PACCAR Incorporated (PACCAR) is recalling certain 2016-2020 Peterbilt 320 and 520 vehicles with dual foot valves and a liftable tag or tri-drive rear axles. The rear brake signal hose may be missing a quick release valve, possibly causing a delay in their...
Brakes
Peterbilt 320 Brake problems by year
1 complaints filed with NHTSA about the Peterbilt 320's brakes. Spongy or hard pedal, ABS faults, brake failure, noises, parking brake and brake fluid leaks.
Brake complaints by model year
Brake recalls
PACCAR Incorporated (PACCAR) is recalling certain 2017 Peterbilt 320 vehicles, equipped with Meritor disc brakes. The park brake chamber on these vehicles may be to small, which can cause the vehicle to move unexpectedly. As such, these vehicles fail to...
PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Peterbilt 210, 220, 320, and Kenworth K270, K370, T660, T800, T880 trucks manufactured July 21, 2014, to September 16, 2014. The brake caliper bolts may not be properly torqued.
Paccar is recalling certain model year 2012-2013 kenworth t170, t270, t370, t440, t470, t660, t700, t800, w900, and peterbilt 320, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 vehicles, manufactured from january 31, 2011, through january 19...
Peterbilt is recalling certain model year 2010 320 trucks equipped with hendrickson hlr2 non-steering pusher axle for failing to comply with requirements of federal motor vehicle safety standard no. 121, "Air brake systems." The trucks were not manufactured...
Certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 106, "Brake hoses." The tubing was manufactured with only four layers of nylon...
Certain trucks equipped with bendix sr-7 spring brake modulating valves. The internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
On certain heavy duty trucks equipped with meritor wabco pneumatic anitlock brake system (abs) valve packages, the assembly bolts on these valve packages were not tightened correctly.
Vehicle description: heavy duty trucks equipped with dual steering. Interference between the cab floor and the brake pedal can occur on the right hand side of the dual steer vehicle.
Latest 320 brake complaints
The 2010 peterbilt 320 garbage truck was returning from the waste disposal site. The driver applied the brakes and the brake pedal broke off the mounting brackets that secures the brake pedal to the floor and the petal fell over sideways, resulting in the loss of braking ability for the truck. The two very small brackets, one on each side of the brake pedal which has a rod in the bottom the goes through the pedal and into each bracket which peterbilt calls a bearing. The brackets (bearings) both deteriorated as...
Read the full complaint
they are made of a very light pot metal type material and when the brake was applied broke into several pieces. The truck was put into service in october 2010, less than 2 years ago. We also have another peterbilt 320 that has the same components that are also deteriorating. I went to the dealer and got replacement brackets (bearings) which are made of a heaver steel type material but the brackets (bearings) are still of the same style which are very small and I believe with the force that a driver uses on any brake petal these should be of a heavier type construction and size. I believe at a minimum that all peterbilt 320's with these style brackets (bearings) should be recalled and the new heavier material brackets (bearings) be installed until the whole assembly is resigned to a higher and more reliable standard and replaced on all of these trucks. I do have the old pieces and pictures of them that I could send you.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data