- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
- The risk
- Insufficient air volume can reduce braking performance and increase the risk of a crash.
- The fix
- Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
Vehicle safety record
2020 Kenworth T680 Problems, complaints & recalls
Owners have filed 8 complaints about the 2020 Kenworth T680 with NHTSA, most often about the transmission & drivetrain (5) and the brakes (2). It is covered by 8 recalls, the latest in February 2024 for the reservoir / tank. For comparison, the 2019 has 8 and the 2021 has 0.
NHTSA data checked
CAbout as many problems as a typical T680 year, for its age
#172 most complained-about 2020 vehicle
- Complaints
- 8
- Recalls
- 8
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Most common 2020 Kenworth T680 problems
Share of all 8 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2020 Kenworth T680 recalls 8
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that attach the steering arm to the steering knuckle may fail.
- The risk
- Fastener failure can result in a loss of steering control, increasing the risk of a crash or injury.
- The fix
- Dealers will replace and torque the steer arm fasteners, at no charge. Owner notification letters were mailed November 8, 2022. Owners may contact Kenworth customer service at 1-425-828-5888 and Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall are 22 PBB and 22 KWB.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2016-2022 Peterbilt 567, 579, 2021-2022 Peterbilt 536, 2017-2021 Kenworth T880, 2016-2022 Kenworth T680, 2018-2020 Kenworth T440, 2020 Kenworth T270, and 2021 Kenworth T280 vehicles. The methane detection system will not function if the system loses power.
- The risk
- The operator may be unaware of a system malfunction or the presence of excessive methane levels, increasing the risk of injury or fire.
- The fix
- Dealers will re-wire the warning alarm, free of charge. Owner notification letters were mailed December 1, 2022. Owners may contact Peterbilt customer service at 1-940-591-4220, and Kenworth customer service at 1-425-828-5888. PACCAR's numbers for this recall are 21KWH and 21PBN.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2016-2021 Kenworth T680 trucks equipped with a 2.1m Cab and WABCO 6S/6M ABS brake system with drum brakes. The brake systems were manufactured with a standard rear-brake ABS modulator valve instead of a quick release valve, which may exceed the intended service-brake release timing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
- The risk
- Longer than expected service-brake release timing may lengthen vehicle stopping distance, increasing the risk of a crash.
- The fix
- PACCAR will notify owners, and dealers will replace the standard rear-brake, ABS modulator valve with a quick release valve, free of charge. The recall began November 30, 2020. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 20KWD.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
- The risk
- If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
- The fix
- PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2020 Peterbilt 520 and 579 vehicles and Kenworth T680, T880 and W990 vehicles. The mirror glass may detach from the mirror carrier plate due to inadequate adhesion.
- The risk
- If the mirror glass detaches, the driver may have reduced visibility and the mirror glass will become a road hazard that may strike another vehicle or pedestrian, increasing the risk of a crash or injury.
- The fix
- PACCAR has notified owners, and dealers will inspect the upper mirror glass/mirror carrier, replacing it as necessary, free of charge. The recall began May 31, 2019. Kenworth owners may contact PACCAR customer service at 1-425-828-5888 and Peterbilt owners may call 1-940-591-4220. PACCAR's numbers for this recall is 19KWC and 19PBC.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 T680 and T880 tandem axle vehicles equipped with a parking brake on a single axle and certain models of automated manual transmissions. During cold temperatures, the signal from the park brake pressure switch to the transmission controller may be delayed possibly resulting in the vehicle moving unexpectedly.
- The risk
- Unexpected vehicle movement may increase the risk of a crash or injury.
- The fix
- PACCAR will notify owners and dealers will replace the park brake pressure switch, free of charge. PACCAR issued owners and interim notification on June 3, 2019. The recall began August 6, 2019. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 19KWB.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2020 Kenworth T680, T800, T880, W900 and W990 trucks. The rear axles may not contain oil.
- The risk
- Without lubricating oil, the bearings, hub and axle shafts may wear, resulting in the separation of a wheel end from the axle, increasing the risk of a crash.
- The fix
- Paccar will notify owners, and Kenworth dealers will inspect all of the rear axles for the presence of oil. If no oil is present, the wheels ends will be removed and the bearings, hub and axle shaft will be inspected for damage. If excessive wear or heat damage is evident, the components will be replaced, as necessary. Oil will then be added per the axle specifications. These repairs will be performed free of charge. The recall began April 16, 2019. Owners may contact Kenworth customer service at 1-425-828-5888. Paccar's number for this recall is 19KWA.
What owners say
2 people checked this vehicle in the last 30 days. Problems or none - your experience is exactly what the next buyer is looking for. Write it now
8 complaints about the 2020 Kenworth T680
Newest first, as filed with NHTSA by owners.
Right-hand shift stalk between the shifter and the transmission is causing the vehicle to become disabled while stopped and unable to go from forward to reverse. Also getting SPN 639 pop-up when communication has been lost between the engine control module (ECM) and SAE J1939 data link. The check engine light illuminates, and the ECM immediately logs the fault code. Have to depress brake pedal while stopped & cycle gear selector to get fault to clear to start engine . Message also displayed Transmission Fault Repair Required Find Service Center . Also had new spring clutch replaced in May of 2024. Truck has 525k miles on it .
The clutch Spring on these trucks have been failing heavily. We have a couple more of these trucks and they all have the same issue. the housing for the clutch springs are cracked or damaged at less than 500,000 miles on a heavy duty truck. These clutches are supposed to last over 1MM miles. Its not a coincidence that every truck we have is failing at the same mileage. These clutches are made defective from the manufacturer. Its also a coincidence that the replacement clutches are not the original design and are of a newer design and brand. THIS is RED FLAGS!!!!
My circumstances are EXACTLY as described in a release 12/19/2019 Tech Service Bulletin A002 I experienced the vibration in my steering wheel that caused me to be suspect that there was something wrong in the drive train. Upon further investigation. I noticed that an oil seal was leaking, and when I dug a little deeper, I noticed gears that were broken and shaved down and then stopped at a Kenworth corporate location upon which they told me that I needed to purchase the entire unit to fix it. I then decided that I...
Read the full complaint
was going to add some differential oil and drive at a speed of 45 miles an hour, which did not cause any vibration to Chicago, which was roughly 3 hours away from my location in Michigan upon which I would have more resources at my disposal. It is then that I learned of the technical service bulletin relating to my issue. I then took it to CIT trucks which is where I learned that you do not have to buy the complete unit that. The parts are available to be purchased to fix the issue. They did, however say that they would process the claim on behalf of this technical service bulletin. They advised me that the individual that they got a hold of seem to have an attitude about it and sometimes this happens whereas other times they will get a hold of somebody that will make an exception. Apparently they stated my situation is two months out of warranty from when my tractor was placed into service but it's original owner. I am not in a position due to other issues that I have experience with the truck since purchasing it in June that I can afford this but more importantly, there is a known issue with the same exact identical problem that I experienced. I need help with my situation they need to be held accountable for what has gone wrong because it is not my fault.
The clutch has a loose spring, Fork is damaged. Throwout bearing worn.
Throw out bearing failed prematurely. Truck only has 491,000 miles and has had a catastrophic failure resulting in a $29,000 repair bill. I have 4 other trucks like this and they are all showing signs of the same thing.
When driving, the truck will not go into gear. For example, if I am trying to shift gears in the automatic, it will stay in that gear. When traveling down the highway, it stays in a gear. I have to find a safe place to pull over and put it in neutral, then proceed. I have already changed the right hand stalk once before and it didnt go into reverse, that was the reason for changing it. I get codes saying that it needs to ve changed again and it was just recently put on.
This truck was breaking automatically, and no one was front of the truck, it was scary, I almost crashed with loaded trailer on my back, it has done it multiple times, and my traction light and stability light is on all the time and adaptive cruise control had turned off completely abs light comes on and off frequently,
On sunday, the 22nd of march, I was traveling south on us hwy 45. The sky was clearing and the road was dry. I had my cruise set to 65 mph. As I approached an overpass, the distance sensor on the front of the truck mistook the shadow of the overpass as a stopped vehicle. Warning lights and buzzers went off and the vehicle did a hard brake. Luckily, there were no other vehicles around me. I took it to our shop and the system was cleaned. Four days later, the sensor mistook an overhead interstate sign for a stopped...
Read the full complaint
vehicle. Again, the warning lights and buzzers and a hard brake. Kenworth techs were sent out to our shop to make repairs. Every one of our drivers that I have spoken to have experienced the same thing multiple times. This is dangerous. If someone had been following me, they would have rear-ended my trailer.
Kenworth T680: every year compared
All T680 years2020 Kenworth T680 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2020 Kenworth T680 | 8 | 8 | C | |
| 2020 Kenworth T170 | 1 | 1 | C | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2020 Kenworth T680
Does the 2020 Kenworth T680 have any recalls?
Yes - NHTSA lists 8 recalls for the 2020 Kenworth T680: reservoir / tank (February 2024); critical fasteners (April 2022); wiring (December 2021); antilock (September 2020) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2020 Kenworth T680?
By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (5), brakes (2), driver assistance (1).
How many complaints has the 2020 Kenworth T680 had?
8 complaints have been filed with NHTSA, the first on April 4, 2020 and the latest on December 8, 2024. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.
Is the 2020 Kenworth T680 a reliable vehicle?
Its Safety Index is 55 out of 100 (grade C: about as many problems as a typical Kenworth T680 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T680 years have the most complaints?
2018 (11), 2014 (10), 2017 (9). See every Kenworth T680 year compared.
What should I do if my 2020 Kenworth T680 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data