- The problem
- Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
- The risk
- These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
- The fix
- Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Vehicle safety record
2008 Dodge Ram 2500 Problems, complaints & recalls
Owners have filed 342 complaints about the 2008 Dodge Ram 2500 with NHTSA, most often about the steering (181) and the suspension (49). Those complaints describe 16 crashes, 9 fires and 10 injuries. It is covered by 9 recalls, the latest in May 2016 for the inflator module. For comparison, the 2007 has 361 and the 2009 has 223.
NHTSA data checked
FFar more problems than a typical Ram 2500 year, for its age
#50 most complained-about 2008 vehicle
- Complaints
- 342
- Recalls
- 9
- Crashes
- 16
- Fires
- 9
- Injuries
- 10
- Deaths
- 0
Most common 2008 Dodge Ram 2500 problems
Share of all 342 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2008 Dodge Ram 2500 recalls 9
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
- The risk
- In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
- The fix
- Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.
- The problem
- Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.
- The risk
- A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.
- The fix
- Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.
- The problem
- Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.
- The risk
- A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.
- The fix
- Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.
- The problem
- Chrysler is recalling certain model year 2008-2011 dodge ram 2500/3500 4x4, manufactured from february 14, 2008, through march 28, 2011; model year 2008-2011 dodge ram 3500 cab chassis 4x2, manufactured from february 14, 2008, through march 28, 2011; and model year 2008 dodge ram 1500 mega cab 4x4, manufactured from february 14, 2008, through august 15, 2008, because the left tie rod ball stud may fracture. This condition tends to occur during low speed parking lot type maneuvers when the customer is making a tight turn. Additionally, model year 2003-2008 dodge ram 2500/3500 vehicles may have received the affected tie rod assembly as a replacement part during normal service.
- The risk
- This condition could result in the potential loss of directional stability in the left hand front wheel, increasing the risk of a crash.
- The fix
- Dealers will inspect the tie rod ends for relative orientation and replace the left outer tie rod as required and perform a front end toe alignment as needed. This service will be performed free of charge. The safety recall began on october 3, 2011. Owners may contact chrysler at 1-800-853-1403.
- The problem
- Fabtech is recalling certain aftermarket replacement pitman arms, p/nos. Fts93001 and ft44039, installed for use on certain 2003 through 2008 dodge 2500 4wd, 3500 4wd, and 1500 4wd mega cab vehicles. The pitman arm can fracture and break away from the steering box causing total loss of steering control.
- The risk
- Steering loss could result in a vehicle crash possibly resulting in property damage, injury or death.
- The fix
- Fabtech will notify owners and authorized installers will inspect for defective pitman arm and replace if necessary free of charge. The safety recall began on may 24, 2010. Owners may contact fabtech at 1-877-432-2832.
- The problem
- Chrysler is recalling 32,782 my 2008-2009 dodge ram 2500, 3500 and 3500 cab chassis pickup trucks equipped with powers and sons steering linkage. The steering linkage drag link inner tie rod to pitman arm ball stud may fracture. Also the steering linkage damper attaching the bracket may yield and shift on the linkage.
- The risk
- This could result in a loss of steering control and the restricted ability to turn the vehicle in one direction increasing the risk of a crash without warning.
- The fix
- Dealers will replace the steering linkage drag link inner tie rod end assembly, and inspect the steering linkage damper bracket free of charge. The recall is expected to begin on or before february 16, 2009. Owners may contact chrysler at 1-800-853-1403.
- The problem
- Chrysler is recalling 108,429 my 2007-2008 dodge ram 2500 and 3500 pickup trucks equipped with 6.7L diesel engines. A silencer pad can sag and contact the exhaust gas recirculation (egr) cooler.
- The risk
- THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE.
- The fix
- Dealers will add a bracket to support the engine compartment silencer pad adjacent to the egr cooler. The recall is expected to begin during december 2008. Owners may contact chrysler at 1-800-853-1403.
- The problem
- Certain curved tempered replacement glass manufactured by hangzhou safety glass ltd and supplied to safelite by auto temp inc., Identified as dot-430, and sold for use on certain domestic and foreign vehicles may not break into small pieces as expected of tempered glass and fails to conform to federal motor vehicle safety standard no. 205, "Glazing materials."
- The risk
- In the event of a vehicle crash, the occupant(s) may be seriously injured by shattered glass.
- The fix
- Safelite will notify its retail customers and replace the glass free of charge. Retail customers can contact safelite toll free at 1-888-843-2906. Safelite will notify its wholesale customers and reimburse wholesale customers for current inventory and at a specified rate for replacing their customer's glass. Wholesale customers can contact safelite's wholesale division, service autoglass toll free at 1-888-246-6298. The recall began on january 15, 2008.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
342 complaints about the 2008 Dodge Ram 2500
Newest first, as filed with NHTSA by owners. Page 1 of 14.
driving down the highway at 70 mph and the drivers door came opened it was caused by a faulty door lock actuator
I want to apologize for the lengthy description but I feel this is quite possibly the most critical area to not be vague in. **This problem occurs every time, NOT an intermittent condition.** REAR SEAT/CENTER SEAT BELT RETRACTOR; will not extend out from the retractor. The belt is locked in the fully retracted (unoccupied) position. The vehicle can be on a flat surface, an incline, or a declined position when this occurs. There's nothing obstructing any part of the belt and retractor. In order to use that...
Read the full complaint
position/seat belt, I must repeatedly (sometimes in excess of 20 times) pull the belt in different rates of speed ie. pull the belt very slowly, pull it normally, pull it very fast by basically snatching the belt. I've even tried to help the belt further retract into the retractor by slowly feeding the belt rearward. There's no 1 action that seems to work better than the other. Furthermore, at times, the belt (once able to be used) will not hold its position to keep the occupant from moving forward in a panic stop or even by snatching the belt to check its operation. The buckle does function as designed so this problem is strictly related to the shoulder belt not keeping the occupant secure. Apon visual inspection, there are no noted frays, stains, foreign objects, or signs of attempted (prior) repairs. I also want to note that I am an ASE certified Master Mechanic so I am well versed on the operation, diagnosis and replacement of seat belts/retractors/sinchers buckets etc. I'm asking for assistance by any information you can share with me to remedy this issue. This is my "daily driver" routinely using the back seat for my children. I don't want to replace it with a used part because I believe this is a common issue for this platform vehicle. Thank you for your time and assistance!
The contact owns a 2008 Dodge Ram 2500. The contact stated while driving various speeds, he started to smell exhaust fumes inside the cabin of the vehicle. The contact stated no warning light was illuminated. The vehicle was not diagnosed or repaired. A dealer was not contacted. The manufacturer had not been informed of the failure. The failure mileage was approximately 162,000.
The contact owns a 2008 Dodge Ram 1500. The contact stated that he heard an abnormal noise in the front driver's side wheel. No warning lights were illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the wheel bearing failed and needed to be replaced. The vehicle was repaired however, the failure recurred. The contact stated that while driving at approximately 30-35 MPH making a left turn, the front driver's side wheel detached from the wheel bearing. As a result, the vehicle...
Read the full complaint
started to spark and dragged into the concrete of the street. No injuries were sustained. No medical assistance was required. The contact was unsure if a police report was filed. The vehicle was towed to an independent mechanic where it was diagnosed that the driver's side brake line and wheel bearing failed and needed to be replaced. The vehicle was repaired. The dealer and the manufacturer were notified of the failure and the contact was informed that the VIN was not included in a recall, but no further assistance was provided. The failure mileage was approximately 186,000.
The contact owns a 2008 Dodge Ram 3500. The contact received notification of NHTSA Campaign Number: 13V529000 (Steering) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
The contact owns a 2008 Dodge Ram 2500. The contact stated the engine warning light was illuminated. The contact took the vehicle to a certified mechanic who stated the sensor needed to be replaced as well as the harness. The vehicle had not been repaired due to the parts being on back order. The manufacturer was not made aware of the failure. The approximate failure mileage was 70,000
The contact owns a 2008 Ram 1500. The contact stated while driving approximately 5 MPH, a loud booming noise suddenly occurred from the rear of the vehicle and the rear wheels locked up. The vehicle was towed to the residence and inspected by an independent mechanic who diagnosed that the rear differential was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer and local dealer were not notified of the failure. The approximate failure mileage was 86,000.
during cold weather - when outside temp is below 30 degrees the wipers will not work. When outside temp is above 30 degrees wipers work. During a snow storm, driving home the wipers stop working and windshield freezes up. I replaced the multifunction switch and the wiper motor and dealer stated that the totally integrated power module could be bad. there is so many complaints about others having this issue. This is a major safety issue. Something needs to be done before someone is killed.
While driving the vehicle suddenly lost engine power and turned off. When this happened the steering column locked. It did not just loose power steering. The column itself entirely locked up. At this point the vehicle had no steering and limited breaking and went off the road. Thankfully it just went into a ditch and no damage was done. The vehicle turned right back on. The next day I recreated the problem on some friends property. I gave the keys in the ignition a small tug and the engine would stop and the...
Read the full complaint
steering column would lock. The ignition never rotated out of the on position and the key remained in the ignition. I recreated this probably 5 times and it did the same thing every time. I then brought it to the dealer but they didn't have the parts to repair it so I didn't have them look at it. I had to use the vehicle sooner then they could repair it to pull a camper about 1200 miles. I diagnosed the problem to be the ignition switch. I replaced the switch myself and the vehicle has not had the same problem since. I have given the keys in the ignition the same kind of tug and it is no longer a problem. I do have the switch available for inspection. I personally can totally understand the engine turning off due to an ignition switch failure but I believe the actual steering column locking is unacceptable.
The contact owns a 2008 Dodge Ram 2500. The contact stated while exiting out of the garage, the windshield defroster was activated and there was a loud clicking sound coming from the HVAC system. The contact stated that the HVAC system failed to switch over to the air vents. The contact inspected the vehicle and became aware that the defroster actuator was cracked inside in the vents causing the failure. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 109,000.
The contact owns a 2008 Dodge Ram. The contact stated that the rocker panels, subframe, truck bed, and oil pan were severely rusted. The cause of the failure was not yet determined. The local dealer and manufacturer were not notified of the failure. The failure mileage was 116,000.
Tl* the contact owns a 2008 dodge ram 2500. The contact stated while driving 4 mph, he heard an abnormal sound coming from the vehicle. The contact stated no warning light was illuminated. The contact stated that he attempted to steer to the vehicle to the right however, the vehicle failed to respond. The vehicle was stopped in the middle of the roadway. The vehicle was not drivable. The vehicle was towed to his residence. The contact called colorado springs dodge (7455 austin bluffs pkwy, colorado springs, co...
Read the full complaint
80923, (719)475-8550) and the dealer was made aware of the failure. The vehicle was not diagnosed nor repaired. Upon investigation, the contact associated the failure with nhtsa campaign number: 13v529000 (steering) however, the vin was not included. The manufacturer had not been informed of the failure. The failure mileage was approximately 289,000.
I was driving on i405 in washington state traveling southbound when I noticed smoke coming from my engine compartment...I pulled over popped the hood and took a quick look.. I noticed flames on the lower portion of the motor almost behind the firewall...Called 911...
The brake lights come on themselves when the truck is completely off. It's intermittent however it does it frequently enough to drain the battery. The engine light comes on as well however it does not provide a code to determine the cause of the issue.
Brake light and turn signals do not work even after replacing bulbs, bulb sockets and multifunction turn signal switch
Wiper assembly came apart at 55 miles an hour on the highway in the rain almost wrecked my vehicle.
Tl* the contact owns a 2008 dodge ram 2500. While driving 60 mph, the vehicle hesitated, lost power, failed to accelerate, and stalled. Also, the check engine warning indicator illuminated. The vehicle was pulled over to the side of the road and failed to restart. The contact stated that code: p1451 appeared. The failure recurred five times and the vehicle was towed to smolich motors (1865 ne hwy 20, bend, or 97701, (541) 389-1177). The dealer diagnosed that the diesel particulate filter tracked soot from the...
Read the full complaint
exhaust and the lower particulate emission system failed. The vehicle was repaired. A month later, the turbo system failed and was repaired by a diesel independent mechanic. The manufacturer was made aware of the failures and did not assist. The approximate failure mileage was 151,000.
Transmission burned up and caused the truck to catch fire due to improper dipstick fit. Fluid spewed onto the turbo and started fire. Burnt stuff up pretty bad.
Death wobbles: I have replaced upper and lower ball joints with problem solvers. Replaced the tie rods and ends. Replaced the stabilizer shock, replaced the track bar rubber bushings, replaced the otter universal joints on the aam 9.50 14 Bolt electric hubs. New shocks all around. Drove to salt lake city and the death wobbles came back have to pull off the hwy and come to a stop while it is shaking the truck apart. 15 Times from idaho.. This is a major safety problem the steering box has problems and it is not...
Read the full complaint
listed under any recalls. New alignment also. New transmission, at 163,000 boiled over onto the turbo, the dipstick never fit in the tube and fluid caused the truck to catch fire. 3 Years ago.
The bracket that hold the break line to the rear end (axle) had rubbed the metal break line until it wore through the line and then split causing brake fluid to leak out (fast). I noticed my break peddle start going to the floor, I was driving on the highway when I pushed the break peddle to slow down because there was a speed zone ahead, the break peddle went to the floor. That's when the e break warning light came on notifying me that my break fluid was low or empty. I have a manual transmission so I was able to...
Read the full complaint
shift down to slow down, even though I was still trying to use my brakes the peddle would to the floor, stopping was 90% gone, I had to use my e brake to come to a complete stop.. When I stop the vehicle that's when I looked underneath the truck and noticed a large puddle of break fluid, I could also see a stream of fluid where I pulled in at. So it was spraying out when I was using the breaks to slow down and stop. When I got home I looked where truck is always parked there no fluid had been leaked there. Between my home and the 36 miles to town it had the bracket had rubbed through and split the break line. My mechanic stated that the bracket had been rubbing the brake line for a while to split open like that. I had to replace the metal brake line that went to the rear passenger brake. Now I'm worried that this might happened to my other brake lines. It never states that I'm to check for wearing on metal lines. Nothing after market has been done to this vehicle it's 100% stock as it was when bought from the dealership. To me this a serious problem that could have lead to an accident which could kill or hurt a person/people. This is a factory default and needs to be addressed immediately! A simple rubber protect piece needs to be place on the bracket and/or line to protect this from happening again!!
Steering death wobble can control steering motor broke piston connection rod because exhaust manifold works or does something break bolts in bead causing tick then valve seat drop so valve drop to piston pistion hit valve broke connection rod now dodge wants $ 5,000 to fix what I had no control over it breaking on many trucks and didnt fix so there wanting me to fix there messed up faulty parts then everything it messed up to I ain't got 500 to spend extra let alone $5,000 minimum for dodge mainifold breaking and...
Read the full complaint
messing up my wholeotor I demand help my truck ain't 10 years old this is not on recall list but keeps happening to a dodge trucks I have 2008 ram 2500 3x4 crew cab have all my manitinece recipets I want I demand help for this faulty part luckly vehicle and killed someone we spent a lot of money for truck I want help fixing it now
My vehicle has repeatedly experienced severe shaking of the front end while traveling at speeds of 65 to 70 mph after hitting a bump such as the transition of a bridge approach slab. I have had the recall check of the tie-rod, and have even tried a beefier tie rod with bracing. The only way to stop the violent shaking is to slow to less than 40 mph. I know this has been a repeated experience of dodge ram drivers based on forum discussions. I have had 2 sets of ball joints replaced as a result of the violent...
Read the full complaint
shaking. This last time this occurred, I was with my wife traveling to the coast. The shaking was so severe, we nearly hit a guard rail. I can't hardly believe that dodge has designed such a fatal flaw into a vehicle.
Cold air blowing from driver side only, while passenger side blowing warm when set on heater mode. :( Problem still happening , most dissapointing as I just bought this used vehicle, and we're beginning winter weather.
I was going 65 miles per hour on the freeway when my truck violently shake back and forth so hard I had to come to a complete stop to get it to stop. I've had the front suspension replaced 3 times in the past year and still have what they call a death wobble. I have spent so much money on rentals and on shop repairs trying to repair this problem and still cannot go over 40 miles an hour without it violently shaking. This is dangerous to my family it could kill somebody and I think dodge should be responsible for...
Read the full complaint
taking action on repairing this or figure out the problem . I have called dodge and they have told me it is not a recall so they cannot help me out. I had bought brand new tires a brand new drive line along with replacing the front suspension 3 times now and I still cannot drive my truck without it causing violent shaking. It has 87,000 miles on it has never been in an accident so I cannot figure out why this started happening but I think that it should not be okay to have this truck on the road it's going to hurt somebody.I have only driven a couple of times and spent alot on rentals .I will never in my life buy another dodge due to lack of concern for my family's saftey.I own this vehicle outright and wish I would have never bought it.Thats how scary it is to drive.
Tl* the contact owns a 2008 dodge ram 2500. The contact took the vehicle to autonation chrysler dodge jeep southwest (7980 w tufts ave, littleton, co 80123) to be repaired per an unknown recall regarding the air bags. The contact examined the vehicle and believed that the air bags were not replaced. The vin was researched on safercar.Gov, but no open recalls were found. The manufacturer had not been contacted. The vehicle was not taken back to the dealer. The failure mileage was 181,086.
Dodge Ram 2500: every year compared
All Ram 2500 years2008 Dodge Ram 2500 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2008 Dodge Ram 2500 | 342 | 9 | F | |
| 2008 Ram 3500 | 4 | 1 | A | Compare |
| 2008 Dodge Ram 3500 | 0 | 11 | B | Compare |
| 2008 Ford F-250 | 0 | 6 | C | Compare |
| 2008 Ford F-350 | 0 | 7 | D | Compare |
| 2008 Chevrolet Silverado 2500 | 0 | 4 | C | Compare |
| 2008 Chevrolet Silverado 3500 | 0 | 4 | C | Compare |
| 2008 GMC Sierra 2500 | 0 | 3 | B | Compare |
| 2008 Dodge Grand Caravan | 1,293 | 8 | F | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2008 Dodge Ram 2500
Does the 2008 Dodge Ram 2500 have any recalls?
Yes - NHTSA lists 9 recalls for the 2008 Dodge Ram 2500: inflator module (May 2016); inflator module (May 2015); tie rod assembly (November 2013); tie rod assembly (November 2013) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2008 Dodge Ram 2500?
By the complaints owners filed with NHTSA, the most common problem areas are the steering (181), suspension (49), engine & cooling (43).
How many complaints has the 2008 Dodge Ram 2500 had?
342 complaints have been filed with NHTSA, the first on January 22, 2008 and the latest on December 11, 2024. Of these, 16 describe a crash and 9 a fire, and together they report 10 injuries and 0 deaths.
Is the 2008 Dodge Ram 2500 a reliable vehicle?
Its Safety Index is 24 out of 100 (grade F: far more problems than a typical Dodge Ram 2500 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Dodge Ram 2500 years have the most complaints?
2006 (670), 2003 (661), 2004 (582). See every Dodge Ram 2500 year compared.
What should I do if my 2008 Dodge Ram 2500 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data