- The problem
- Altec Industries, Inc. (Altec) is recalling certain 2004-2023 DL42 and DL45 Digger Derricks. The incorrect hydraulic load holding valve may have been installed, which can cause the winch to lower uncontrollably and the load to fall.
- The risk
- An uncontrolled load falling increases the risk of injury to personnel or others nearby.
- The fix
- Altec will replace the load holding valve, free of charge. Owner notification letters are expected to be mailed October 6, 2023. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is MAB 3113.
Equipment & accessories
2011 Altec Digger Derrick Equipment problems
No owner has filed a complaint about the 2011 Altec Digger Derrick's equipment & accessories with NHTSA. Trailer hitches, mobility equipment, accessories and aftermarket parts.
- Complaints
- 0
- Recalls
- 8
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Equipment recalls for the 2011 Altec Digger Derrick
- The problem
- Altec Industries Inc. (Altec) is recalling certain 2009-2019 DL/DM, DL/DMB, DH, D/2/3/4, and DC Digger Derrick vehicles. The slope indicator placard card may falsely indicate that the unit could be used without leveling on a 5 degree slope.
- The risk
- An operator may improperly set up the unit, making the unit unstable, thus increasing the risk of injury.
- The fix
- Altec will notify owners, and issue CSN 719 to owners, instructing them to remove the incorrect placards, free of charge. The recall began July 2, 2019. Owners may contact Altec customer service at 1-877-462-5832. Altec's number for this recall is CSN 719.
- The problem
- Altec Industries, Inc (Altec) is recalling certain 2003-2019 Altec DL/DM, DL/DMB, and DC Digger Derrick vehicles. The pedestal tube welds may crack over time.
- The risk
- Unrepaired cracks may result in failure of the pedestal and uncontrolled movement increasing the risk of injury.
- The fix
- Altec will notify owners and will provide repairs as necessary and a reinforcing kit. The recall began April 3, 2019. Owners may contact Altec's customer service at 1-877-462-5832. Altec's number for this recall is CSN 713.
- The problem
- Altec Industries Inc. (Altec) is recalling certain model year 2009-2013 DT80, and model year 2011-2013 D2, D3 and D4 digger derrick models manufactured June 2009 through November 2013. The fasteners that hold the bracket for the feeder tube (the telescopic hydraulic tube that supplies pump flow to the auger) may become loose allowing the feeder tube to fall.
- The risk
- A falling feeder tube increases the risk of injury to people nearby.
- The fix
- Altec will notify owners, and Altec service centers will install an upgraded feeder tube bracket and mounting hardware, free of charge. The recall began on February 19, 2014. Owners may contact Altec at 1-877-462-5832. Altec's number for this recall is CSN 591.
- The problem
- Altec Industries, Inc (Altec) is recalling certain model year 2007-2012 DC, and DL/DM Digger Derrick utility trucks, equipped with boom tip winches using Tulsa Winch Group (formerly Gear Products) winch drums. In the affected vehicles, the winch drum could deform or fracture.
- The risk
- If the winch fails while in use, it could cause personal injury.
- The fix
- Altec will notify owners and dealers will replace the winch drum, free of charge. The recall began on June 10, 2013. Altec's recall campaign number is CSN 574.
- The problem
- Altec Industries, Inc. is recalling certain model year 2011-2012 Digger Derrick vehicles equipped with a PENGO digger extension shaft. A defect in the base material at the weld joint may result in a stress fracture through the applied weld of the drive hub to the hex bar material.
- The risk
- The stress fracture could cause the extension shaft to separate from the drive hub when digging, increasing the risk of personal injury and/or property damage.
- The fix
- Altec will notify owners, and will inspect the PENGO digger extension shaft and, as necessary, replace the shaft, free of charge. The safety recall began on October 12, 2012. Owners may contact Altec Industries at 1-877-462-5832.
- The problem
- Altec is recalling certain model year 2008 through 2011 utility vehicles equipped with sure power battery separator devices, part number 16511893 (model 1314) or 16512967 (model 1315). The battery separator can overheat.
- The risk
- Overheating of the battery separator can result in smoke and possible fire.
- The fix
- Altec will notify owners and replace the batter separators free of charge. The safety recall began on january 11, 2012. Owners may contact altec at 1-877-462-5832.
- The problem
- Altec is recalling certain model year 2011 dl/dm series, d4000a, and db37 digger derrick service utility vehicles manufactured from january 2011 through april 2011, equipped with pq single axis boom controllers. The mechanical interlock (lock out) may not operate properly.
- The risk
- If the control interlock does not function properly, the control handle can be accidently shifted causing movement of the unit, possibly resulting in serious injury or death.
- The fix
- Altec will notify owners, and altec dealers will replace the hand controllers free of charge. The safety recall began on september 7, 2011. Owners may contact altec at 1-877-go-altec (1-877-462-5832) for more information.
Equipment complaints
No complaints about this area yet.
Altec Digger Derrick equipment complaints by year
Digger Derrick equipment problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data