Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Acceleration & cruise control

Freightliner Cascadia Acceleration problems by year

19 complaints filed with NHTSA about the Freightliner Cascadia's acceleration & cruise control. Unintended acceleration, surging, throttle problems and cruise or adaptive cruise faults.

Acceleration complaints by model year

YearAcceleration complaintsCrashesInjuriesRecalls
20246000
20231000
20202000
20193000
20181000
20171000
20151000
20141000
20131000
20111000
20091000

Latest Cascadia acceleration complaints

2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise...

Read the full complaint

control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633142
2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the...

Read the full complaint

self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633141
2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well...

Read the full complaint

over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633138
2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only...

Read the full complaint

part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633136
2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will...

Read the full complaint

accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633132
2024 Freightliner CascadiaAcceleration & cruise controlDriver assistance

The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic...

Read the full complaint

situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.

Filed Incident Vehicle speed control · Forward collision avoidanceNHTSA 11633126
2023 Freightliner CascadiaElectrical systemAcceleration & cruise controlDriver assistance

Dash light warning lights come on and causes the cruise control to stop working. A total of 6 fault lights comes on and also causes the Adaptive Cruise Control to not work. This is the 3rd Freightliner Cascadia that I have driven in the past 3 and a half years and every single truck has had the same problem. Freightliner has refused to acknowledge that there is a problem. Nobody seems to know what to do to correct the problem. We are owner operators and long haul drivers and needcruise control. Freightliner dealers are almost impossible to get anything repaired because they do not accept appointments and they have so many trucks sitting around waiting for repairs.

Filed Incident Electrical system · Vehicle speed control · Forward collision avoidanceNHTSA 11535215
2020 Freightliner CascadiaSteeringAcceleration & cruise controlDriver assistance

Multiple safety issues with truck #1 When driving & using cruise control (CC) at 60 mph & truck is at that speed (60 mph) truck is moving from top speed to E coast mode. Immediately RPM is down (from 1250 to 600) & steering wheel is much harder b/c reduced power from engine . Response time for driver to avoid potential hazardous situations on the road (i.e. animals, rocks, trees, etc.) is longer & not safe #2 This problem is related to when truck is in regen. In driving, and when truck is doing regen (visible on...

Read the full complaint

the dash: high temp light/ icon). CC set to (60 mph) when truck is at that speed (60 mph) truck goes to E coast mode. RPM is going down to 600 RPM which is not adequate engine speed to finish regen. With regen interrupted there is a lot of white smoke under the truck and red light for engine shut down is on the dash. There is 30 seconds time to override shut down but at the same time the driver needs to safely park the truck on the shoulder, on a busy highway, with reduced power and steering wheel (600 RPM or no power at all because engine shut down). With high DPF temperature,there is potential for fire (truck,grass,trees ). I am told engine shut down was caused by interrupted regen process. #3 Collision warning is coming with no reason, and can activate active brake, at high speed. Radar malfunction (snow, ice in the front)can cause malfunction to adaptive cruise control, active brake assist, & malfunction other safety features. Combination of malfunction (radar, active break assist, collision warning, IPM [intelligent powertrain management], engine break not engaging) can cause dangerous acceleration for heavy loaded truck. I contacted DTNA (Daimler Truck North America) in regard to these issues & am told in order to solve these issues the truck should be inspected where mechanics and programmers are involved. At the same time I spoke with the company I work for about safety issues with those trucks. You can contact me for further information.

Filed Incident Steering · Vehicle speed control · Forward collision avoidanceNHTSA 11505866
2018 Freightliner CascadiaElectrical systemAcceleration & cruise controlDriver assistance

Had same issues on 2018-2020 freightliner cascadias (7 different units), chassis harness rubbing against transmission and the metal bracket by the air compressor. Active fault codes for coolant level , tcs, transmission ecu - drivers not able to drive on automatic mode/ only manual mode available. One time the driver was not even able to start the truck in the morning, had to get the unit towed to the dealer and have the harness repaired. All of the faults previously described could happen in motion and/or when vehicle was stationary.

Filed Incident Electrical system · Vehicle speed control · Electronic stability control (ESC)NHTSA 11366557
2019 Freightliner CascadiaAcceleration & cruise controlBrakes

Truck slams on its brakes randomly. Locks them up when there is nothing in front of me and has almost caused me to have a bad accident. It has been doing this ever since I started driving this truck and have put 25,000 miles on it. It has 50,000 miles on odometer. I have been driving for 35 years with no accidents and this truck is going to cause a very bad accident. I am a penske driver based in mt hope ohio and management is doing nothing. We have 10 of these trucks at our facility with this braking feature and...

Read the full complaint

we are all about to quit or hire attorneys. Thanks [[redacted]]. [[redacted]] information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr

Filed Incident Vehicle speed control · Service brakesNHTSA 11271439
2020 Freightliner CascadiaAcceleration & cruise controlElectrical system

Tl* the contact owns a 2020 freightliner cascadia. While driving with the cruise control engaged, the vehicle unintentionally accelerated. Also, the crash warning icon illuminated although there was no object in front of the vehicle. The vehicle was taken to penske truck rental (1405 glendale ave, sparks, nv 89431, (775) 359-6226) to be diagnosed, but the cause of the failures could not be determined. The vehicle was not repaired. The manufacturer was not made aware of the failures. The failure mileage was 4,766. Contact also alleged loss of power steering assist when turning left at a lower speed that required additional steering effort.

Filed Incident Vehicle speed control · CommunicationNHTSA 11193866
2019 Freightliner CascadiaAcceleration & cruise controlBrakes

Our company says the 2019 will not idle when it is between 30 and 60 degrees , well problem it can be 58 outside and its over 70 inside, well roll down the windows , yeah now no safety for the driver, and we have woman out there to. So I dont thing they want to be raped, so idling the truck should be up to the driver not the company. With out proper sleep you now have sleep drivers driving 80,000 pound weapons on the freeways, first person killed will be on your heads if this isnt taken care of. Crash pervention...

Read the full complaint

system all ok but when driving on slick roads and someone jumps in front of you the truck slams on the brakes and we dont have control anymore, oh yeah this is safe not. This needs to be addressed quickly before someone dies.

Filed Incident Vehicle speed control · Service brakesNHTSA 11091048
2011 Freightliner CascadiaFuel systemAcceleration & cruise control

Tl* the contact drove a 2011 freightliner cascadia. The contact drove the vehicle for work. The contact stated that the diesel enhancement fluid level component failed to work properly, including the sensor/warning indicator. In addition, the speedometer failed to function and the equipment was not functioning properly. The contact was not able to drive the vehicle due to the failures. The vehicle was left at a truck stop. The manufacturer was notified of the failures. The vin and failure mileage were not available.

Filed Incident Fuel system, diesel · Vehicle speed controlNHTSA 10950072
2017 Freightliner CascadiaAcceleration & cruise control

This complaint pertains to adaptive cruise control (acc), forward crash avoidance (fca) and lane departure warning systems (ldws). I have been driving this specific vehicle but it will pertain to all vehicles with these systems. The acc and fcas because of its straight line of sight is misinterpreting the data on approach to bridges, overpasses and overhead signs and will initiate a hard braking event on the interstate when no braking is required causing the potential to lose control and for a following vehicle to...

Read the full complaint

crash. This problem would be intensified on wet, icy and snow covered roads. I have also experienced a hard braking event on interstates on approach to a curve in the road where vehicles ahead will already be in the curve in another lane and the data is misinterpreted as a crash and brakes hard because the other vehicles are directly in the line of sight. Again, no braking was required. On approach to a vehicle on the highway ready to move into another lane to execute a passing maneuver the vehicle is braked forcing a loss in vehicle momentum when no braking was required. In inclement weather, rain, snow, frost and fog the sensors become unable to see which is the best thing that could happen and the only way to disable it that I know of. These events occur every single day on my trips. I am a professional driver with 35 years' experience in commercial vehicles and 40 in a car. I drive 570 miles a night. These technologies in their current state have no place in vehicles on the public highway systems. With winter coming I am very concerned for my safety and that of the motoring public and want a record of my complaint on file. Truck is equipped with the detroit assurance 2.0 System.

Filed Incident Vehicle speed controlNHTSA 10926597

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience