- The problem
- Mazda North American Operations (Mazda) is recalling certain 2011 Mazda2 and 2010-2011 Mazda3 and Mazdaspeed3 vehicles equipped with a manual seat lifter. In the affected vehicles, the seat height adjustment lifter links may break or detach from the seat frame and the seat angle may incline causing the driver to not be able to maintain an appropriate driving position.
- The risk
- If the driver cannot maintain an appropriate driving position, there is an increased risk of a crash.
- The fix
- Mazda will notify owners, and dealers will inspect the seat lifter links and install a reinforcement bracket to the lifter links, or replace the entire seat adjuster unit, free of charge. The recall began April 7, 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0917B.
Vehicle safety record
2010 Mazda MAZDA3 Problems, complaints & recalls
Owners have filed 686 complaints about the 2010 Mazda MAZDA3 with NHTSA, most often about the body, doors & structure (172) and the seats & seat belts (113). Those complaints describe 18 crashes, 5 fires and 13 injuries. It is covered by 3 recalls, the latest in February 2017 for the seats. For comparison, the 2009 has 119 and the 2011 has 132.
NHTSA data checked
FFar more problems than a typical MAZDA3 year, for its age
#17 most complained-about 2010 vehicle
- Complaints
- 686
- Recalls
- 3
- Crashes
- 18
- Fires
- 5
- Injuries
- 13
- Deaths
- 0
Most common 2010 Mazda MAZDA3 problems
Share of all 686 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2010 Mazda MAZDA3 recalls 3
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Mazda North American Operations (Mazda) is recalling certain model year 2010-2013 Mazda3 and Mazdaspeed3 vehicles manufactured November 18, 2008, to June 8, 2013, 2012-2015 Mazda5 vehicles manufactured October 26, 2010, to June 22, 2015, 2016 CX-3 vehicles manufactured June 1, 2015, to December 26, 2015, and 2013-2016 CX-5 vehicles manufactured December 15, 2011, to December 26, 2015. On the affected vehicles, the lift gate support struts may corrode, possibly causing the struts to break and/or the lift gate to drop unexpectedly.
- The risk
- If the lift gate falls unexpectedly, it may hit the user, increasing their risk of injury.
- The fix
- Mazda dealers will replace the both lift gate supports, free of charge, however parts are not currently available. The recall began April 2017. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 9916H.
- The problem
- Mazda is recalling 25,400 my 2010 mazda3 vehicles. A clearance between the engine harness and the housing of starter motor may be insufficient. Due to this, the covering of the harness may be damaged through vibration during operation possibly causing a short-circuit between certain harness wires and the starter housing. A short-circuit can result in engine control malfunction and/or poor shift quality.
- The risk
- The main fuse may blow out causing the engine to stall and inability of restart, increasing the risk of a crash.
- The fix
- Dealers will have the engine harness inspect and add a protector clip on the affected section of the harness. If necessary, the harness will be repaired. This service will be performed free of charge. The recall is expected to begin on may 6, 2009. Owners may contact mazda at 1-800-222-5500.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
686 complaints about the 2010 Mazda MAZDA3
Newest first, as filed with NHTSA by owners. Page 1 of 28.
The AT light came on the dash, added transmission fluid because it was a little low but the light still has not gone off. I think there is an electrical problem within the transmission. It's had shifting issues since purchasing this vehicle. I also have a small child that comes with me to work and I do not want my car to catch on fire while we are in this vehicle.
my girlfriend had bought a car from a dealership in Pennsylvania and the car is registered in Pennsylvania at a dealer called premier world wide auto sales. when she had bought the car all four of the tires i believe should have failed pa safety inspection and the owner of this shop keeps telling me that they pass one hundred percent even though the tires have signs of dry rot all the way around all four tires and would not stop giving me problems and trying to prove me wrong the dot codes show that the tires in...
Read the full complaint
the front were 10 years of age and the rear tires at 8 years of age and showing signs of dry rot the tire size all around is 205/55r16 and this is completely unacceptable for a business that has been operating for as long as its been operating because all i can think about is how many other cars has this dealership sold with dry rotting tires nor did they show my girlfriend when she bought the car any of the work that had been done by the shop that had done the inspection prior she was told that everything on this car was great and that there weren't any issues when infact that was not the case i found a leak coming from an engine oil pressure sensor and a cv axle boot torn and flinging grease along with the tires with none of this being disclosed to my girlfriend who bought the car shortly after
NHTSA Complaint Narrative I am filing this complaint regarding a 2010 Mazda 3, VIN [[redacted]] . The vehicle experiences intermittent transmission control failures, including difficulty shifting out of first gear and warning indicators triggered by vibration. The transmission and transmission control module have already been replaced. The dealership has identified the wiring harness as the cause of the remaining failure. Mazda North American Operations has confirmed that the required wiring harness...
Read the full complaint
(BBM9-67-020H) is discontinued and unavailable. However, Mazda has not provided a written determination of whether the known wiring harness recall (engine wiring harness chafing affecting control systems) applies to this VIN, nor confirmed recall completion history. Mazda has advised the customer to seek aftermarket or salvage parts, but has not provided an approved repair remedy or goodwill assistance despite the issue affecting drivability and safety. I am requesting that NHTSA review whether Mazda has met its obligations regarding: 1.recall applicability determination by VIN, and 2.providing an adequate remedy when OEM repair parts are no longer available for a safety-related defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
See attached document for complaint.
I have reason to believe the dealership I bought my vehicle from rolled back my odometer. Upon checking my carfax information, 12/01/24, the odometer read 161,142, which the dealership did own my vehicle at this time. When I bought this car in April of 2025, the odometer was reading 130,000.
On August 15, 2025, my 2010 Mazda 3 began displaying the ABS warning light intermittently while driving. The ABS system is a critical safety feature, and when the light comes on, I am unsure if the braking system will function properly in an emergency. I scanned the vehicle using a Foxwell diagnostic tool and retrieved the following ABS-related fault codes: C0020:1C-2B - ABS Pump Motor Control Circuit U0425:62-60 - Invalid Data Received from IPC/ABS Control Module U0140:00-28 - Lost Communication with Body...
Read the full complaint
Control Module These issues are consistent with Mazda Technical Service Bulletin 04-002/13 (July 17, 2013), which documents ABS pump motor failures caused by poor motor brush contact. This is a serious safety concern because the ABS system fails without warning, leaving the driver and passengers at risk of brake loss in critical conditions. Why this should be investigated: The defect occurs intermittently, making it difficult to predict or reproduce. It matches a known documented defect acknowledged by Mazda in TSB 04-002/13. Other owners have reported similar ABS pump failures in Mazda vehicles of this generation. The failure compromises safe braking and should be treated as a safety defect warranting investigation and possible recall. Action Requested: I am requesting that NHTSA investigate this recurring ABS pump/motor failure in 2010 Mazda 3 vehicles and determine whether a recall should be issued to address this known defect.
The a.b.s pump module is defective in these vehicles. There are tons of people having issues with them. When they fail it happens suddenly resulting in brake failure, power steering failure, the car does not like to shut off, the vehicle will go into "limp mode" and every light on the dash comes on. The part itself is costing close to $1000 u.s.d . With all of tge effected things tgat go with it i believe it can be very dangerous and should be recalled
This vehicle is subject to recall #: 17V-082 referring to a drivers seat lifter link than can break. My car has a broken lifter link, was brought to the dealership and instead of replacing the entire seat adjuster unit like the recall states, they simply installed a reinforcement bracket. When brought back to Med Center Mazda they state it has already been repaired and therefore cannot be repaired again. The vehicle still has a broken seat lifter link.
Transmission slipping. Not shifting correctly.
I purchased two tires from Les Schwab in Molalla, OR on 1/15/25 in which upon them changing the tires they damaged one of my TPMS sensors and they did not replace it. I didn't have a warning light before I went in and now I do and they knowingly did not replace it when TPMS sensor service was part of purchasing the new tires. Instead they quoted me $451.96 to replace the sensors in all 4 tires other than replaced the one they broke. A set of TPMS sensors online cost $28, this is unethical of them to take advantage...
Read the full complaint
of consumers like this and they should be held accountable. If I'm not mistake it says in "49 USC 30122(b)" that "Prohibition.-A manufacturer, distributor, dealer, rental company, or motor vehicle repair business may not knowingly make inoperative any part of a device or element of design installed on or in a motor vehicle or motor vehicle equipment in compliance with an applicable motor vehicle safety standard prescribed under this chapter unless the manufacturer, distributor, dealer, rental company, or repair business reasonably believes the vehicle or equipment will not be used (except for testing or a similar purpose during maintenance or repair) when the device or element is inoperative." 205/55 R16
Transmission control module issues. Car was driving on the expressway and wouldn't shift out of second gear. Engine light and AT light came on. Had to drive slowly on the expressway and get off on the closest exit. Cars were speeding past me and I had to be careful not to get hit. Research and shop shows the 2010 Mazda 3 vehicles have lots of issue with the TCM because they get hot due to there location.
Tha dashboard is melted causing glares on very sunny days and makes driving difficult.
ABS or the ABS computer malfunction or wasn't working correctly and almost cause an accident.
my Mazda 03 dashboard is melting, and I am not able to see out the window... I have talked to dealer and manufactory, and they will not pay the whole amount knowing it's a safety issue. I don't understand how they can sell product on car that is malfunctioning and a safety issue. I bought the car brand new in 2010 and didn't have any issues until this year. Please call me back at [[redacted]] my name is [[redacted]] . I was not in an accident, just think this is a safety issue. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving on the interstate, the driver's side airbag deployed without any obvious cause. There was no pothole, bump, or clear reason for the airbag to deploy. There was moderate traffic. This put myself and others nearby at risk by causing me to flinch after getting hit by the airbag. I was lucky to not swerve into anything or cause any damage. It caused temporary loss of hearing and a sore neck, but no serious injury. Prior to the failure, there were no dash lights, messages, or other symptoms.
ABS module malfunction all four wheel speed sensor not read in the same time and powersteering cut off cause by unready wheel speed check engine light ABS light and Steering Light on.
ABS will cause complete brake failure when it is engaged. For example, needing to stop quickly to avoid hitting another vehicle and the brakes will lose all pressure and the vehicle will not stop. Several mechanics have not been able to diagnose or fix. Immediately after the incident, there will be minimal brake pressure of about 20%, eventually it will return to normal. Must avoid applying brakes in emergency situations as it will actually be worse than attempting to steer out of it. This has happened about 6 times in 4 years. It happened the first time about 3 days after I bought the vehicle in 2019.
TCM has failed to communicate in engine. Car doesn't not shift properly or has hard shifts if it is able to get back into gear. Car may experience AT engagement making it hard to steer and control vehicle. Can happen in the middle of driving. Independent service Auto mechanic shop Vehicle has no warning lights indicating failure until hard shift when driving 50miles per hour and engine would no longer speed up AT light then came on. Once parked for two days check engine light came on and vehicle no longer would shift into gear.
Fuel is leaking from the top of the gas tank, which is a very dangerous issue.
Abs light stays on, break light stays on. Abs is not working.
Power Steering sometimes works and sometimes not. Can go out and stop working or start working, in the middle of driving. i noticed Mazda has a recall for 2007, 2008, 2009 Mazda 3 cars, but *NOT* 2010 Mazda 3. I suspect the same issue.
The dashboard adhesive migrates to the surface of the dashboard. Adhesive then sublimates and condenses on the windshield making a glaze on the windshield, making it extremely difficult to see the road in sunrise or sunset conditions. I've repeatedly cleaned the windshield with many different cleaners including acetone, but at best I am only able to improve visibility, not restore it. In the attached photo, the upper portion of photo illustrates the film of adhesive on the glass after it was wiped with a clean paper towel, creating a hazy appearance. The entire windshield was cleaned with acetone and heavy duty degreaser and window cleaner prior to the photo.
The contact owns a 2010 Mazda Mazda3. The contact stated that the adhesive tape on the instrument panel was melt, making it difficult to see the instrument panel. The vehicle was taken to the dealer who stated that the instrument panel needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and made aware of failure. The contact was informed that an Extended Warranty for the failure had expired. The failure mileage was 105,000.
Monday 7/10/2023 car was fine ie (the seat) next day Tues 7/11/2023 opened drivers side door couldn't believe my eyes. The driver seat had somehow migrated clear up to an inch from my chest to the steering wheel. I called Maple Shade Turnersville to make an appointment-wasn't able to get in until 7/20/2023. I was told I had to return on 7/24/2023. Did that. Appt was 7:30AM. Was given a loaner car. At around 10:30 Am Mazda Tuenersville called to ask me to return the loaner (?). When I arrived Pat Kearny told me he...
Read the full complaint
couldn't do anything to help with the car seat. Told me my car was too old that they didn't make parts for my 2010 Mazda 3 for the already recalled seat problems. Now I'm in a big bind. My steering wheel is one inch from my chest. I am very upset what happened here.
Mon-7/10/2023 used the car. Tues 7/11/2023 attempted to use my car opened the door on the drivers side-saw a bizarre position of the seat. It had somehow migrated during the night to approx 4" from the steering wheel when I try to get into the seat my chest stomach area is an inch away can't reach the pedals very well because my right knee is up against the dashboard. Took the car to the dealership the man in charge told me there's nothing they could do the car is too old. He told me to take it to an independent repair shop to get the parts from junk yard. Said he would have to cut the bolts on the seat track said he couldn't do that. Please see the photos and video.
Mazda MAZDA3: every year compared
| Year | Complaints | Recalls | Grade |
|---|---|---|---|
| 2014 | 138 | 4 | C |
| 2013 | 117 | 1 | C |
| 2012 | 226 | 1 | D |
| 2011 | 132 | 2 | C |
| 2010 | 686 | 3 | F |
| 2009 | 119 | 4 | C |
| 2008 | 303 | 3 | F |
| 2007 | 222 | 3 | D |
| 2006 | 166 | 2 | D |
2010 Mazda MAZDA3 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2010 Mazda MAZDA3 | 686 | 3 | F | |
| 2010 Toyota Prius | 2,823 | 10 | F | Compare |
| 2010 Toyota Corolla | 1,264 | 17 | F | Compare |
| 2010 Volkswagen Jetta | 875 | 5 | F | Compare |
| 2010 Hyundai Elantra | 455 | 3 | D | Compare |
| 2010 Honda Civic | 398 | 8 | F | Compare |
| 2010 Kia Forte | 232 | 3 | C | Compare |
| 2010 Nissan Sentra | 144 | 3 | F | Compare |
| 2010 Volkswagen Golf | 70 | 4 | F | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2010 Mazda MAZDA3
Does the 2010 Mazda MAZDA3 have any recalls?
Yes - NHTSA lists 3 recalls for the 2010 Mazda MAZDA3: seats (February 2017); hatchback / liftgate (September 2016); electrical system (April 2009). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2010 Mazda MAZDA3?
By the complaints owners filed with NHTSA, the most common problem areas are the body, doors & structure (172), seats & seat belts (113), visibility & wipers (109).
How many complaints has the 2010 Mazda MAZDA3 had?
686 complaints have been filed with NHTSA, the first on September 14, 2009 and the latest on April 4, 2026. Of these, 18 describe a crash and 5 a fire, and together they report 13 injuries and 0 deaths.
Is the 2010 Mazda MAZDA3 a reliable vehicle?
Its Safety Index is 9 out of 100 (grade F: far more problems than a typical Mazda MAZDA3 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Mazda MAZDA3 years have the most complaints?
2010 (686), 2008 (303), 2012 (226). See every Mazda MAZDA3 year compared.
What should I do if my 2010 Mazda MAZDA3 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data