Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Suspension

2003 Toyota Sequoia Suspension problems

Owners have filed 45 complaints about the 2003 Toyota Sequoia's suspension with NHTSA - 7% of all its complaints, most recently on August 17, 2026. They describe 3 crashes, 0 fires and 3 injuries. Broken springs, struts, control arms, ball joints, noises and alignment that won't hold.

Complaints
45
Recalls
1
Crashes
3
Fires
0
Injuries
3
Deaths
1

Suspension recalls for the 2003 Toyota Sequoia

Suspension: lower ball joint

05V225000768,379 vehicles affected

The problem
On certain sport utility vehicles, due to a manufacturing issue in the front suspension lower ball joint, there is a possibility that the surface of the ball of the joint may have been scratched. The ball joint may eventually experience excessive wear and looseness, resulting in increased steering effort.
The risk
The lower ball joint may separate from the knuckle causing loss of steering control and a crash could occur.
The fix
Dealers will replace the front suspension lower ball joints free of charge. The recall began on july 5, 2005. Owners may contact toyota at 1-800-331-4331.

Suspension complaints

SuspensionBody, doors & structure

My 2003 Sequoia was in the garage for a check on the brakes. I also asked them to check the frame for any rust issues, because I had previously been concerned about it earlier. They reported to me that the car should be off the road because the rust in the frame was so severe. They said they would not put it up on the lift anymore because it could break in half. The stabilizer was barely connected at one end. There were holes completely through the frame at several places. I know from my research that Toyota issued safety recalls for 2003 Sequoia and Tundra vehicles. This an issue that Toyota should repair.

Filed Incident Suspension · StructureNHTSA 11757568
SteeringSuspensionAcceleration & cruise control

Front end in rolled shacking. Tires wearing extremely fast and uneven image. Unable to drive

Filed Incident Steering · Suspension · Vehicle speed controlNHTSA 11576522
SteeringSuspensionBody, doors & structure

Abnormal rust all over underside of vehicle including frame, structural components, brake lines, steering components ... etc. FRAME and steering/suspension components rusting out. Rear differential rusting out. Cab mounts rusting out. Spare tire hardware rusting out. Transmission cooler lines about to burst from corrosion. Rear tow assembly rusting out. Entire underside is rotting out. Known issue which has plagued hundreds of owners, but Toyota has not recalled this model year. Extremely dangerous; one brake line...

Read the full complaint

has already gone out resulting in a loss of braking. Toyota applied an undercoating circa 2013 but they just sprayed over an already rusted frame and other components without proper preparation which actually accelerated the corrosion and rot. Deceptive and unethical business practices. Vehicle cost over $50,000 new in 2003 and only has just over 120,000 miles on it. This should NOT be happening. Please help. Please investigate.

Filed Incident Steering · Suspension · StructureNHTSA 11471811
SuspensionBody, doors & structure

Hello, I am writing to you to have an investigation started on 2003 Toyota Sequoia, I own one and there has been concerns with the Frame of the vehicle rotting out, there was Warranty Enhancement Program sent out in United States to cover frames of 2001 to 2004 Toyota Sequoias which replaced severely rusted out frames at the dealership. I use this vehicle for my family and I do not want to endanger the lives of them and the people around the community where the frame may break due to rust and cause a severe...

Read the full complaint

accident. Please take a look at the details below and get back to me. Subject: Limited Service Campaign (LSC) CSD Certain 2001 through 2004 Model Year Sequoia Vehicles Frame Inspection I am located in Canada would like NHSTA to investigate and see if this program can be administered to vehicles in Canada since I have severe rotting of the frame and I have had to have it welded many times to not compromise the safety of the vehicle

Filed Incident Suspension · StructureNHTSA 11440777
SteeringSuspensionWheels & tiresCrash3 injuries1 death

Unknown

Filed Incident Steering · Suspension · WheelsNHTSA 11435335
Suspension

The latch hook/truck door release has a defect. It has been replaced 3 times after purchase of my vehicle , by the following Toyota dealerships (Tejas Toyota in Humble Texas (2x); Maund Toyota in Austin, Tx (1x). Each dealership service said it was/is manufacture defect with the latch hook and it stops "un latching when the vehicle the button is pressed to unlock and the handle can not open the hatchback" This time I was traveling out of state with my pet in the kennel and when we stopped for restroom break the...

Read the full complaint

latch would not open to retrieve the pet to let out the kennel. We were traveling with a vehicle full of items, which the entire inside of the vehicle had to be emptied I ordered to let all the seats down and try to maneuver to try to get my dog out of kennel I. Such a small confined space that was hard to open because it was in the side. It took over and hour to cut the cage at the top to retrieve my pet. The sad part is there was no warning because we were traveling a 13 hour trip, stopping every couple hours for breaks and stretches, and the couple hours before we open the hatchback just fine. This is more than a safety concern for the animal. This is also the ares for retrieving the spare tire underneath the vehicle when the spare has to be released. I have replaced the part 3 times and I am charged $600 cost for parts and labor, when Toyota is aware of the defect. I just had the part replaced 19 months ago and Toyota only gives a 12 warranty on the part. This is ludicrous when the manufacture is aware of the ongoing problem. I have purchased 4 prior Toyota's and never had had this type of problem. My second safety issue is the case gage drops below the empty gage and stays there even though there is gas in the vehicle. The dealership said there was a recall years ago but I never received any notice. Please advise.

Filed Incident Suspension · Unknown or otherNHTSA 11430913
Suspension

Tl* the contact owns a 2003 toyota sequoia. The contact stated that while having a tire replaced on the vehicle, the technician noticed that the driver's and passenger's side underneath the vehicle was extremely corroded. The technician deemed the vehicle unsafe to drive. The vehicle was not repaired. No dealer was contacted. The manufacturer was notified of the failure and informed the contact that the vin was not under recall. The failure mileage was approximately 235,000.*Dt*dt

Filed Incident SuspensionNHTSA 11406936
SuspensionAirbagsFuel system

When driving about 45 or 60 mph the steering wheel shakes real bad an vibrates feels like I got a flat tire or feels like I'm gonna have a tire come off when I bought it also consumes a lot of gas ust to get real good gas mileage but now not so good juust to fill up twice a week but now sometimes 3 to 5 timeswhich is weird didn't know I had a recall warranty I have had to replace a lot of things especially in the emissions part for car bought new fuel line solenoids , purge solenoid, now it says I need a new...

Read the full complaint

valve vent solenoid. There is a vacuum leak other than that runs good doesn't over heat or break unless I needed to but uses a lot of ga shakes real bad I don't wanna drivemorethan 70 mph all the tires are at 41 psi

Filed Incident Suspension · Air bags · Fuel / propulsion systemNHTSA 11279303
SuspensionBody, doors & structure

Took vehicle to local toyota dealership due to steering issue - when I would hit a bump I would loose control of the steering. Inspection showed the vehicle under body and frame has completely rusted, there are sever holes and the trailing arm has separated from the frame. I am not the original owner, but toyota had a recall on the frame during the prior ownership and the vehicle was serviced multiple times at a toyota dealership during the recall and the problem was not addressed. Toyota refuses to offer any assistance at this time.

Filed Incident Suspension · StructureNHTSA 11242288
SteeringSuspensionWheels & tiresCrash

"Ball joint failure" while travelling down freeway at 35-40 mph the passenger front tire had come off and caused the vehicle to drop. Lost steering, brakes and any control of the vehicle at this time. The vehicle skid into the guard rail spinning it around and sliding until it came to a stop. The arm came directly off the vehicle and is still attached to the wheel.

Filed Incident Steering · Suspension · WheelsNHTSA 11196223
Suspension

The frame on the car is rusting away with only 40k miles on it. It was garage kept.

Filed Incident Suspension · Unknown or otherNHTSA 11196212
SuspensionBody, doors & structure

2003 Toyota sequoia limited 4x4 failed massachusetts inspection this month for a severely rusted frame with severe perforation. Additionally, the rear suspension and trailing arms may break off at any time. The vehicle was recalled and had a coating applied several years ago - this only masked the problem. The vehicle was always garaged. The engine and body of the vehicle are in good condition. The vehicle has 300,000 miles and runs well. The toyota dealer deemed the vehicle "not repairable." The vehicle was also deemed unsafe and advised to take off the road.

Filed Incident Suspension · StructureNHTSA 11096587
SuspensionBody, doors & structureDriver assistance

So many problems with this vehicle, and a major problem not only with this vehicle but other years and models as well the paint bubbling and coming off the vehicle especially hood area and top of vehicle, has to be bad paint toyota is using

Filed Incident Suspension · Structure · Electronic stability control (ESC)NHTSA 11057020
Suspension

The chassis is very rusty and I want to change the shocks but I don't want to damage the car because I believe that chassis have to be fixed first and I don't know how much that cost or where to go to fixed

Filed Incident SuspensionNHTSA 10956690
SuspensionBody, doors & structure

Replaced o2 sensor and was unable to obtain sticker due to frame is rusted. Have three teenage drivers using truck and is now unsafe. Have owned vehicle since 2007 and have serviced at woburn toyota in woburn,ma. I have never got an email or mail from toyota pertaining any issue. When asked about it said been out for a while!!!

Filed Incident Suspension · Structure · Unknown or otherNHTSA 10949509
Suspension

FRAME IS RUSTING AWAY AT ONLY 40K. HOLES IN FRAME.

Filed Incident SuspensionNHTSA 10947998
SuspensionBody, doors & structure

I purchase this 2003 toyota sequoia in 2003 brand new and at the moment the frame is rusting at an alarming rate. I would like to know if the manufacturer (toyota) is making any plans to rectifying this problem?

Filed Incident Suspension · StructureNHTSA 10864994
SuspensionBrakes

The 2003 sequioa frame is rust is eating away the frame. We paid a lot of money for this vechicle. Would toyota standby there vechicle and replace this frame or we have pay for replacement .

Filed Incident Suspension · Service brakesNHTSA 10861474
Suspension

The vehicle was making noises while driving that we could not identify. My daughter was driving it to pick up a friend and when she turned into the driveway, the right rear axle disconnected from the frame. The overall frame is entirely rusted out. Pretty big safety issue. Thankfully, she was not driving faster when this occurred.

Filed Incident SuspensionNHTSA 10764143
SuspensionAcceleration & cruise controlDriver assistanceBrakes

Going around a turn in the mountains at a slow speed, my traction control kicks in and there is a grinding noise, I loose the use of the brakes completely until the traction control turns off. I took it to the dealer and they told me my springs and shocks were bad. I replaced all 4 of the springs and shocks and the problem persists. This is very dangerous and scary. *Tr

Filed Incident Suspension · Vehicle speed control · Electronic stability control (ESC) · Service brakesNHTSA 10630907
SteeringSuspensionBody, doors & structure

Received a letter from toyota for a limited service campaign, for rusting of the frame. I took my toyota to koons toyota in annapolis, md. They called me the next day and said it failed for rust. There was a hole in my frame and toyota would replace the frame at no cost to me. Then they called me to tell me it would cost $6,400.00 To replace everything under the vehicle, because it was so rusted out that when they took the parts off they would crumble. Two days later they called and told me it would cost...

Read the full complaint

$6,900.00 To replace parts. They called last night and said it would cost me $7,845.00 And they could not guarantee the price would not be higher.They sent me pictures of my frame and there is a large hole in the frame. My question is shouldn't I get my truck back in working condition without me paying for anything? I contacted toyota in ca. And talked to the rust specialist, and he said they would not pay for my parts. My husband and I are retired and live on a fixed income. We can not afford to pay for the parts. The truck has been paid for once, why should I take out a loan for a truck that has been paid for. The dealer also asked us to come pick up my truck if I would not authorize to pay for the parts. When I picked up my truck today, they said if anything happened to the truck while I was driving it home, they would not be responsible, because I didn't get it fixed. Please make toyota recall these rusted trucks back. The rusted frame also includes tundras, because they use the same frame. Thank you. *Tr

Filed Incident Steering · Suspension · StructureNHTSA 10496750
Suspension

Tl* the contact owns a 2003 toyota sequoia. The contact stated that he noticed rust spots on the frame of the vehicle. Over time, he would hear a loud banging noise. The contact inspected the vehicle and found that the stabilizer bar had become completely detached from the frame. The vehicle was taken to the dealer, who advised that because of the vehicle weight, the frame could not handle the stress. The contact was advised to park and no longer drive the vehicle. The manufacturer was contacted but advised that...

Read the full complaint

they would provide no assistance. There were no recalls for the year, make and model that pertained to the failure the contact experienced. The vehicle was not repaired. The failure mileage was approximately 117,000.

Filed Incident SuspensionNHTSA 10489350
SuspensionDriver assistanceBrakes

Problem one: "brake" warning light comes on at random but then doesn't come back on at next restart of car. Brake fluid and all mechanics are ok. Braking doesn't seem to be affected but I am worried that there will be an abs failure that I'll ignore because of this faulty warning light. Sometimes the stability control activates for no reason at low speed. Problem two: frame is nearly rusted out. There is a recall for the similar tundra, and supposedly a recall for these particular sequoias in some states, but nothing comes up for my vehicle in indiana. Vehicle, purchased from toyota dealer oxmoor toyota a year ago, is unsafe to drive. *Tr

Filed Incident Suspension · Electronic stability control (ESC) · Service brakesNHTSA 10481250
SteeringSuspensionBody, doors & structure

Frame is completely rusted and cracked in various areas. *Tr

Filed Incident Steering · Suspension · StructureNHTSA 10471397
SteeringSuspensionBody, doors & structure

I took the sequoia to a mechanic to repair a clunking noise in the front and squeaking noise in the back. Upon examination, the mechanic noticed unusually advanced rust and corrosion for a vehicle of its age. For safety reasons, the mechanic warned against driving the vehicle until repairs were made. Mechanic had to cut out front passenger control arm bolts, rear shock mounts, and other hardware due to the corrosion. Mechanic noted that future repairs will require the same cutting and replacement of new hardware. This corrosion issue may be related to the 2000-2003 toyota tundra recall of 2009, since the sequoia shares the chassis and manufacturing facility with the tundra. *Tr

Filed Incident Steering · Suspension · StructureNHTSA 10469342

Toyota Sequoia suspension complaints by year

Sequoia suspension problems, every year

Had a suspension problem with your 2003 Sequoia? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience