Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Driver assistance

2021 Ford Bronco Driver Assist problems

Owners have filed 30 complaints about the 2021 Ford Bronco's driver assistance with NHTSA - 13% of all its complaints, most recently on August 20, 2026. They describe 3 crashes, 0 fires and 3 injuries. Phantom braking, automatic emergency braking, lane keeping, blind spot and collision warnings.

Complaints
30
Recalls
8
Crashes
3
Fires
0
Injuries
3
Deaths
0

Driver Assist recalls for the 2021 Ford Bronco

Back over prevention: software

26V124000849,310 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
The risk
A rearview camera that fails to display an image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
The fix
The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.

Back over prevention: camera

25V88800035 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
The risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
The fix
Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026.

Back over prevention: software

25V3150001,076,138 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
The risk
A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
The fix
The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.

Back over prevention: camera

25V31200012,219 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
The risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
The fix
Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14.

Back over prevention: camera

23V598000177,402 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2020-2023 Lincoln Aviator, 2018-2021 Lincoln Navigator, 2022-2023 Ford Transit, and 2021 Ford Bronco vehicles. The rearview camera, or 360-degree view camera if equipped, may not display a rearview image when the vehicle is placed in reverse.
The risk
Loss of the rearview camera image can reduce the driver's rear visibility, increasing the risk of a crash.
The fix
Dealers will replace the rearview camera, and update the software and wiring as necessary, free of charge. Owner notification letters were mailed November 20, 2023 to Lincoln owners. Ford vehicle owners notification letters were mailed March 4, 2024. Ford remedy parts are anticipated 2nd Quarter 2024. Ford's number for this recall is 23S48.

Back over prevention: camera

23V1650001,651 vehicles affected

Over-the-air fix
The problem
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
The risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
The fix
The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05.

Back over prevention: camera

22V82500047,046 vehicles affected

Over-the-air fix
The problem
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
The risk
A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
The fix
The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27.

Forward collision avoidance: radar

21V982000839 vehicles affected

The problem
Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.
The risk
A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash.
The fix
Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52.

Driver Assist complaints

Acceleration & cruise controlDriver assistance

The contact owns a 2021 Ford Bronco. The contact stated that while driving at an undisclosed speed, the vehicle jerked and lost motive power. No warning light was illuminated. Additionally, the vehicle experienced unintended acceleration while driving. The lane departure feature also steered the vehicle in the opposite direction while there was construction on the road. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 68,000. The VIN was not available.

Filed Incident Vehicle speed control · Lane departureNHTSA 11758268
AirbagsDriver assistanceCrash

I was driving in the northbound left hand lane on creasy lane in Lafayette, Indiana, approaching Rome Drive. A driver from a side street took an illegal left hand turn to head towards the northbound lanes of creasy lane, I was traveling over 30 mph, maybe 40 at the time of the collision. I was unable to see the other driver until it was too late as they passed by drivers turning from the right hand lane onto the side road they had been at. My airbags did not deploy during the collision, nor did my pre collision...

Read the full complaint

assist alert nor did my brake system engage. I suffered extensive front end damage at the time of the incident. There was a previous recall for my airbags in this vehicle, as well as notifications in 2024 that my collision systems had been disengage during warranty work.

Filed Incident Air bags · Forward collision avoidanceNHTSA 11746859
Electrical systemDriver assistance

The digital gauge cluster where it shows sensitive information is a blacked out screen. I took it an automotive shop to investigate the issue. They ran a diagnositic and confirmed the screen is receiving power, fuses are good, but the screen is not powering up. I cannot view the digital speed, fuel gauge, mileage, access GOAT modes, view tire pressure, view oil life, and other critical data, etc. This first occured a few months ago and would randomly turn back on, but not the screen is black more than it is on. Luckily I am able to track the fuel gauge (miles to empty) on the infotainment screen.

Filed Incident Electrical system · Forward collision avoidanceNHTSA 11733378
Seats & seat beltsFuel systemDriver assistance

3 separate safety-related components have failed on my 2021 Ford Bronco, all of which correspond to open federal safety recalls that remain unremedied: 1. Infotainment/APIM Module & Backup Camera System (Recall Campaign 26V124): my infotainment screen fails to turn on, particularly in high-temperature conditions. When this occurs, the rearview/backup camera is completely non-functional. The vehicle displays no image when in reverse gear, eliminating all camera-assisted visibility behind the vehicle. This directly...

Read the full complaint

matches the conditions described in Recall 26V124, issued March 4, 2026. No remedy has been provided. 2. Digital Instrument Cluster / Dashboard: my digital dashboard intermittently fails to illuminate at vehicle startup. This occurs randomly and without warning. When it fails, the driver cannot see critical safety information including current speed, fuel level, engine temperature, or any warning indicators. Video documentation of this failure exists. This component is available for inspection upon request. 3. Low Pressure Fuel Pump (Recall Campaign 25V455): my vehicle has stalled on multiple occasions while in motion. During stall events, all dashboard warning lights illuminate simultaneously. This is consistent with the fuel delivery failure described in Recall 25V455, issued July 8, 2025, which states the fuel pump can fail causing loss of fuel pressure and an engine stall while driving. No remedy has been provided since the recall was issued in July 2025 (~9 months ago). All components are available for inspection upon request. However, the authorized Ford dealership in the area has refused to accept the vehicle for service or inspection, citing parts unavailability. Engine stall while in motion. my vehicle has stalled multiple times while being driven. The driver works as a real estate agent and regularly transports clients in this vehicle. The engine has stalled with passengers present. A sudden engine stall while driving results in immediat

Filed Incident Seats · Fuel / propulsion system · Back over preventionNHTSA 11731872
Driver assistance

My BLIS module on the passenger side does not work and I have a constant warning light displayed that there is a system malfunction. Under further investigation, this is a KNOWN design issue caused by the rear wiring harness that contains the BLIS sensor rubbing against components in the rear bumper. My vehicle has 31000 miles on it and is now out of warranty. Ford dealers are aware of this issue but claim it is not a recall and not under warranty. This is a safety issue.

Filed Incident Lane departureNHTSA 11724615
Driver assistance

The wiring harness is rubbing against the bumper, causing it to wear and eventually cut through. This causes an error to my BSM/Cross Traffic alert. I have an extended warranty, but it doesn't cover it. This is a problem I have seen on the Bronco6G forums.

Filed Incident Lane departure · Back over preventionNHTSA 11715858
Driver assistance

While driving I lost most/all ADAS system. I received several alerts that kept repopulating. No Cross Traffic working No Blind Sport working No Cruise Control No Forward Collision working No Lane Departure working I took the rear assembly by the taillight and rear bumper. The wires and electrical components are corroded. Koons Ford Annapolis Maryland is requiring $1520 parts and labor.. This is a major safety problem as it was not designed correctly. Many Bronco Owners are going through this..

Filed Incident Forward collision avoidance · Lane departure · Back over preventionNHTSA 11712374
Electrical systemDriver assistance

I received an alert on the dash stating there was an issue with the blind spot monitoring/rear cross traffic system. It was erroring off and on for that entire drive. When I got home, I googled the issue and it appears it's a known issue with '21 and some early '22 broncos where they factory installed the blind spot module wiring harness too close to the rear bumper. Over time, the wires rub and eventually rub bare and corrode or short out. I went out to take a look and sure enough, I had rubbed through on the...

Read the full complaint

driver side (photo) and the passenger side was nearly rubbed through. I have an extended warranty and it's at the dealership today. This is a manufacturing defect and should be covered (even if out of warranty) in my opinion. We will see what kind of story the dealer can come up with to wiggle out of it being covered under warranty.

Filed Incident Electrical system · Lane departure · Back over preventionNHTSA 11712311
Electrical systemDriver assistance

Bronco wire corrosion cross traffic refers to a known issue where wiring under the rear bumper, often for the blind spot/cross-traffic sensors, chafes, frays, and corrodes, causing system faults and failures, sometimes due to design flaws or environmental exposure to salt, requiring inspection and repair of the harness. This problem triggers error messages like "Cross Traffic System/Blind Spot System Fault" in the instrument cluster, impacting safety features, with potential fixes involving harness repair, protective sheathing, or sensor replacement. My car's wiring was corroded due to this flaw and required a repair exceeding $1,000.

Filed Incident Electrical system · Back over preventionNHTSA 11711629
Electrical systemDriver assistance

Location of wiring from the factory for Blind Spot Warning and Cross Traffic Alert systems is not protected. The wiring has frayed and broken due to the wiring being unprotected, loose and rubbing on the rear bumper, causing the systems to not function. This is a blatant design defect from the factory, causing two safety systems to fail. Reporting now as, to the best of my knowledge, the manufacturer has not issued a TSB or recall and dealerships have acknowledged the issue.

Filed Incident Electrical system · Lane departure · Back over preventionNHTSA 11706454
Driver assistance

rear view camera display when vehicle is in reverse will intermittently turn blue or black which renders the rear view camera useless. and at times will state camera unavailable. vehicle is a 2021 ford bronco built on june 15, 2021 at ford Michigan build plant. i have contacted ford related to this concern as i believe that the vehicle should fall under recall 23s48 for rear camera replacement, and 25s49 for module updates related to rear camera display. the vehicle year, build date, assembly plant and symptoms...

Read the full complaint

all fit within the parameters of recall. note that i also have a 2022 bronco that these recalls are active on for the same concerns, the concern happens 7-8 times a week for the last 4-5 months. dealership has contacted ford sssc team about getting recalls activated on this vehicle and they are given the most basic responses stating that this vehicle is not included due to "certain model year vehicles" even though the vehicle is clearly within the model years outlined in both recalls. the rear view camera intermittently not working is a safety issue as it can stop working at any time when you would be using it to reverse. thank you for your time and consideration when investigating this concen.

Filed Incident Back over preventionNHTSA 11688956
Electrical systemDriver assistance

I have been getting a message that my blind spot and cross traffic alert deactivated because trailer is attached. I have never had a trailer attached but do have a trailer hitch- the dealer said Ford refuses to pay to have it fixed because the bumper to bumper warranty is out. the car has been garaged and has only 9,000 miles on it. This is a safety issue that I think they should cover as I have no blind spot or cross traffic warnings.

Filed Incident Electrical system · Lane departure · Back over preventionNHTSA 11683687
Electrical systemDriver assistance

Cross traffic and blind spot monitoring/alert failed. Electrical wiring failed due to rubbing on the rear bumper causing failure of blind spot alert and cross traffic alert systems. Reliance on these systems is critical to safe operation of the vehicle.

Filed Incident Electrical system · Lane departure · Back over preventionNHTSA 11676692
Engine & coolingFuel systemDriver assistance

The contact owns a 2021 Ford Bronco. The contact had received notifications of NHTSA Campaign Numbers: 24V635000 (Engine and Engine Cooling), 25V025000 (Suspension), 25V315000 (Back Over Prevention) and 25V455000 (Fuel System, Gasoline); however, the parts to do the recall repairs were not yet available. The local dealer was made aware of the issue and confirmed that parts for all four recalls were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall...

Read the full complaint

repair. The contact stated that the rear camera intermittently displayed a distorted image while the vehicle was in reverse. The manufacturer was made aware of the issue. The failure mileage was unknown. VIN tool confirms parts not available for NHTSA Campaign Numbers: 25V025000, 25V315000, and 25V455000. Parts distribution disconnect for NHTSA Campaign Number: 24V635000.

Filed Incident Engine and engine cooling · Fuel system, gasoline · Back over preventionNHTSA 11673354
Driver assistance

I had the cross-traffic sensor and blind spot detection sensors changed about a year after I bought my Bronco and the tech told me where the wires are housed it is wide open to the elements which cause the wires to fail. This was fixed under warranty and now 2 years later I have the same issue, and Ford will not fix since I am out of warranty. This is not only a design flaw but also a safety issue for someone who relies on those sensors to work.

Filed Incident Lane departure · Back over preventionNHTSA 11669268
Driver assistance

I am receiving Blind spot and cross traffic failure alerts in my vehicle dashboard indicating these systems are not working properly. This is a known issue by many Bronco owners. I believe its due to a bad installation design where the wires naturally rub up against the bumper and with weather exposure they are failing.

Filed Incident Lane departure · Back over preventionNHTSA 11661138
SteeringSuspensionDriver assistance1 injury

Our family was traveling from Lake George New York to Boston MA on Wednesday [[redacted]]. As we passed another vehicle in the far left lane on [[redacted]] the vehicle bounced and we lost control of the backend of the vehicle and it "fish tailed" across the highway nearly causing a collision at 65 miles per hour. The anti-lock breaks were activated and we nearly collided with several cars but managed to pull into the emergency lane. The vehicle was not drivable after this incident because any pothole or bump on...

Read the full complaint

the highway, at speeds over 50 MPH, made the rear of the vehicle very unstable. It will skid and sway. Our vehicle is now undrivable and Ford says the only available solution is a "buy back" program and a solution will not be available until Q3 of 2025. This leaves us with a 4 year old vehicle with only 24k miles undrivable. This is not acceptable. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Filed Incident Steering · Suspension · Forward collision avoidanceNHTSA 11648104
Driver assistance

The contact owns a 2021 Ford Bronco. The contact stated that while in reverse on several occasions, the back-over prevention camera failed to work as intended. The contact stated that on one occasion while in drive, the back-over prevention camera was displayed inadvertently. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 6,000. The VIN was not available.

Filed Incident Back over preventionNHTSA 11639094
Driver assistance

The vehicle will throw a warning saying the cross trafic collision is in operable. A ford tech looked at it and said a wiring harness is chaffed causing blind spot monitioring and cross traffic collision systems to not work. Cost of the part only is $700, not including labor. this is a very serious fault, which could result in injury and fatalitys

Filed Incident Lane departure · Back over prevention · Forward collision avoidanceNHTSA 11632944
Driver assistance

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.

Filed Incident Back over preventionNHTSA 11610145
Driver assistance

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer and two unknown dealers were contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and referred the contact to the NHTSA hotline for assistance. The contact had not experienced a failure. Parts distribution disconnect.

Filed Incident Back over preventionNHTSA 11570118
Driver assistance

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V165000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was contacted it was confirmed that the software to perform the update was not available. The manufacturer was made aware of the issue, and it was confirmed that the parts to perform the software updates were not available. The contact had not experienced a failure. Parts distribution disconnect.

Filed Incident Back over preventionNHTSA 11567524
Driver assistance

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 23V598000 (Back Over Prevention) however the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

Filed Incident Back over preventionNHTSA 11557072
Driver assistance

In late March 2023, the touchscreen on my Bronco went dead, along with the USB ports in the console below. With the dead screen, I have no back up camera, which is a huge safety concern. Also, all other features managed by the touch screen are gone (no radio, no navigation, no hands free phone usage, etc.). I have been to the dealer twice, and they said we just have to wait for Ford engineers to send a patch to the SYNC system, because they think it has interfered with the APIM module. This may or may not be...

Read the full complaint

related to the open recall 22c27, because that is not the same issue as mine. But Ford just is telling me to wait for that recall to be completed, but for four months and counting they have not provided a patch for the 8-inch screen model that I have. I have been given no other options except potential buy back of the vehicle.

Filed Incident Unknown or other · Back over preventionNHTSA 11532834
Driver assistance

The contact owns a 2021 Ford Bronco. The contact received notification of NHTSA Campaign Number: 22V825000 (Back Over Prevention) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure but stated that the VIN was not included in the recall as per the information in their system. The contact had not experienced a failure. Parts distribution disconnect.

Filed Incident Back over preventionNHTSA 11529807

Ford Bronco driver assist complaints by year

Bronco driver assist problems, every year

Had a driver assist problem with your 2021 Bronco? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience