of injury or death. I request an immediate NHTSA safety investigation into this recurring, unresolved defect.
Transmission failed while towing in Neutral Flat Tow mode and destroyed the entire transmission resulting in a $7,600 repair bill. Ford will not warranty this as they claim is was might fault. Not true, I had flat towed the vehicle for months without an issue and its their electronic system that failed and destroyed my transmission.
My vehicle has had two misfires and the check engine light came on twice. I brought it to quirk ford in Quincy mass and they said ford has not found a solution for this recall which has been years for this recall. My vehicle putters when I start it and has a skunk aroma when I shut it off
We sometime have loss of drive power while driving or a total failure to engage a gear. Happens sometimes when moving from a stop sign or stop light. Like the transmission is slipping in def case.
Clutch pedal went to floor and didn't return. The accumulator on part # MB3Z-7A512-A failed and broke apart causing a complete loss of brake fluid in the clutch hydraulic system rendering the clutch completely inoperable.
Persistent highway-speed vibration (45 to 82 mph) present since July 2022, documented at five Ford dealerships between 21,000 and 100,000 miles, and still unresolved and undiagnosed after four years. It is a whole-vehicle shake felt primarily through the seat and from the rear of the vehicle at highway speed, occurring on highways nationwide (documented in [[redacted]], [[redacted]], and [[redacted]]). Wheel and tire causes were controlled for and eliminated: three complete wheel-and-tire set swaps (two on factory...
Read the full complaint
stock sets) did not change the vibration; a dealer road-force balance (08/2024) did not resolve it; it persists while coasting in neutral. On [redacted] an independent facility (Heritage Auto Solutions, [[redacted]]) road-tested and lift-inspected the vehicle and identified objective anomalies at the rear driveshaft: an abnormal welded balance-weight cluster and visible play at the slip yoke; the facility recommended replacement. The shaft is currently at an independent driveline facility for balance testing; the root cause of the vibration has NOT been definitively confirmed by any facility. That is the safety concern: a sustained, unresolved vibration consistent with a driveline-area defect at 70+ mph, present for four years, with no dealer ever performing an instrumented driveline diagnosis. A driveline component failing at highway speed is a loss-of-control hazard. Ford has issued driveline field actions on this platform (Customer Satisfaction Program 22B27, front driveshaft, noise/vibration; Recall 26V236, transfer-case misalignment, possible loss of drive power). The manufacturer was formally notified in writing of the independent findings on [redacted] (Ford case [redacted]) and has not responded as of [redacted]. Attached: the independent facility's written report and driveshaft photographs. The vehicle is currently out of service. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
2023 Ford Bronco with 7 speed manual transmission. The transmission started grinding while shifting into 3rd gear and occasionally popping out of 3rd gear. This mostly occurred while upshifting and rarely while downshifting. All other gears are operating as normal. While the grinding problem would pop up occasionally around the 40,000 mile mark, it became chronic at 58,000 mile mark (24Jun2026)
2022 Ford Bronco 2.7L EcoBoost VIN [[redacted]] has experienced recurring engine oil pressure failure causing vehicle to enter limp mode limiting speed to 25mph creating an unsafe driving condition. Diagnostic trouble codes P0524 Engine Oil Pressure Too Low and P06DD Engine Oil Pressure Control Stuck Off confirmed. Two failed warranty repair attempts at Lenoir City Ford Lenoir City TN on [redacted] and [redacted]. Dealership provided loaner vehicle both times acknowledging vehicle was unsafe to drive. Ford corporate case number XXC is open. Third repair attempt scheduled [redacted]." INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The Incident: While operating the vehicle under high load, the driver received an explicit "Service Engine Soon" powertrain malfunction alert stating: "The powertrain control module lost communication with the vehicle active grill shutter module for a period of time." Immediately following this warning, the engine experienced a severe loss of power, followed by loud metallic banging from the engine bay. The vehicle stalled completely and lost all motive power, creating an imminent highway safety hazard.The Physical...
Read the full complaint
Damage: Subsequent mechanical teardown by the dealership revealed terminal block destruction, including deep vertical cylinder wall scoring, heavy unburnt liquid gasoline residue in the engine oil pan, and a blown head gasket.Relationship to Active Safety Defect: This catastrophic engine failure mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). In this EcoBoost architecture, the Active Grill Shutter (AGS) module shares critical voltage paths, grounding blocks, and wiring looms with the engine management and fuel delivery systems. The sudden network communication loss is diagnostic proof of a severe voltage drop or electrical short caused by the high-friction fuel pump degradation detailed in Recall 25S75. This circuit failure instantly starved the engine of fuel under turbo boost, inducing an extreme lean-out condition. The resulting pre-ignition forces violently shattered the internal piston rings (the loud banging), which then gouged the cylinder walls, wiped out compression, fouled the crankcase with fuel residue, and blew the head gasket.Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as definitive evidence of consequential engine destruction originating from the 25V455 fue
While operating the vehicle under load, the vehicle suffered a sudden and severe loss of engine performance, followed immediately by loud metallic banging from the engine bay. The vehicle lost all power and was immediately disabled (LIMP MODE), presenting an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown revealed deep vertical cylinder wall scoring, heavy raw fuel residue in the engine oil pan, and a blown head gasket. Relationship to Active Safety Defect: This catastrophic block...
Read the full complaint
failure perfectly mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). Internal component degradation in the fuel tank delivery module dropped fuel pressure to the engine. Under turbo boost, this starvation induced an extreme, instantaneous lean-out condition. The resulting low-speed pre-ignition (LSPI) exploded and shattered the internal piston rings (the metallic banging), leading to mechanical wall gouging, unburnt fuel wash into the lower crankcase, and a secondary blown head gasket. Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as clear evidence of consequential engine destruction originating from the 25V455 pump defect, and evaluate whether Ford's recall scope must be expanded to protect other consumers from highway engine failures.
Differential carrier replacement due to metal contmination being found in differential during oil change and a transmission overhaul due to excessive wear of(clutch container, CDF bushing, forward hub and front support bushings). They also noted a sticking valve in the main control on my 2022 Ford Bronco 2.7L V6 when taken in to dealership to evaluate vehichle under warranty due to ongoing intermittent thump/clunking noise when coming to a stop and accelerating from a stop as well as when backing up from a stop...
Read the full complaint
and while driving as well, intermittent loud metal slapping sound at speeds over 60 mph, intermittent jerking of vehichle when cycling through gears, unexpected downshift at high speeds. After differential replacement and transmission overhaul due to excessive wear while under warranty, my vehichle continues to experience the same symptoms and problems and feel this is a safety issue.
My drive shaft/coupling caught fire at the front transfer case. I was able to extinguish it safely. This is the same description as: NHTSA Recall No.: 26V236 Manufacturer Recall No.: 26S26 And the description " Vehicle 1: 2021-2025 FORD BRONCO' includes my vehicle, however, my VIN/license plate number do not show this recall in effect.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data