Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Engine & cooling

Kawasaki KLR650 Engine problems by year

68 complaints filed with NHTSA about the Kawasaki KLR650's engine & cooling. Stalling, loss of power, oil consumption, overheating, head gaskets, timing chains and engine failure.

Engine complaints by model year

YearEngine complaintsCrashesInjuriesRecalls
20241000
20231000
20221000
20093000
200813000
20061000
20035000
20028000
200115000
20007000
19997000
19984000
19971000
19931000

Latest KLR650 engine complaints

2024 Kawasaki KLR650BrakesEngine & cooling

The contact owns a 2024 Kawasaki KLR650. The contact stated that while riding approximately 2-3 MPH, the ABS engaged independently. The contact stated that there was an ABS module failure as well. No warning light was illuminated. The contact stated that the motorcycle downshifted unexpectedly without the clutch being activated. An independent mechanic was contacted. The contact exited the motorcycle and walked the motorcycle to the closest shop. The motorcycle was taken to an independent mechanic, where it was...

Read the full complaint

diagnosed, and determined that the brake fluid needed to be changed. The contact stated that the failure reoccurred. The manufacturer was not notified of the failure. The approximate failure mileage was 86,000.

Filed Incident Service brakes, hydraulic · EngineNHTSA 11694562
2023 Kawasaki KLR650SteeringTransmission & drivetrainEngine & cooling

Steering bearing overtorqued by factory, dealer warranty loostened and readjusted, initial tendency, failure to return to neutral, rough bearing feeling, caused many near misses with vehicles ahead, problem unresolved, I can feel it, dealer can not. Contra Costa Powersports, 1150 Concord Ave Ste 100, Concord, CA 94520 (925) 687-7742. Issue regarding drive train, false neutral. Potentially hazardous conditions occurred three times. Pulled over to adjust GPS, engine running, shifted to neutral, neutral light...

Read the full complaint

illuminated on dash, put the side stand down,, released the clutch bike still in gear, bike lunged forward, off of sidestand, bike headed for ground with rider, lucky first two times I had my hand on the front brake, lock up brake preventing bike from launching off the side stand and crashing to ground. First time with stock clutch and brake levers set up by dealer with 1/16 clutch free play, third time with Warp9 aftermarket adjustable brake and clutch levers, was in same 1/16" free play when set up, cable seated during 100 mile ride, gap then 1/4", third false neutral, dash displayed green neutral indication light, side stand down, released clutch, bike still in gear, this time hand not on brake lever, didn't anticipate bike movement, the bike launched forward off the sidestand, tried to eject me into the roadway. Could have been lethal consequences had I not recovered the bike before it dropped to the roadway, I just managed to get it back up and out of the roadway before cars came around the blind mountain turn. The Clutch lever being slightly out of adjustment had no impact on shifting gears, and didn't miss one gear change. Stock clutch lever or Warp9 aftermarket, clutch freeplay 1/16 to 1/4 made no difference. I can not replicate the hazard, it occurred randomly. Technically, weather the neutral light illuminates on the dash or not, in gear, deploying the side stand should kill the bike. Dealer can not duplicate what to we do now?

Filed Incident Steering · Power train · EngineNHTSA 11582029
2001 Kawasaki KLR650Engine & cooling

Cam chain adjuster otherwise know as a doohickey. If it fails it may cause the engine to seize up without warning, I change mine after it broke but did not cause massive internal damage I was unaware that mine had failed I did the change as preventative maintenance this problem has been known to the klr community for many years but kawasaki refuses to recognize it, do a google search on doohickey for more info

Filed Incident EngineNHTSA 10926349
2009 Kawasaki KLR650Body, doors & structureEngine & cooling

This `09 klr 650 was purchased used from guy who bought it new having approx. 8000 Mi. My biggest complaint is possibly due to engine mounting and vibration whereas found exhaust manifold clamp had vibrated loose and detached from engine exhaust port. Another time found one of the side frame bolts had sheered or otherwise broke due vibration or defective material. Other similar problems involved having to replace or fix speedo cable and the protective leg / heat exhaust shield due to material or vibration issues.

Filed Incident Structure · EngineNHTSA 10811996
2009 Kawasaki KLR650Engine & cooling

Tl* the contact owns a 2009 kawasaki klr650. The contact stated that while driving at 30 mph, the motorcycle stalled without warning. The failure occurred on multiple occasions. The motorcycle was taken to the dealer where it was diagnosed that the wiring harness needed to be replaced. The motorcycle was not repaired. The manufacturer was notified of the failure. The failure mileage was 3,000.

Filed Incident EngineNHTSA 10667231
2009 Kawasaki KLR650Engine & cooling

This complaint does not represent an incident with my personal vehicle. The kawasaki klr650 series, all models spanning all mfg years, suffer from a weak chain tensioner assembly for the counterbalance shafts. This is an internal engine component. On the internet, this assembly is referred to as the "doohickey." Searching the web for "klr doohickey" will yield literally thousands of results of both fixes and failures. Kawasaki has never corrected the issue, and an industry has even emerged with aftermarket...

Read the full complaint

parts to correct the defect that the manufacturer has failed to address. This is a serious safety defect with the vehicle, as failure of the assembly has sent metal fragments through the engine and has potential to rapidly seize the engine. When traveling at speed, this can cause sudden loss of power, or even an unexpected rear wheel lockup on the motorcycle, either of which can be deadly. There are tens of thousands of these motorcycles on the road, yet only the enthusiast community is aware of the issue, and I fear there are many owners who are unaware of the risks. I would like nhtsa to investigate for potential recall. Thank you for your time. *Tr

Filed Incident EngineNHTSA 10628440
2000 Kawasaki KLR650Engine & cooling

The torsion spring on my klr 650 failed. This is a major problem and happens to alot of klr 650 owners. Lucky for me it didn't cause the engine to seize while I was riding. *Tr

Filed Incident EngineNHTSA 10562606
1997 Kawasaki KLR650Engine & cooling

I just wished to report something I found out by chance, upon inspecting the inside of my engine, and which could have potentially cause my engine to stop functioning/seize at speed, which in turn would have led me to crash. The idler shaft lever & spring in my engine was defective. Upon finding the broken part I went "fishing" for the missing pieces on the bottom of my engine using a magnet, and found another broken spring! My take is that the dealership had replaced the broken spring once already.. Which is...

Read the full complaint

why I believe there is defect issue with this part that should be addressed. Note that the broken part moving freely inside my engine could have easily cause damage getting tangled somewhere, for example in my transmission gears.. This could easily have been a horror story. Here are pics I took of my actual broken parts as they were in the engine, and after removal (with the additional broken spring I found..): Pic 1: http://i97.Photobucket.Com/albums/l229/katoner/2012-12-05_14-31-39_774.Jpg pic 2: http://i97.Photobucket.Com/albums/l229/katoner/2012-12-05_18-38-36_487.Jpg thank you for your attention and I hope this can help others. [[redacted]] information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr

Filed Incident EngineNHTSA 10487513
2008 Kawasaki KLR650Engine & cooling

The engine burns oil excessively at highway speeds (60 to 70 mph). An engine lockup due to lack of lubricant is a very real concern due to the oil consumption rate. *Tr

Filed Incident EngineNHTSA 10462108
2001 Kawasaki KLR650Engine & cooling

The idler shaft lever (aka "doohickey") broke in half and the pieces of it were floating around in the crank cased. This is very dangerous because if a piece of the idler shaft lever gets caught in the counterbalance chain or causes a crank bearing failure the engine could lock up at speed causing a crash. I replaced the idler shaft lever with a stronger aftermarket component. *Tr

Filed Incident Engine and engine coolingNHTSA 10454281
2008 Kawasaki KLR650Engine & coolingTransmission & drivetrain

The starter idler gear shaft hole/sleeve is bore/milled to deep on the outside casing. The shaft moves to the casing side and loses contact with the inside bushing/sleeve, wich forms a gap at the main housing side. There is now enough space for the spacer washer to fall into the bottom-end and cause huge/catastrophic failure. *Tr

Filed Incident Engine and engine cooling · Power trainNHTSA 10434053
1999 Kawasaki KLR650Engine & cooling

The 1986-2007 kawasaki klr650 motorcycle's tensioning system for the engine balancer shaft drive chain is unreliable, and a failure could lead to sudden engine lock-up and loss of vehicle control, potentially resulting in injury or fatality. The most troublesome parts of the balancer drive adjusting system are the idler shaft lever, p/n 13168-1436 and the spring, 92144-1860. The balancer adjuster idler rides on an eccentric shaft p/n 39115-1077, and when the shaft rotates it changes how the tension idler...

Read the full complaint

relates to the balancer chain, allowing the chain to be tensioned. The recommended procedure for adjustment is for the user to loosen a screw that holds the idler shaft lever, allow the spring to pull the idler into its new position, and then retighten the screw. If the idler shaft lever fails the spring is inadequate to withstand the cyclic loading as the chain runs at engine speed, and will lead to failure of the spring and loss of tension in the chain. If the spring fails between service intervals but the system was properly tensioned to begin with, the chain will lose tension when the user loosens the adjusting screw. Also on higher mileage vehicles the spring can come off its attaching points as it becomes too long for the application, causing it to fall into the engine. In either case the failure can result in the balancer drive chain becoming effectively untensioned. The chain is free to come off its sprockets, or to bunch up around the crankshaft sprocket that drives it, or to sometimes catch on the drive sprocket and sometimes slip leading to rapid sprocket and chain wear creating metal debris inside the engine. If the chain becomes bunched up around the crankshaft sprocket it could lock up the engine and make the vehicle suddenly immobile and uncontrollable. *Tr

Filed Incident Engine and engine coolingNHTSA 10399440
2003 Kawasaki KLR650Engine & cooling

Klr650 engine idle lever adjuster spring failed sending metal fragments through out the engine that I had to fish out - very very common problem to the point that it is the first thing people do when they buy a klr of any year. *Tr

Filed Incident Engine and engine coolingNHTSA 10358886

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience