Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Brakes

Grand Design Reflection Brake problems by year

52 complaints filed with NHTSA about the Grand Design Reflection's brakes. Spongy or hard pedal, ABS faults, brake failure, noises, parking brake and brake fluid leaks.

Brake complaints by model year

YearBrake complaintsCrashesInjuriesRecalls
20251000
20241000
20213000
20191000
20183000
201718000
201614000
201510000
20141000

Latest Reflection brake complaints

2025 Grand Design ReflectionElectrical systemBrakes

The electric brakes on my new 2025 Grand Design Reflection 260RD fifth-wheel lock up without warning while towing, on both tows since purchase ([redacted] leaving the dealer in [[redacted]];[redacted] near [[redacted]]). On [redacted] the brakes locked about 12 times at a stop sign intersection and about 4 more times entering a four-lane highway with cars waiting behind; I had to unplug the trailer connector in traffic, leaving no brakes or lights. Not the tow vehicle (F-250 scanned, no codes; same lockup with a...

Read the full complaint

second truck). Blue Compass W/O [redacted] shows a short-to-battery fault on each wheel (Lippert case [redacted]). Each fix was only a controller reset; the cause has not been found or repaired and the fault returned. Locked brakes could stop the vehicle in the path of traffic or cause loss of control at speed, with risk of injury or death. No injuries or collision so far. Trailer is available for inspection; full records available. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Filed Incident Electrical system · Service brakesNHTSA 11774015
2024 Grand Design ReflectionBrakes

Trailer is equipped with the Lippert ABS brake system. During final review of issues covered by warranty at the Dealer (General RV in Birch Run MI) the dealer recommended a wheel bearing re grease which I agreed to. During this procedure the left rear brakes were noted as totally worn out and the brake drum had a significant crack due to excessive heat from the dragging brake. This trailer has approx. 8000 mi of towing. As of now root cause has not been determined but if I had not opted for the wheel bearing...

Read the full complaint

grease service the problem would not have been discovered. Failure of the cracked drum could have caused wheel lockup and led to a loss of control. There was no indication of a problem when driving

Filed Incident Service brakesNHTSA 11649902
2018 Grand Design ReflectionBrakes

A thin rubber grommet is used to protect the electric brake wires passing through the axel tube. These grommets wear through during normal towing. This, in turn, causes the wire to short to ground leading to total failure of the trailer brakes. I did not experience an accident but came very close as I was approaching a stopped vehicle and realized I needed MUCH more braking force on my truck brakes to stop my forward movement. All 4 grommets on the 2 axels on my trailer have failed as shown in the attached...

Read the full complaint

pictures but only one has resulted in the wire being rubbed through causing the brake failure. A picture of the axel ID is also included. This appears to be a serious design flaw that should be corrected. A quick Internet or YouTube search will show there are many occurences of this!

Filed Incident Service brakesNHTSA 11613694
2021 Grand Design ReflectionBrakes

one brake shoe pad came completely off the mount plate, so no effective braking on that wheel

Filed Incident Service brakesNHTSA 11481658
2021 Grand Design ReflectionBrakes

We have taken two trips with trailer and (Tow vehicle - 2021 Ram 2500). First trip in April 2021 of about 150 miles round trip no problems were encountered. Second trip in May 2021 with a round trip of 380 miles we had repeated instances of "Check Trailer Brake Wiring" and "trailer disconnected" appear on dash. These warnings would disappear after a few moments. When safe to do so after first instance (and the warning was off) I pulled off the road and checked connection and trailer brakes by engaging the...

Read the full complaint

emergency trailer brake switch and trying to pull away. It appeared that the trailer brakes held. This cycle continued for trip to and from RV park. This month, I made an appointment at the RV Dealer, hooked up the trailer, checked operation of turn signals and brake lights and checked that the trailer brakes would engage. They did. When pulling out of storage lot, the warnings appeared, I tried to engage the trailer brake emergency brake while the warning was still on the dash and found No trailer brakes. I proceeded to drive to the RV dealer and the warning disappeared and brakes seemed to function. While I believe the truck brakes will stop the trailer at slow speeds, I am worried about the situation at highway speeds. Trailer is at the dealer waiting in a repair queue. I had telephoned the Grand Design RV customer service line and was told they weren't aware of a problem. However, a friend with the same year and model trailer but a different tow vehicle has encountered the same brake warning issue.

Filed Incident Service brakesNHTSA 11419813
2021 Grand Design ReflectionBrakes

The electric brakes on our brand new 2021 Grand Design Reflection 303RLS periodically go out. We get a warning through the brake controller that the trailer is disconnected or to "check trailer brake wiring." The warning will go away and the electric brakes will work again, only to have the problem return with the complete loss of trailer brakes. This problem occurred on our very first outing with the new 5th wheel trailer. We have contacted Grand Design customer service through telephone and email, but have...

Read the full complaint

received no response. We have scheduled a service appointment to have this issue investigated, but the service department at General RV in Huntley, IL has pushed out our appointment several weeks as they are quite busy. Having no brakes on a 5th wheel trailer that weighs close to 12,000 lbs. loaded is obviously quite concerning to us.

Filed Incident Service brakesNHTSA 11419770
2017 Grand Design ReflectionBrakes

Intermittent brakes (lost brakes) on fifth wheel due to the use of undersize wire and overuse of scotchlok guillotine connectors. Each brake has a maximum current draw of 4amps. 4X4 = 16 amp possible draw on 14 awg wire at approximately 60+ foot loop round trip from pin box to brakes back to pin box. This is an extremely dangerous situation. The brake wiring is substandard in every conceivable way. Should be at least connected 10awg using crimped butt splices and circle connectors. It would also help to have...

Read the full complaint

a ground bond at the axle to reduce the loop by 50%. Someday someone will die (probably have already) because of cheap undersized wire with cheap guillotine connectors everywhere. For lights ok for brakes? Never!*Dt*jb

Filed Incident Service brakesNHTSA 11396988
2019 Grand Design ReflectionBrakesFire

Tl* the contact owns a 2019 grand design reflection trailer equipped with self adjusting brakes. The contact stated that while driving approximately 35 mph smoke was present coming from the front driver side axle. Upon inspection it was discovered that the brakes were very hot and smoking. The trailer was taken to the local dealer bretz rv & marine (2999 old hardin rd billing, mt 59101) the cause of the failure was not determined. The manufacturer was not yet notified. The failure mileage was 1,500. *Bf consumer stated axle company paid to fix trailer.*Jb

Filed Incident Service brakesNHTSA 11327697
2017 Grand Design ReflectionBrakes

Two separate issues: 1. Lippert wheel bearings leaked grease all over the drum brakes with less than 4000 miles. Lippert refused to pay for repairs because it has been more than one year. 2. With brand new brakes properly adjusted, brakes are still very weak. Applying 12 volts from brake controller results in minimal braking. Suspect undersized final wiring to brakes (20 gauge). Brakes have been underperforming since day 1. *Dt*jb*dt*jb

Filed Incident Service brakesNHTSA 11228422
2016 Grand Design ReflectionWheels & tiresBrakes

I've had 2 wheel bearing failures on the same wheel. I'm wondering if the unit is over weight for these bearings. Gvwr 9995 lb, 2 axles rated 4400 lb each, 1536 lb hitch weight. Unit gvwr of 9995 lb minus hitch weight of 1536 lb puts 8459 lb on the axles. Two 4400 lb axles means 8800 lb total axle strength minus 8459 lb trailer weight means axles should be sufficient. Except that it runs on rvd-h 65535 hubs. I've been told that "65535" translates to: 6 bolt, 5.5 Inches between bolts and the 35 means 3500...

Read the full complaint

lb bearings. If the strength of an axle is limited by its weakest component then it seems that the weight limit of the axle should be 3500 lb instead of 4400 lb, and if the weight limit of the axles is actually 3500 lb instead of 4400 lb then the axles would be overloaded by 1459 lb, i.E. 8459 Lb minus 7000 lb = 1459 lb when the wheel bearing failed the first time it was replaced with a 3500 lb. Bearing. At that time I did not understand the potential problem. I am not an engineer. Maybe the components are adequate for the job. I know that components are usually rated well below what they can tolerate but, on the other hand, if the manufacturer is using sub par components to save a little money then maybe they should be "encouraged" to save the money on less strategic components. These breakdowns have already cost me over $1500. Vehicle was in motion at mile marker 400 on i-25 in northern new mexico. Traveling straight, warning message came on dash stating that the trailer brakes malfunctioned. *Dt consumer stated he is not the original owner.*Jb

Filed Incident Wheels · Service brakesNHTSA 11190479
2016 Grand Design ReflectionBrakes

Suspected diminished braking action while towing my 2016 grand design 313 rlts 37 foot rv. We towed from the northeast to the southwest this last september. Once arriving at our destination and placing the rv in storage I began researching the brake set up. The manufacturer of the axles lippert components, inc had put out a notice that affected my rv. The notice described an anomaly during the assembly process where too much wheel bearing grease was introduced to the hub assembly. This caused the seals to fail...

Read the full complaint

allowing the grease to contaminate the critical brake components. More specifically the brake linings, activation magnets and the corresponding surfaces of the brake drum the come in contact with. This diminishes the effectiveness of the braking action severely. Under the right circumstances could prove disastrous. Even fatal to not only the driver and passenger of the tow vehicle but any other people traveling on the same highway with the rv in close proximity. Lippert acknowledged the problem with me and sent replacement brake shoe assemblies and seals for all (4) wheels. Not including the brake drum, or bearing assemblies. Or labor to install the new components. The wheel assemblies have never been removed from the rv since new. Until the installation of the new components began I had never seen the extent of excess grease contamination I was traveling down the highway with. Please refer to the attached photos. This may very well be an unresolved issue on other rvs on the road with these lippert axle assemblies. No one ever contacted me regarding this issue. Not the rv manufacturer or lippert. I had to research this anomaly on my own. Please make others aware of the extremely dangerous situation on the brakes of other unassuming rv owners traveling on our highways.

Filed Incident Service brakesNHTSA 11153382
2017 Grand Design ReflectionBrakes

During mostly highway travel with our camper the axle grease seals failed which allowed grease to contaminate the brake shoes and brake drums affecting braking performance. Reviewing other posts on-line a lot of other owners of these campers are experiencing the same problem, which is a significant safety issue.

Filed Incident Service brakesNHTSA 11118831
2016 Grand Design ReflectionSuspensionBrakes

In august of this year, I purchased a 2016 grand design reflection 313rlts travel trailer (used) from a grand design dealer (palm beach rv, west palm beach, fl). Vin: [[redacted]]. I have driven this trailer approximately 2,000 miles. I noticed that the trailer wasn't braking as good as it should be, so I took it in to a local rv repair shop (rvtech, ft. Myers, fl) to have it checked out. Upon inspection, they discovered that all four of my grease seals have failed, and that the backing plates and brakes were...

Read the full complaint

splattered with grease, the drum assemblies were scored, the brake pads were damaged and needed repair. He also said it appeared that the magnets were actually digging into the metal, creating further scoring. I'm not a mechanic, but their explanation of the damage that was done was that it was a direct result of the grease seals failing. After researching on the internet I discovered that this is indeed a very well known problem - the grand design owner's forum has 92 pages on a single thread about it. I'm very disappointed that this appears to have been a known problem, and I've been driving a 10,000 lb trailer with basically no brakes. Why didn't grand design notify their dealers of this problem, and have the dealers check to see if any of their customers had this problem? Information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr

Filed Incident Suspension · Service brakesNHTSA 11061282
2016 Grand Design ReflectionBrakes

Over packed wheel bearings from factory causing grease to be forced past rear wheel bearing seals and contaminating electric brakes. Brake effectiveness severely compromised causing difficulty in stopping 5th wheel trailer. Problem should have been found by selling dealership during it's first warranty inspection but was ignored or overlooked. (Tom stinnett's campers inn rv in louisville ky) first contact with company, dealership denied working on the rv at all, then later said they did in april of 2017. Then...

Read the full complaint

claimed that they only looked at one wheel. That wheel and the other three were badly contaminated with grease. We trust that factory trained service techs will know what to do and protect the general public from safety issues but in this case they ignored the blatantly obvious problem. Heavy grease accumulation on the wheel rims is a dead give away of the problem and does not require any effort to inspect, yet nothing was done. (First detected during transfer of ownership to me on 8/16/2017)

Filed Incident Service brakesNHTSA 11020281
2017 Grand Design ReflectionBrakes

The brakes, seals and bearings on my 5th wheel travel trailer will have to be replaced for the third time due to the seals leaking grease onto the brakes. All four backing plates, the front two hubs and all four grease seals and bearings were replaced on our first trip after taking possession of the fifth wheel in may 2017. This was done at a camping world dealership in north carolina and resulted in being without the use of our trailer from may 18 ' 23. On our second trip, starting on july 9, 2017, the...

Read the full complaint

brakes again began performing poorly. Ray duffy, of grand design, arranged to have them inspected in west yellowstone, montana on july 14, 2017 at jake's automotive. He pre-shipped replacement parts in anticipation of bad seals. The technician at jake's automotive found grease contamination on the right front, right rear and left rear brakes. He also found that those seals and bearings had separated from the hubs and remained on the spindle when the hubs were removed. The receipt states, 'had to replace 3 of four backing plates and hardware due to wheel seals blowing out.' The fourth wheel, the left front, was not removed or inspected by the repair facility since they did not have replacement parts available and they were concerned that removal of the wheel could damage the grease seal. I removed all four hubs today. The interiors of the two left hubs were completely coated with grease. The left front was worse than the left rear. The two right hubs did not have as much grease on them and were evidently doing the majority of the braking. The inside of both hubs were pretty severely scored by the magnets and need to be replaced. All four grease seals and the inner bearings stayed on the spindles when the hubs were removed. Since the seals are supposed to be pressed in, I found their remaining on the spindles problematic.

Filed Incident Service brakesNHTSA 11016116

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience