Daimler Trucks North America, LLC (DTNA) is recalling certain 2024-2025 Western Star 49X and 2025 Freightliner Cascadia vehicles. The Electronic Stability Control (ESC) software has incorrect axle spacing parameters. As such, these vehicles fail to comply...
Driver assistance
Freightliner Cascadia Driver Assist problems by year
55 complaints filed with NHTSA about the Freightliner Cascadia's driver assistance. Phantom braking, automatic emergency braking, lane keeping, blind spot and collision warnings.
Driver Assist complaints by model year
Driver Assist recalls
Daimler Trucks North America, LLC (DTNA) is recalling certain short wheelbase 2020-2024 Freightliner Cascadia, 2021-2024 Freightliner M2 Business Class, 2022 Western Star 4700, and 2020 Freightliner Classic Cascadia vehicles. The vehicle is equipped with an...
Daimler Trucks North America, LLC (DTNA) is recalling certain 2017-2023 Freightliner Cascadia, 2020-2023 Western Star 49X, 2021-2023 Western Star 47X, and 2022 Freightliner 114SD vehicles. The brake modulator valves on the front axle may corrode and cause...
Daimler trucks is recalling certain model year 2006-2012 freightliner business class m2, cascadia, century, columbia, coronado and sterling a-line vehicles built with meritor wabco electronic stability control (esc) system manufactured from september 15, 2005...
Latest Cascadia driver assist complaints
My main concern is whether the brake modulator valve recall is related to recurring brake problems on our 2019 Freightliner Cascadia. I am asking NHTSA to investigate whether the recalled valve contributed to the defects found during a roadside inspection and whether the recall repair addresses the risk of these problems happening again. On November 2, 2026, an Illinois roadside inspector placed the truck out of service after finding a leaking brake chamber, a brake out of adjustment, and an inoperative automatic...
Read the full complaint
slack adjuster. Before departure, the driver performed a pre-trip inspection with the engine running. The driver reported hearing no air leak and noticing no loss of air pressure or difficulty braking. It is unknown whether a dashboard warning appeared. The repair shop confirmed that the brake chamber was leaking air. All three cited defects were corrected. Similar brake problems have occurred on this truck before. My concern is that they could recur while the truck is in service and affect its ability to stop safely before the driver notices a problem. The connection to the recalled valve remains unconfirmed.
Without warning an Automatic breaking event occurred and the tractor slammed on its breaks while on open road with no one near on a sunny day. I was bobtailing south.. That event caused my AEB system to disable itself and I also lost cruise control. The funny thing is even after the system is disabled I'm still having automatic breaking events around curves..
The front sensor is calibrated wrong. It slams my brakes on road if a shadow is in road, bridges, vehicles parked on side of road, and sometimes if another semi passes me it slams the breaks on. It happens if its just raining out not so much winter because snow and ice blocks the sensor. This has also almost caused accidents as well.
The forward collision avoidance system fails to distinguish stationary objects from animate objects resulting in immediate engagement of the braking system.
I was north of Louisville Kentucky on [[redacted]] traveling at 65 mph and I was in the middle lane and the collision lights came on and the truck abruptly started stopping. Luckily no one was on my right side. I made it to the shoulder of the road. Thank God I wasn't rear ended by anyone and there were three lanes of traffic. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The cruise control has been programmed to stay engaged, in many instances, after the driver has used the foot brake. In some situations, like approaching a traffic circle, I have slowed down with the foot brake, then had the truck unexpectedly start to accelerate after I released the brake. This apparently has to do with a vehicle in my headway allowing the cruise to remain engaged, and then after the vehicle leaves my headway the truck thinks it can accelerate again. There is never a good reason for the cruise...
Read the full complaint
control in any vehicle to remain engaged after using the brakes. This results in unpredicted situations, like unplanned acceleration. This also applies to vehicles trying to merge in front of me, where I use the brakes to back off some and allow them in, but then the cruise (still engaged) will accelerate again toward the vehicle that was previously in my headway.
Complaint 1 When using cruise control in 2024 Freightliner Cascadia trucks with level 2 autonomous driving features, there is no option to turn off the autonomous driving features (and use standard cruise control); the driver is forced to use the system if he wants or needs to use cruise control. This apparently is a software setting that is available in some versions, but is not available in models bought/leased to large trucking companies. Complaint 2 There is no way to adjust the "agressiveness" of the...
Read the full complaint
self-driving (acceleration and braking) feature of these trucks. The default in this model truck is unknown to me, but in slow-and-go or stop-and-go traffic, the truck is highly aggressive; the truck follows too close very often, and waits until the last second to slow or stop in most cases. This also happens in high volume, higher speed traffic.
These trucks have a non-adjustable default setting for Over and Under cruise control speed setting. This means, in the case of the truck I drove, that the cruise control will allow the truck to go 5 mph over the set speed before engaging the engine brake, or 4 mph under the setting before accelerating. The problem is that when set for the speed limit, the truck will climb to 7 mph over the set speed before engaging engine brake. When driving on a downgrade with a lot of weight, the truck quickly gets to well...
Read the full complaint
over a safe speed before the truck will attempt to slow down. This often results in an overspeed situation when approaching curves. In older models of Freightliner, and maybe in current versions that are adjustable, there is a setting to change this to closer to the set speed. In this model, or large companies' ordered versions, this adjustment is not available. The idea is to save fuel by "hyper-mile" style of driving. It makes for an unpredictable speed of vehicle, frustrating other drivers, and sometimes leading to unsafe overspeed situations.
When a vehicle is merging into my lane, the truck will often not detect or react to the encroaching vehicle; this happens even when there is plenty of space, and the encroaching vehicle is halfway into my lane. I have had to intervene several times, since the truck was accelerating toward the previous vehicle in my headway, and ingoring the intervening merging vehicle. In contrast, the sensors in the truck apparently can see when a vehicle is near to the front, and mostly out of the headway of the truck (only...
Read the full complaint
part of the front vehicle in my lane, like when exiting). This truck will brake, and continue braking unnecessarily (and unnecessarily hard braking) for a vehicle that is completely out of my lane (by several feet), before continuing and regaining speed. This shows that the sensors are capable of "seeing" and tracking the vechicles, but still does not respond to traffic merging into the truck's headway.
When driving in highway traffic at moderate to high speeds (as well as low speeds), the truck will often accelerate with (and towards) a vehicle that is less than 1 second ahead of the truck. Certainly this often happens when there is not a safe distance between the truck and the next vehicle. The trucks systems in no way seem to expect that the next vehicle could slam on brakes at any moment. I have had this happen many times when a vehicle merges too close in front of me and then accelerates. The truck will...
Read the full complaint
accelerate with the vehicle (that the truck is now tailgating), even though there is slowing or stopping traffic directly ahead of the vehicle the truck is following. The Safety Director at Tyson Foods, Robert Carl, told me in a conference call about the unsafe flaws in the truck, that these Freightliner systems are programmed to "try" to maintain about a 2.5 second following distance. Even this is patently unsafe. Driver safety guidelines (FMCSA) are: "If you are driving below 40 mph, you should leave at least one second for every 10 feet of vehicle length. For a typical tractor-trailer, this results in 4 seconds between you and the leading vehicle. For speeds over 40 mph, you should leave one additional second." It would appear that Daimler/Freightliner may have used Autonomous Driving software that was designed for cars, and has tried to "adjust" it to work in tractor-trailers. That is speculation, but based on the supposed target following distance, that may be correct. 2.5 seconds is certainly too close, and the distances of less than 1 second that I have commonly seen are not acceptable in any truck.
When approaching stopped traffic, sometimes the truck will respond and begin to slow down. At other times, the truck will continue at set speed toward a detected stopped vehicle, and in situations where the time and distance are way too short to justify no reaction by the system. The truck at sometimes acts like it is auto-driving; at others it acts as if it is only in crash-mitigation mode, and will wait for the driver until the last possible second and then slam on brakes. There have been some times where the...
Read the full complaint
truck actually gave a collision warning (alarm and display turns red), but in no way attempted to slow itself. This happens with vehicles detected in the truck's headway for multiple seconds beforehand. In short, the truck will sometimes apparently allow itself to rear-end a vehicle in front of itself, even though the sensors detected it and it had plenty of time to react. When there has been a collision warning with no action by the autonomous system, it has often been when there is less than 1/2 second for the driver to intervene.
The cruise control (level 2 autonomous) will turn itself off without any warning sometimes. This happens any time the truck is set for above the speed limit by more than 2 mph. The truck uses a speed limit map, independent of actual posted speed limits. When the truck detects a speed limit drop to below the cruise setting, either real or imagined, the cruise control disengages without any warning or notification. This is a problem when I expect the truck to continue its autonomous function in traffic...
Read the full complaint
situations, but it does not, and without warning. The system will even disengage while it is operating; it will be slowing or maintaining a following distance, then disengage. The driver has no idea if the truck is still auto-driving until he is close to a rear-end accident. Also, bear in mind that speed limit signs are often only posted on the right side of the road; If there is something blocking the sign, like another vehicle, the cruise will still disengage without warning, and the driver does not know it. The only way to tell if cruise is still engaged is by looking for a small green icon in the bottom left of the dash display, which is over 20 degrees down from focal view. Also, there are times when the cruise disengages for no apparent reason. Sometimes there is a barely audible bluetooth-disconnect type sound, but often there is no audible warning. There is also no display warning of any type.
ABS system is shutting causing all safety systems to shut down including cruise control. Freightliner is overlaying the harness for abs sensors at the owners expense. There should be a recall for them to fix this issue. They are very aware of what's going on and are doing nothing to fix the issue.
While driving on the highway on cruise at 70mph the right front brakes locked up. The day was clear. I was driving across a bridge. The truck pulled to the right and I fought to pull it back on to the road. My company has the incident on camera. I was pulling a loaded tanker. Had the pavement been wet or snowy I could have easily jack knifed. If a vehicle would have been next to me I would have struck them. The vehicle was inspected by our mechanic and was told the system was within specs. The truck has also hard braked and pulled to the right when vehicles in the lane next to it are turning.
While approaching an overpass the collision mitigation system activated my brakes nearly causing the vehicle behind me to rear end my trailer, hit my brakes so hard i was thrown forward.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data