- The problem
- Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4201 or kenworth at 1-425-828-5440.
Steering
2000 Peterbilt 379 Steering problems
Owners have filed 2 complaints about the 2000 Peterbilt 379's steering with NHTSA - 17% of all its complaints, most recently on November 29, 2001. Loss of power steering, stiff or loose steering, wandering, column and rack problems.
- Complaints
- 2
- Recalls
- 3
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Steering recalls for the 2000 Peterbilt 379
- The problem
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks. The bolts used to secure the steering shaft can fail.
- The risk
- This condition can result in the loss of vehicle control without warning, increasing the risk of a crash.
- The fix
- Dealers will replace the defective bolts. Owner notification began april 2, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000.
Steering complaints
Vehicle is leaning too much to the left. Vehicle has been to the dealer and several independent repair shops, and no one can correct the problem, asking nhtsa to assist on this issue.*Ak. Several mechanic discovered that the steer tires were worn, the steer axle wheel bearing was broken and the right steer axle kinpin had excessive play, the vehicle was aligned, the clutch was adjusted, the steering was tight, and the steering gear box was replaced.*Jb
Power steering reservoir mounting bracket broke, owner was informed that a service bulletin was issued and that a replacement bracket would be installed if the existing bracket was cracking, consumer suggests an angle type bracket be fabricated and bolted to the existing reservoir bracket, then bolted to the lower intake manifold bolt, this would elimate torsion stresses on the reservoir brackets at the timing cover where cracks begin. *Slc
Peterbilt 379 steering complaints by year
379 steering problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data