Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Engine & cooling

2005 Ford Crown Victoria Engine problems

Owners have filed 11 complaints about the 2005 Ford Crown Victoria's engine & cooling with NHTSA - 6% of all its complaints, most recently on January 19, 2022. They describe 1 crash, 1 fire and 2 injuries. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.

Complaints
11
Recalls
0
Crashes
1
Fires
1
Injuries
2
Deaths
1

Engine complaints

Body, doors & structureWheels & tiresEngine & cooling

Unknown the ride feels unsafe to travel around inn

Filed Incident Structure · Wheels · EngineNHTSA 11447986
Transmission & drivetrainEngine & cooling

Loss of acceleration at wide open throttle, transmission seems to "slip" when trying to pass or accelerate hard at highway speed has happened on multiple occasions

Filed Incident Power train · EngineNHTSA 11000031
Engine & coolingFire

The spark plugs have been ejecting themselves from the engine, taking part of the cylinder head with them making repairs dangerous and costly. Sometimes the spark plug stays attached to the coil, causing fuel vapors to ignote, but most of the time they rip the coil pack and boot out with them. This has happened four times with my last crown victoria and twice with my current one. It always happens as the vehicle has been driving down the road, causing a dramatic loss of power and sometimes a fire.

Filed Incident EngineNHTSA 10854188
Engine & cooling

Tl* the contact owns a 2005 ford crown victoria. While driving approximately 65 mph, the vehicle stalled without warning. The vehicle was restarted. The contact discovered that the serpentine belt failed and was replaced. The failure recurred. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 104,000.

Filed Incident EngineNHTSA 10788531
Engine & cooling

At first the car would slip into neutral instead of going into 2nd gear so I had to turn od off now the car want go into drive at all. I see on the internet that this has a lot of complaints. *Tr

Filed Incident EngineNHTSA 10680455
SteeringEngine & cooling

I was responding as a volunteer ambulance emt from my residence to the fire station for an emergency call when the steering locked up. I tried to turn the steering wheel back and forth while applying the brakes and it began to steer again. I continued to the station about 3/4 mile away, made the ambulance call. Upon completion of the call I lifted the hood and observed the lower joints of the steering shaft were rusty and corroded. I sprayed the joint with wd-40 and turned the steering back and forth. In...

Read the full complaint

preparation for a trip two days later I was checking the vehicle and found the "exhaust heat shield" lying on the frame between the engine and frame. It was then I figured the part had come off and jammed between the steering shaft and the frame causing a momentary loss of steering control. I have not replaced the heat shield. After a factory recall replacement of the lower shaft resulted in the car steering like new with very little effort for a month or so. I then noticed the steering seemed to bind again at times. I looked and the upper steering shaft is corroded so I sprayed the u joint contained in the upper shaft with lubricant. I contacted the dealer who said the upper shaft was not part of the recall so I called ford and was told the same thing. The upper shaft joint is experiencing the same failure as the lower shaft. Corrosion in the u joint is causing the needle bearings to not operate properly resulting in more difficult turning of the steering. I lubricate the joint at times. I believe the "upper steering shaft" should be included in a recall due to corrosion effecting the parts due to design not sufficient to prevent contaminates from entering the steering u joints. The "exhaust heat shield" was deteriorated due to corrosion of the mounting holes used to secure the shield to the exhaust manifold mounting bolts. *Tr

Filed Incident Steering · EngineNHTSA 10615584
Transmission & drivetrainEngine & cooling

Tl* the contact owns a 2005 ford crown victoria. The contact stated while driving approximately 45 mph the wrench warning symbol illuminated and the engine stalled. Upon restarting the vehicle it failed to accelerate over 5 mph. The failure was repaired. The manufacturer was notified of the failure. The approximate failure mileage was 76,000. ..Updated 02-28-14 *bf updated 03/19/2014 *js

Filed Incident Power train · EngineNHTSA 10550461
Seats & seat beltsEngine & coolingCrash2 injuries1 death

My wife died in this police car lost control due to engine jerking and seat belts came loose and ejected my daughters havin head injury concussion and broken skull. *Tr

Filed Incident Seat belts · EngineNHTSA 10536369
Engine & coolingAcceleration & cruise control

Tl* the contact owns a 2005 ford crown victoria. The contact stated that the engine exhibited an abnormally excessive increase in rpm's. The contact stated that he would have to depress the brakes hard so that the vehicle would not run away. The vehicle was taken to the dealer where they were unable to duplicate the failure. The manufacturer was contacted but offered no assistance. The failure mileage was 33,000. Updated 8/30/11 *cn the consumer stated while at a stop, with the engine running, he experienced a...

Read the full complaint

high engine acceleration without touching the accelerator pedal and the brakes would hardly hold the car in place. The consumer stated he would have to shut the engine off. Updated 09/21/11

Filed Incident Engine and engine cooling · Vehicle speed controlNHTSA 10412404
Engine & cooling

Catalytic converter rattles after 54,000 miles found ford bulletin on problem. Should be replaced by ford. *Tr

Filed Incident Engine and engine coolingNHTSA 10358052
SteeringSuspensionEngine & coolingFuel systemLights

1995 Ford crown victoria [[redacted]] upper and lower ball joints needed to be replaced. Tie rod and pitman arm replaced. Gas tank leaks. Moisture on piston which threw a rod and broke block. Headlight lenses turned dark orange. *Js information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6)

Filed Incident Steering · Suspension · Engine and engine cooling · Fuel system, gasoline · Exterior lightingNHTSA 10121726

Ford Crown Victoria engine complaints by year

Crown Victoria engine problems, every year

Had a engine problem with your 2005 Crown Victoria? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience