Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2000 Chrysler Sebring Convertible Problems, complaints & recalls

Owners have filed 78 complaints about the 2000 Chrysler Sebring Convertible with NHTSA, most often about the seats & seat belts (27) and the brakes (11). Those complaints describe 3 crashes, 2 fires and 5 injuries. It is covered by 2 recalls, the latest in December 2010 for the lower arm. For comparison, the 1999 has 91 and the 2001 has 0.

NHTSA data checked

FFar more problems than a typical Sebring Convertible year, for its age

#105 most complained-about 2000 vehicle

Complaints
78
Recalls
2
Crashes
3
Fires
2
Injuries
5
Deaths
0

Most common 2000 Chrysler Sebring Convertible problems

Share of all 78 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2000 Chrysler Sebring Convertible recalls 2

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Suspension: lower arm

10E05900022,689 vehicles affected

The problem
Federal-mogul is recalling certain replacement control arm assemblies, part numbers k7425, 10945, fa4510x, k7427, 10946, and fa4611x, sold for use on various passenger vehicles listed above. The ball joint on the control arm assembly can fail causing the ball stud to wear through the control arm housing resulting in noise and/or separation of the ball stud from the housing.
The risk
If there is a separation of the ball stud from the housing, the driver can loose steering control, possibly resulting in a vehicle crash.
The fix
Federal-mogul will notify owners of record and replace the affected control arms free of charge. The safety recall began on january 28, 2011. Owners may contact federal-mogul at 1-877-489-6659.

Suspension: lower ball joint

09E0560005,787 vehicles affected

The problem
Qualis automotive is recalling certain aftermarket ball joints sold for use on certain passenger vehicles. The socket may have been excessively hardened which could cause it to crack near the retaining ring groove allowing the ball stud to separate under impact load. The subject ball joints were sold as four part numbers, d10945, d10946, g10945, and g10946. The affected control arms, d10945 and d10946, are stamped with the following dates on the ball joints: 134308, 135708, 100109, 102709, 104109, 105509, 107609, 108909, 110309, 113209, and 116609. The g10945 and g10946 are the same part as the d10945 and d10946 respectively. They are labeled differently depending on the aftermarket customer.
The risk
Separation of the ball stud from the socket of the ball joint housing would allow the control arm to collapse and the wheel to fold in causing loss of steering control, possibly resulting in a crash.
The fix
Qualis automotive will replace the ball joints free of charge. The safety recall began on november 9, 2009. Owners may contact qualis automotive at 1-800-493-4128.

What owners say

Be the first Sebring Convertible owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

78 complaints about the 2000 Chrysler Sebring Convertible

Newest first, as filed with NHTSA by owners. Page 1 of 4.

Airbags1 injury

At approximately 20 mph on a quite neighborhood street both air bags went off with no accident, big bumps or dips or any other reason. I have photos but do not know how to up load them. *Dsy.

Filed Incident Air bagsNHTSA 11064485
Acceleration & cruise controlBrakesCrash

Tl* the contact owns a 2000 chrysler sebring convertible. While pulling out of a car wash, the vehicle was shifted into drive with the brake pedal depressed. The vehicle suddenly accelerated without warning. The vehicle was towed to a tow lot were it was awaiting inspection. A police report was filed. The manufacturer was not made aware of the failure. The failure mileage was 60,000. Updated 05/16/17*lj *cn

Filed Incident Vehicle speed control · Service brakesNHTSA 10955085
Electrical systemFire

Tl* the contact owns a 2000 chrysler sebring convertible. The contact stated that the wiring harness caught fire. The contact stated that the rain extinguished the fire. A fire report was not filed. A police report was filed. The vehicle was not occupied. The vehicle was not diagnosed nor repaired. The manufacturer was not notified. The failure mileage was approximately 80,000.

Filed Incident Electrical systemNHTSA 10863207
Seats & seat belts

Drivers inboard seat belt broke off when my son tried to buckle up in the driveway. Potentially a fatal situation in an accident. The connecting cable frayed. It would not have held in any type of forward accident.

Filed Incident Seat beltsNHTSA 10837448
Wheels & tires

Took my car in 10/23/15 to have the tires rotated and was told by the shop I needed new tires that they were almost bald and the thread indicators were showing on all 4. My tires had only 20k miles on them and the warranty was for 60k miles. Shop said they would contact falken tires and call me back. Falken jerked the shop around for over a week passing him from dept. To dept. Red flag!!!! In the meantime I checked w/ several other shops and in online forums and reviews. All said they had they're tires wear...

Read the full complaint

out in 6-8 months or more. The shops said because of the wear problems they wouldn't sell them and falken had shortened the warranty to 40k and 5 years. Many submitted claims and were denied 2 or 3 times. The shop was told by falken for me to buy new tires and they'd reimburse me if they found a problem w/ the tires. Am disabled on a fixed income and can't do this. What good is a warranty if the company is going to ignore you? I don't trust falken the company or the brand based on their deception and not recalling a defective product based on many many problems. These are falken ziex 912's size 205/65/r15. Things remain right at a stalemate, but I have sent a letter to the falken ceo.

Filed Incident TiresNHTSA 10809826
Electrical system

Alarm system will activate multiple times automatically while the vehicle is park. When driving, the doors will luck and unluck multiple times and all the interiors lights will turn on and off at the same time the doors will luck and unluck.

Filed Incident Electrical systemNHTSA 10747207
Seats & seat belts

The seats belts will lock and you cannot loosen them. If you are just entereing the car you cannot put them on.

Filed Incident Seat beltsNHTSA 10743604
Engine & cooling

When applying brakes after pulling into a parking space, engine stalls. Sometimes engine (car) stalls when stopped at traffic light or stop sign or stopping before backing out of driveway into the street. No codes show up on the car computer. Have had checked out twice.This is ongoing for two months and happens every time I drive the car.

Filed Incident EngineNHTSA 10716776
Suspension

Tl* the contact owns a 2000 chrysler sebring convertible. The contact stated that while parking, there was an abnormal noise coming from the front end of the vehicle as the steering wheel became difficult to maneuver. The contact discovered that the ball joints in the suspension system became detached from the housing. The vehicle was not repaired. The contact was made aware nhtsa campaign number: 10e059000 (suspension), however, the vin was not included in the recall. The manufacturer was made aware of the failure. The approximate failure mileage was 154,000. Updated 12/19/14*cn updated 05/27/2015 *js

Filed Incident SuspensionNHTSA 10618740
Airbags

This morning at approximately 8:00 a.M. Central, my husband and I were awaken to our car horn blaring. I am quite sure that all of our neighbors are now awake as well. We tried to turn it off thinking it was the panic button, but turn out that it was the horn. My husband had to press on it repeatedly to make it stop. He gets out of the vehicle, and as soon as he shuts the door, it start blaring again!!! He then leaves the car door open and starts the vehicle to heat up the engine, since we had freezing...

Read the full complaint

temperatures the last couple of nights. It wasn't until the engine was warm that he was able to shut the door without it going off again. I googled the problem online and found that many others have had the same issue with this type of vehicle and some have experienced the horn going off while driving!!!! I also have read where the dealerships are not taking responsibility for this problem, as it should be a recall issue and covered 100%!! It is very annoying and embarrassing, but also a danger if it occurs while people are driving!!!!!! *Tr

Filed Incident Air bagsNHTSA 10555155
Seats & seat belts

All seatbelts in the car have stopped functioning. It started with the belts randomly locking, whether driving or not. Now, I have to keep clips on the belts to prevent them from fully retracting. *Js

Filed Incident Seat beltsNHTSA 10545105
Seats & seat belts

On 6/18/13, I noticed that the driver's seat latch (the receptacle portion) was being pushed between the seat and the center console when I attempted to buckle. The fourth or fifth time it did this, the entire buckle broke off. Upon inspection, the wire cable connecting the seat belt latch and the anchor had broken. The anchor was still securely bolted to the seat. I have contacted a dealer and chrysler, to no avail. *Tr

Filed Incident Seat beltsNHTSA 10520540
Seats & seat belts

The following problem concerns the seatbelt restraint system ".The seatbelt control module" has failed on our 2000 chrysler sebring 1. This vehicle is not driven on a regular basis and after setting for a period of time the battery was low requiring jump starting. 2. Two dealerships checked out what was draining the battery and was told there was no problems with the car. 3. With the battery ground disconnected and an ammeter between battery ground and chasis ground my initial reading was .06 Amps,. 4....

Read the full complaint

With this same test setup in place the doors were opened and then closed the ammeter read .5 Amps draw on the battery after the control for the interior lights timed out. Note:the initial breaking of the ground disguised the problem. (Maybe why dealerships did not detect the problem) . I proceeded to pull fuses until I discovered the .5 Amp drain went away when the fuse feeding the seat belt control module was pulled. I have not yet had our car repaired however appearances are that the module is defective. This problem may never have showed up had the car been driven on a regular basis keeping the battery from getting too low to start the car. Even with the fuse pulled the seatbelts could be used as normal which we did several times before they locked to where they could not be retracted. What little research I have done tells me this module has many safety functions besides just reminding us to fasten the seat belts. The impact sensor is a component of the seatbelt control timer module (sctm) located under the center console. The g-sensor is sensitive to frontal impact and to a roll or pitch or more than 45 degrees and to acceleration or deceleration equal to or greater than 0.7G in any direction. In closing my concern is that there are many cars being driven daily with the owners unaware of a malfunctioning "seat belt control module". *Tr

Filed Incident Seat beltsNHTSA 10455270
Seats & seat belts

Tl* the contact owns a 2000 chrysler sebring convertible. The contact stated that the driver and passenger side seat belts were locked and would not retract. The vehicle was not taken to the dealer. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was 154,000 and the current mileage was 157,000.

Filed Incident Seat beltsNHTSA 10447195
Seats & seat belts

My wife owns a 2000 chrysler sebring jxi convertible. On september 6., 2011 My wife was leaving for work and when she went to buckle her seat belt the entire seat belt's female recepticle (driver's side) broke off in her hand (the entire cable snapped). Upon inspection we discovered the cable that bolts the recepticle to the seat frame had broken in the middle where there is very little binding or bending. We called chrysler customer service and they stated it "wasn't covered under warranty...." My wife took the...

Read the full complaint

vehicle to our local chrysler dealership and they told her it would cost $300 to replace it. As a temporary fix I moved the seat belt recepticle from the front passenger side seat to the to the driver's side since it's illegal in missouri to drive without a seat belt. We feel there shouldn't be a warranty period for safety equipment on a vehicle - if a part fails through no fault of the owner the manufacturer should replace their substandard parts, especially when it's a defective part that could cost the occupants of the vehicle their life. After doing an online search we found we weren't alone in seat belt recepticles breaking on chrysler sebrings. Within 10 minutes of my search I found 5 complaints describing the same malfunction or defect - one mentioned the problem was discovered after an accident where "severe head injuries" resulted. The complaints I read online started with the model year 2000 and go through 2005. My wife is afraid to drive the car for fear of the seat belt recepticle I moved to the driver's side failing in an accident. If I get one from a junkyard to save money on the repair who's to say it won't break in an accident too resulting in serious injury or death? *Tt

Filed Incident Seat beltsNHTSA 10425899
Seats & seat belts

Tl* the contact owns a 2000 chrysler sebring convertible. The contact stated that at times, the seat belt connectors would fail to align properly, rendering them inoperable. The vehicle was taken to an authorized dealer and the manufacturer was notified. The vehicle was not repaired. The failure mileage was 160,000 and the current mileage was 164,000. Updated 8/29/11 *cn the seat belt release module does not randomly belts. Updated 09/21/11

Filed Incident Seat beltsNHTSA 10416766
Electrical system

Tl*the contact owns a 2000 chrysler sebring. The contact stated that while trying to start the vehicle, the key would not turn in the ignition switch. The contact has taken the vehicle to the dealer whenever the failure occurred sporadically for the last five years. The contact had not allowed the dealer to diagnose the failure with the ignition switch. The contact was using home remedies to diagnose the failure; however, it was unsuccessful. The contact stated this was a safety issue because the vehicle could leave him stranded on the road. The failure mileage was 40,000.

Filed Incident Electrical systemNHTSA 10359258
Body, doors & structureEquipment & accessories

Tl*the contact owns a 2000 chrysler sebring convertible. The contact stated that the button to the convertible top would not work unless it were pressed repeatedly. The contact also stated that the air conditioning unit stopped functioning. The vehicle was taken to an independent mechanic where the contact was told that the compressor to the air conditioning unit failed; yet, they were not sure what was wrong with the convertible top. The vehicle was not repaired. The failure mileage was 34,000 and the current mileage was 53,000. The vin was unavailable.

Filed Incident Structure · EquipmentNHTSA 10341226
Seats & seat belts

2000 Chrysler sebring convertible jxi - seatbelts malfunction seatbelt retractor locks up (both seats at the same time) so the seat belts cannot be used. Intermittent problem but very problematic. I have replaced the seatbelt fuse. I have consulted with a chrysler service dept. Technician who stated that replacing the retractor would be $508 per seat but couldn't guarantee that this would be the solution. I have researched the internet; http://townhall-talk.Edmunds.Com/direct/view/.F11c283 which has numerous similar complaints and www.Allexperts.Com. *Tr

Filed Incident Seat beltsNHTSA 10336486
Seats & seat belts

I own a 2000 chrysler sebring convertible jxi. The seat belts occasionally will not retract from both front seat. The problem persists for anywhere between an hour and several days. Both front seat belts lock at the same time. *Tr

Filed Incident Seat beltsNHTSA 10334793
Brakes

I was just driving my chrysler sebring 2000 this afternoon when the brakes failed completely. I was lucky to be in a parking lot when this happened and I don't want to imagine what would have happened on a highway! There was no warning at all, no light coming on, nothing, and the brake pedal just collapsed completely. I will have to take the car to the garage on tuesday. I wanted to know what I can do about that to be sure this does not happen again....It's scary to think that you can drive a car 65 miles an hour with suddenly no brakes at all!! I was just very lucky this time! *Tr

Filed Incident Service brakes, hydraulicNHTSA 10333849
Engine & coolingFire

Letter from senator isakson on behalf of re her 2000 chrysler sebring that burst into flames under the hood *tgw

Filed Incident Engine and engine coolingNHTSA 10331733
Electrical systemAirbags

I have a 2001 chrysler sebring convertible with exactly the same problem: the horn goes off whenever it wants to. The first time it completely burned out both of the horns, which I had to pay for to be replaced, since the vehicle was long out of warranty. Of course, the horn always activated itself in the middle of the night. The chrysler dealer diagnosis revealed that the horn switch is somehow defective, something I figure out after banging on the pad during one scenario only to discover this caused the horn to...

Read the full complaint

turn off. The horn switch is designed as some sort of membrane and is non-conventional by any means. Temperature expansion and contraction causes the two side of the switch to connect on their own. To add insult to injury, you can only replace the switch if you replace the entire airbag assembly, a part which is quite costly. So, instead of paying the over one grand repair cost for something that is obviously a manufacturing defect, I wired in a switch to the side dash fuse compartment in between the horn relay and the connector and mounted the switch in the center of the panel door. Now, when I leave the vehicle, I simply throw the switch and my horn worries are over. A hassle? Maybe, but at least I don't have to run out to the car in my underwear in the middle of the night to tap the steering wheel pad to stop that infernal blaring of the horn. This should have been a recall by chrysler--which it never was--as the switch design is defective. Slipshod engineering is my analysis. Chrysler should be liable for the repairs but they assume no responsibility, probably because this model has so many electrical, computer, and alarm issues that they would have gone broke fixing all of them. My dash lights go on and off at random and I'm also having alarm and key fob issues. I really love my convertible, but I'll never buy another chrysler product. *Tr

Filed Incident Electrical system · Air bagsNHTSA 10286033
Seats & seat belts

Tl* the contact owns a 2000 chrysler sebring jxi. The contact stated that the webbing of the passenger front seat belt could not be extracted when worn by an occupant. If the occupants are not secured in the vehicle, they could be seriously injured in the event of a crash. The vehicle was taken to a dealer, in which the technicians have replaced the wiring harness, seat belt buckle, and seat belt retractor. The repairs have not remedied the failure. The failure mileage was 70,000 and the current mileage was 75,000. Updated 10/21/09. *Lj updated 10/23/09.*Jb

Filed Incident Seat beltsNHTSA 10283666
Seats & seat belts

I have a 2000 sebring jxi convertible. The drivers side seat belt base wires broke and tore off the click in part.. I brought it to chrysler dealership where I purchased the car and they said they wouldn't replace it. They were going to charge me over $300.00 Dollars to put in a new base. My husband transferred the passengerside base to the drivers side for me. But I can't take anyone with me in the car. I am still upset. I wish they would send me a new base. *Tr

Filed Incident Seat beltsNHTSA 10274827

Chrysler Sebring Convertible: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
20040200-B
20030300-C
20020300-C
20010300-C
200078232Seats & seat beltsF
199991392Transmission & drivetrainF
199852331SuspensionF
19970300-C
19960300-C
All Sebring Convertible years

2000 Chrysler Sebring Convertible vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2000 Chrysler Sebring Convertible? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2000 Chrysler Sebring Convertible

Does the 2000 Chrysler Sebring Convertible have any recalls?

Yes - NHTSA lists 2 recalls for the 2000 Chrysler Sebring Convertible: lower arm (December 2010); lower ball joint (October 2009). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2000 Chrysler Sebring Convertible?

By the complaints owners filed with NHTSA, the most common problem areas are the seats & seat belts (27), brakes (11), electrical system (8).

How many complaints has the 2000 Chrysler Sebring Convertible had?

78 complaints have been filed with NHTSA, the first on August 10, 2000 and the latest on January 23, 2018. Of these, 3 describe a crash and 2 a fire, and together they report 5 injuries and 0 deaths.

Is the 2000 Chrysler Sebring Convertible a reliable vehicle?

Its Safety Index is 2 out of 100 (grade F: far more problems than a typical Chrysler Sebring Convertible year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Chrysler Sebring Convertible years have the most complaints?
What should I do if my 2000 Chrysler Sebring Convertible has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience