Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2001 Ford Excursion Problems, complaints & recalls

Owners have filed 206 complaints about the 2001 Ford Excursion with NHTSA, most often about the wheels & tires (55) and the engine & cooling (52). Those complaints describe 17 crashes, 19 fires, 14 injuries and 2 deaths. It is covered by 7 recalls, the latest in October 2009 for the vehicle speed control. For comparison, the 2000 has 0 and the 2002 has 172.

NHTSA data checked

FFar more problems than a typical Excursion year, for its age

#47 most complained-about 2001 vehicle

Complaints
206
Recalls
7
Crashes
17
Fires
19
Injuries
14
Deaths
2

Most common 2001 Ford Excursion problems

Share of all 206 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2001 Ford Excursion recalls 7

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Vehicle speed control

09V3990004,500,000 vehicles affected

The problem
Ford is recalling model years 1995-2003 windstar, 2000-2003 excursion diesel, 1993-1997 and 1999-2003 f-250 sd through f-550 sd diesel, 1992-2003 e-150 through e-550, 1995-2002 explorer, 1997 and 2002 mercury mountaineer, 1995-1997 and 2001-2003 ranger, and 1994 f53 vehicles equipped with the texas instruments speed control deactivation switch (scds). The scds may leak internally and then overheat, smoke, or burn.
The risk
A vehicle fire could occur with or without the engine running.
The fix
Ford will notify owners that dealers will install a fused wiring harness in line with the scds. On 1999-2003 windstar vehicles with a leaking scds, dealers will also inspect the abs control module connector and repair as necessary. Repairs will be completed free of charge. The safety recall began on october 27, 2009. Owners may contact ford at 1-888-222-2751.

Wheels: hub

07E106000130,000 vehicles affected

The problem
Certain federal-mogul replacement wheel hub assemblies with the brand names: national, carquest p/nos. 515020, 515021, 515025, 515053, 515054, 515059, And 515060, shipped between january 23, 2006, and december 20, 2007, sold for light duty and medium duty trucks. The inboard retention nut used to maintain hub bearing assembly can loosen resulting in an abs light indication, noise, and/or wheel separation.
The risk
WHEEL SEPARATION CAN RESULT IN A VEHICLE CRASH.
The fix
Federal-mogul will notify customers and will replace the hub assembly free of charge. The recall began on february 7, 2008. Owners can contact federal-mogul toll-free at 877-489-6659.

Engine and engine cooling: diesel

07V5530001,176,000 vehicles affected

The problem
On certain heavy duty trucks equipped with 7.3L diesel engines, the camshaft position sensor located on the engine of the vehicle may function intermittently, possibly resulting in an engine stall.
The risk
In the event of an engine stall, a crash could result without warning.
The fix
Dealers will inspect the sensor and replace it with an improved camshaft position sensor free of charge. The recall began on december 29, 2007. Owners may contact ford at 1-866-436-7332.

Vehicle speed control

06V2860001,200,000 vehicles affected

The problem
On certain trucks equipped with speed control, gasoline or natural gas engines, the speed control deactivation switch may overheat.
The risk
Overheating could result in smoke or burn and an underhood fire.
The fix
Dealers will install a fused wiring harness into the speed control system free of charge. The recall began on august 7, 2006. Owners may contact ford at 1-866-436-7332. (Note: also see recalls 05v017 and 05v388)

Visibility: motor

01V2580001,083,000 vehicles affected

The problem
Vehicle description: passenger cars, sport utility vehicles, and light and medium duty pickup trucks. A switch located in the plastic cover of the wiper motor gear case could malfunction and overheat, potentially resulting in loss of intermittent wiper function, loss of wiper park function, complete loss of wiper function, or ignition of the plastic cover material. Switch malfunction is most likely to occur when the intermittent setting of the wipers is being used, or when snow or ice obstructs the blades from returning to the "parked" position at the bottom of the windshield. These vehicles were built at the following assembly plants: atlanta plant from 2/11/00 through 7/31/00; chicago plant from 2/14/00 through 8/4/00; kansas city plant from 2/26/00 to 9/4/00; kentucky truck plant from 2/18/00 to 8/31/00; michigan truck plant from 2/23/00 through 8/3/00; norfolk plant from 2/21/00 through 7/27/00; wayne stamping and assembly plant from 2/25/00 through 8/15/00; and wixom plant from 2/15/00 through 8/8/00.
The risk
Loss of visibility while driving increases the risk of a crash.
The fix
Dealers will inspect the date code on the wiper motor. Motors built with the suspect time frame will have the wiper motor gear case cover replaced. Owner notification began august 20, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact ford at 1-866-436-7332.

Seat belts: buckle assembly

01V2270011,400,000 vehicles affected

The problem
Vehicle description: passenger and sport utility vehicles, pickup trucks, and minivans. Equipped with seat belts supplied by trw. It is possible that the driver's and/or front passenger's outboard seat belt buckle may not fully latch. Ford crown victoria built at st. Thomas assembly plant from 4/17/00 - 5/29/01 Mercury grand marquis built at st. Thomas assembly plant from 4/17/00 - 5/29/01. Lincoln town cars built at wixom assembly plant from 3/27/00 - 5/30/01. Lincoln navigators built at michigan truck plant from 4/11/00 - 5/31/01. Ford windstars built at oakville assembly plant from 3/23/00 - 5/30/01. Ford rangers built at twin cities plant from 3/28/00 - 5/30/01, and also at the edison plant from 3/13/00 - 5/25/01. Ford f-150 truck built at norfolk plant from 4/18/00 - 5/25/00; at ontario plant from 5/10/00 - 5/28/01; at kansas city plant from 9/11/99 - 5/25/01; and at cuautitlan plant from 5/16/00 - 6/9/01. Ford super duty f-250, f-350, f-450, and f-550 trucks built at kentucky plant from 4/17/00 - 5/27/01; and at cuautitlan plant from 5/16/00 - 6/19/01. Ford excursions built at kentucky plant from 4/17/00 - 10/2/00. Ford expeditions built at michigan truck plant from 4/11/00 - 5/31/01.
The risk
In the event of a crash, the restraint system may not provide adequate occupant protection, increasing the risk of personal injury to the seat occupant.
The fix
Dealers will inspect the front outboard seat belt buckles and if the buckle fails the inspection process, it will be replaced. Owner notification began july 25, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact ford at 1-866-436-7332.

Air bags: frontal

01V082000268 vehicles affected

The problem
Vehicle description: passenger and sport utility vehicles. The inflator canister in the driver air bag module may have an inadequate weld near the igniter.
The risk
In the event of a vehicle crash, the driver air bag may not deploy as intended, potentially resulting in reduced occupant protection, or a burn injury.
The fix
Dealers will install a driver air bag module. Owner notification began march 19, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact ford at 1-800-392-3673.

What owners say

Be the first Excursion owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

206 complaints about the 2001 Ford Excursion

Newest first, as filed with NHTSA by owners. Page 9 of 9.

Suspension

When driving at highway speeds and road is just a bit uneven, vehicle bounces all over road. Hard to control, this does not happen when towing trailer. *Ak consumer states that the front bottoms out and causes the front end to rise suddenly, consumer feels the problem is with the rubber stoppers that are bolted to the frame that keep the spring from hitting the frame, the ones on this vehicle are only 3/4 inch clearanced from the top of the spring to the stopper, consumer states most vehicles have 4 inches. *Slc

Filed Incident SuspensionNHTSA 885778
Suspension

Vehicle experiences excessive vibration while in motion. Dealer rebalanced tires. At a second visit, dealer replaced all four tires. But problem still occurs. *Ak

Filed Incident SuspensionNHTSA 885737
Suspension

Consumer was traveling about 60mph on highway without prior notice front end of vehicle started bouncing up and down to the point that driver almost lost control of vehicle. Dealership aware of problem.*Ak

Filed Incident SuspensionNHTSA 885482
Wheels & tires

Load bang and tire blew out in interstate 80. Look like internal rip by tread ware tire was destroyed. Dealer replace but offered no reason as to what happened. *Ak (tiresize: 265/75/16)( dot number: tire size: 265/75/16 )

Filed Incident TiresNHTSA 743374
Acceleration & cruise control

Failure of cruise control to cancel from the steering wheel or from the brake. The cruise control was activated at approximately 65-70 mph. After applying the foot brake the vehicle failed to disengage the cruise control. I was fortunate enough to be able to reduce the speed even as the rpm continued to stay at 2000rpm, although it took a much greater distance than normal. I brought the vehicle to a stop and the engine continued to rev at 2000rpm. The cancel button on the steering wheel would not disengage the...

Read the full complaint

engine rpm at 2000, and neither would the brake pedal. I pulled to the right side of the road and and placed the transmission in park, and the engine continued to rev at 2000rpm. I applied more fuel and was able to rev the engine between 2000 and 3000rpm only. The cancel button on the steering wheel continued to be inoperable. Finally, at one point, I released my foot from the brake pedal and the rpm then dropped to the normal idle range. I then opened the hood and inspected the engine compartment but was unable to see anything significant to have caused this to have occurred. I consider myself quite lucky to have been in the particular driving situation where I had ample room to bring the vehicle to a stop without having been involved in an accident or to have involved others in an accident. My suspicions are that the code that monitors the switches was somehow confused. I have taken the vehicle to covert ford where it has been since 11/14/2000. Yesterday, I am told, a fmc technical rep has looked over the vehicle. To date no one else , I am told, has been able to replicate the problem. This is the second time reporting this problem. The initial report was identified by nhtsa as "odi-735-005" but the report does not appear on your databases. *Ak

Filed Incident Vehicle speed controlNHTSA 737481
Acceleration & cruise control

The cruise control was activated at aproximately 65-70mph. After applying the foot brake the vehicle failed to disengage the cruise control. I was fortunate enough to be able to reduce the speed even as the rpm continued to stay at 2000 rpm, although it took a much greater distance than normal. I brought the vehicle to a stop and the engine continued to rev at 2000 rpm. The cancel button on the steering wheel would not disengage and neither would the brake. I pulled to the side of the road and placed the...

Read the full complaint

transmission in park, and the engine continued to rev at 2000 rpm. I applied more fuel and was able to rev the engine between 2000 and 3000 rpm only. The cancel button on the steering wheel continued to be inoperable. Finally at one point I released my foot from the brake pedal and the rpm then dropped to the normal idle range. I then opened the hood and inspected the engine compartment but was unable to see anything significant to have caused this to have occurred. I consider myself quite lucky to have been in the particular driving situation where I had ample room to bring the vehicle to a stop without having been involved in an accident or to have involved others in an accident. Having worked with computers for most of my life I suspect that the code was somehow fouled up that may or may not be involved in monitoring the status of the cancel switches...Just a hunch. Have there been any other reports of such an incident on ford excursion or ford f250 from which this model is derived?

Filed Incident Vehicle speed controlNHTSA 735005

Ford Excursion: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
20050200-B
200495243Engine & coolingF
20031465711Electrical systemF
200217251513Engine & coolingF
200120671719Wheels & tiresF
20000600-D
19990100-A
19980100-A
19970100-A
All Excursion years

2001 Ford Excursion vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2001 Ford Excursion? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2001 Ford Excursion

Does the 2001 Ford Excursion have any recalls?

Yes - NHTSA lists 7 recalls for the 2001 Ford Excursion: vehicle speed control (October 2009); hub (December 2007); diesel (December 2007); vehicle speed control (August 2006) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2001 Ford Excursion?

By the complaints owners filed with NHTSA, the most common problem areas are the wheels & tires (55), engine & cooling (52), transmission & drivetrain (20).

How many complaints has the 2001 Ford Excursion had?

206 complaints have been filed with NHTSA, the first on October 24, 2000 and the latest on April 25, 2023. Of these, 17 describe a crash and 19 a fire, and together they report 14 injuries and 2 deaths.

Is the 2001 Ford Excursion a reliable vehicle?

Its Safety Index is 1 out of 100 (grade F: far more problems than a typical Ford Excursion year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Ford Excursion years have the most complaints?
What should I do if my 2001 Ford Excursion has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience