Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Engine & cooling

2008 Kawasaki KLR650 Engine problems

Owners have filed 13 complaints about the 2008 Kawasaki KLR650's engine & cooling with NHTSA - 11% of all its complaints, most recently on June 18, 2012. They describe 0 crashes, 1 fire and 0 injuries. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.

Complaints
13
Recalls
0
Crashes
0
Fires
1
Injuries
0
Deaths
0

Engine complaints

Engine & cooling

The engine burns oil excessively at highway speeds (60 to 70 mph). An engine lockup due to lack of lubricant is a very real concern due to the oil consumption rate. *Tr

Filed Incident EngineNHTSA 10462108
Engine & coolingTransmission & drivetrain

The starter idler gear shaft hole/sleeve is bore/milled to deep on the outside casing. The shaft moves to the casing side and loses contact with the inside bushing/sleeve, wich forms a gap at the main housing side. There is now enough space for the spacer washer to fall into the bottom-end and cause huge/catastrophic failure. *Tr

Filed Incident Engine and engine cooling · Power trainNHTSA 10434053
Engine & cooling

Tl*the contact owns a 2008 kawasaki klr650. While traveling 65 mph the contact noticed that the vehicle had suddenly shut off without warning. The vehicle was taken to the dealer where the contact was informed that the engine needed to be replaced due to oil leaks. The vehicle was not repaired and there were no prior warnings. The current and failure mileages were 5400.

Filed Incident Engine and engine coolingNHTSA 10349235
Engine & cooling

2008 Kawasaki klr 650 starter gear cover is improperly bored allowing support shaft to become unsupported on one end. This could cause thrust washers to drop into the rotating flywheel at speed, locking the motor and causing loss of control. Older and newer models both have a ridge in the outer engine cover that prevents the idler gear shaft from drifting out too far and loosing support in the inner engine cover. This was clearly a machining error. I inserted a small spacer in the hole to prevent the shaft from moving. *Tr

Filed Incident Engine and engine coolingNHTSA 10334914
Engine & cooling

The safety issue is on a 2008 kawasaki klr-650. The started gear is grinding when I try to crank the bike. The dealer will not fix the issue. The cause of the failure is a deep bore on the side cover that holds the gear. It is a mfg issue. My concern is when the gear lock up? There is a good chance it could lock up as I'm riding down the rode. *Tr

Filed Incident Engine and engine coolingNHTSA 10334707
Engine & coolingFire

Cover side hole that lower starter gear pin rides in is milled too deep and can result in severe engine damage. While installing a balancer tension spring upgrade (another issue with these motorcycles) I found I had this issue. I had to install a spacer to fix and prevent the other side from coming out of engine side hole and causing damage. *Tr

Filed Incident Engine and engine coolingNHTSA 10334646
Engine & cooling

The starter gear shaft can migrate out in the left side engine cover, leaving the gear unsupported on the inboard side and allowing a washer to migrate loose into the engine--potentially causing the transmission to lock up or the timing chain to skip teeth and cause the intake or exhaust valves to hit the piston top, bending valves and making the engine inoperable. *Tr

Filed Incident Engine and engine coolingNHTSA 10334599
Engine & coolingElectrical system

2008 Kawasaki klr 650 motorcycle. Consumer states several problems with motorcycle and has received recalls *tgw since purchasing the motorcycle, the consumer had to replace three batteries. While changing the oil for the first time, he discovered the engine was consuming eight to ten ounces of oil per thousand miles of use. The consumer contacted the manufacturer and was informed the oil consumption fell within the acceptable range as specified by kawasaki engineers. The consumer believed the pistons were too small for the cylinder bore on his bike. *Jb

Filed Incident Engine and engine cooling · Electrical systemNHTSA 10329636
Engine & cooling

2008 Kawasaki klr 650 engine uses an abnormal amount of oil, leading to engine seizure/failure/costly damage. *Tr

Filed Incident Engine and engine coolingNHTSA 10313024
Engine & cooling

Tl*the contact owns a 2008 kawasaki klr650. The contact received a recall notice for nhtsa campaign id number 09v059000 (engine and engine cooling:exhaust system:manifold/header/muffler/tail pipe) and immediately called the dealer. The dealer stated that the vehicle should not be driven because the bolts could loosen completely and the muffler could possibly separate from the vehicle, causing a crash or serious injury. The dealer also stated that they would not pay for towing. The contact does not want to have the vehicle repaired if he has to pay for towing. The vehicle has not yet been repaired. The failure and current mileages were 2,500.

Filed Incident Engine and engine coolingNHTSA 10260428
Engine & cooling

The conditions herein may cause an engine failure. This failure could cause the engine to seize which could cause the loss of control of the vehicle [motorcycle]. The vehicle was in use under normal "street" conditions. High oil consumption due to manufacturing defect/ workmanship. 1 Quart+ of oil per 300 miles, resulting in high air pollution & possible engine seizure---from the loss of oil! Piston rings leak oil. There is also a groove in engine's cylinder wall [3"l x 5/32"w x 1/64"d] due to improper...

Read the full complaint

part assembly [piston's wrist pin clip; a factory defect]. The engine's exhaust valves leak which also produces poor air quality control. These conditions are internal to the engine and were created during the manufacturing process. These failures can only be determined through the disassembly of the engine. The above vehicle's has only been used for 2,085 [2k] miles. It is a 2008 model year. The above engine fails to meet air quality standards. The cost of repair is being estimated between $800-1000. This encompasses partial vehicle disassemble, upper engine disassemble, machine shop work, replacement parts, engine reassemble, and the reassemble of the area around the engine [it's a motorcycle]. To correct the above failures new parts must be installed along with necessary machining of engine's cylinder. *Tr

Filed Incident Engine and engine coolingNHTSA 10247179
Engine & cooling

2008 Kawasaki klr-650 motorcycle. Muffler fell off wile riding down the road with only 3,000k on odometer. All 3 mounting bolts fell out. This was a recall for other klr bikes. My bike was not recalled. One of the mounting bolts welded nut fell off also. Dealer gave me new bolts, I replaced one bolt with a locking crown nut and cotter pin. *Tr

Filed Incident Engine and engine coolingNHTSA 10238146
Engine & cooling

2008 Kawasaki klr 650 burning oil. Kawasaki replied to me, "if your motorcycle is burning a quart every 1,000 miles or less, that is normal." *Tr

Filed Incident Engine and engine coolingNHTSA 10225312

Kawasaki KLR650 engine complaints by year

KLR650 engine problems, every year

Had a engine problem with your 2008 KLR650? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience