- The problem
- Daimler trucks is recalling certain model year 2005-2011 freightliner cascadia, columbia, century, coronado, and classic xl trucks manufactured from november 1, 2004, through june 15, 2010 for the rack and pinion steering system. The lower pinion bearing may corrode and fail. A failed bearing may lead to damage of the spool valve seals. A damage spool valve seal may allow hydraulic fluid to flow to the right or left turn port instead of flowing to the return port.
- The risk
- The steering could unexpectedly turn left or right, making the vehicle more difficult to control and increasing the risk of a crash.
- The fix
- Daimler trucks will inspect the lower bearing for corrosion. If corrosion is found, the rack and pinion system will be replaced. If no corrosion is found, on the bearing, the bearing will be packed with grease and the rubber bellows will be replaced with sealant added between the bellows and the rack housing. An interim letter was mailed in december 2011. Owners may contact daimler trucks toll-free at 1-800-547-0712.
Steering
2010 Freightliner Cascadia Steering problems
Owners have filed 4 complaints about the 2010 Freightliner Cascadia's steering with NHTSA - 33% of all its complaints, most recently on April 12, 2018. They describe 1 crash, 0 fires and 0 injuries. Loss of power steering, stiff or loose steering, wandering, column and rack problems.
- Complaints
- 4
- Recalls
- 3
- Crashes
- 1
- Fires
- 0
- Injuries
- 0
- Deaths
- 1
Steering recalls for the 2010 Freightliner Cascadia
- The problem
- Daimler trucks is recalling certain model year 2010 freightliner cascadia vehicles manufactured may 20, 2009 through january 29, 2010 and equipped with optional sheppard hd94 steering gears. Restraining washer locking tabs may not have been seated into the pitman arm retainer notches during assembly.
- The risk
- Incomplete installation of the pitman arm retaining mechanism may allow unthreading of the retainer. Disengagement of the pitman arm from the steering box may result in loss of steering and crash could occur.
- The fix
- Dealers will inspect to insure pitman arm retainer is properly torqued and restraining washer is properly installed with locking tabs seated in notches of the retainer. This service will be performed free of charge. The safety recall is expected to begin on or before april 2, 2010. Owners may contact daimler trucks at 1-800-547-0712.
- The problem
- Daimler trucks is recalling certain model year 2005 through 2010 heavy duty trucks manufactured from october 29, 2005 through july 3, 2009. Under certain condition, the left hand inner tie rod end may loosen over time and if not corrected, potentially separate from the steering rack.
- The risk
- A separated tie rod assembly can result in loss of vehicle control at higher speeds and a crash could occur.
- The fix
- Daimler trucks will notify owners and the vehicles will be repaired free of charge. The safety recall began on february 5, 2010. Owners may contact daimler trucks toll-free at 1-800-547-0712.
Steering complaints
Tl* the contact owns a 2010 freightliner cascadia. Upon starting the vehicle, the steering wheel was unable to be turned to the left or right and there was power steering fluid on the pavement. The vehicle was towed to an independent mechanic where it was diagnosed that the rack and pinion failed and needed replacement. The vehicle was not repaired. The contact also stated that the vehicle had been previously repaired four times for the same failure by the same independent mechanic. A freightliner dealer was not contacted for diagnostic testing or repairs. The manufacturer was notified of the failures. The approximate failure mileage was 1,000,000.
Dpf system frecuenty regeneration ( every day and take 2 hours to clear)and oil pump problems when stop at red lights also bad steer ploblems bad king pints
Tl* the contact owns a 2010 freightliner cl125. The contact stated that the driver was driving approximately 45 mph, when the truck suddenly rolled over without any warning. The driver passed away due to the crash. The police were notified and a report was available. The truck was not taken to have the failure diagnosed or repaired. The contact examined the truck and stated that the rack and pinion was fractured. The contact was not sure if the fractured rack and pinion was the cause of the failure. The manufacturer was notified and they advised the contact not to touch the vehicle until an investigator was sent. The failure mileage was approxmately 180,000. ...Update 01/20/12 *bf
Tl* the contact owns a 2010 freightliner cascadia. The vehicle was taken to an independent mechanic who detected that the rack and pinion steering was faulty. The vehicle was repaired. The manufacturer was not notified of the problem. The failure mileage was 170,333. Updated 11/16/11*lj the consumer referenced recall # 09v357000. Updated 02/27/12
Freightliner Cascadia steering complaints by year
Cascadia steering problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data