- The problem
- Dowels may have been omitted during spring cap installation; this would put shear load on the four (4) spring cap bolts.
- The risk
- This could result in loosening and failure of the boltswith possible loss of control and accident potential.
- The fix
- Install the missing dowels to prevent movement between the spring cap and axle housing.
Vehicle safety record
1988 Mack DMM Series Problems, complaints & recalls
No owner complaints about the 1988 Mack DMM Series have been filed with NHTSA. It is covered by 5 recalls, the latest in March 1989 for the springs.
NHTSA data checked
Rated once enough DMM Series years are on file
- Complaints
- 0
- Recalls
- 5
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
1988 Mack DMM Series recalls 5
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- An incorrect high pressure power steering hose may have been installed.
- The risk
- Under certain conditions, hose could fail resulting inloss of power steering assist and possibly an accident.
- The fix
- REPLACE INCORRECT POWER STEERING HOSES.
- The problem
- Certain engine support castings were produced with faulty metallurgy and could fail.
- The risk
- Failure of one or both brackets could cause dislocationof engine and transmission assembly, which could result in truck disablement,possible loss of accelerator control and an accident.
- The fix
- REPLACE REAR ENGINE SUPPORTS AS NECESSARY.
- The problem
- Some of the nuts/bolts used to fasten the steering pitman arm may loosen.
- The risk
- This would allow the pitman arm to come off the steeringgear sector shaft and result in immediate loss of steering control and a vehiclecrash could occur.
- The fix
- RETORQUE NUTS/BOLTS WHERE NECESSARY.
- The problem
- Clamp plates used between the drive shaft and carrier yokes may crack and could break due to improper heat treatment.
- The risk
- If clamp plate breaks, yoke would fly off at detachedpoint and could injury anyone struck by flying fragments. Also, the detachedinner shaft could interfere with the brake system air supply hoses and tractortires, which could result in loss of truck control and an accident.
- The fix
- Install new clamping plates and capscrews in all locations as needed.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
No complaints about the 1988 Mack DMM Series yet
Mack DMM Series: every year compared
All DMM Series years1988 Mack DMM Series vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1988 Mack DMM Series | 0 | 5 | - | |
| 1988 Mack Mack | 4 | 2 | D | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1988 Mack DMM Series
Does the 1988 Mack DMM Series have any recalls?
Yes - NHTSA lists 5 recalls for the 1988 Mack DMM Series: springs (March 1989); hose, piping, and connections (March 1989); engine (October 1988); linkages (July 1988) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
How many complaints has the 1988 Mack DMM Series had?
None have been filed with NHTSA so far.
What should I do if my 1988 Mack DMM Series has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data