- The problem
- On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.
- The risk
- Seizure of the bearings can cause wheel separation or wheel end fire.
- The fix
- Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940-591-4201 or kenworth 425-828-5440.
Vehicle safety record
1999 Kenworth T600 Problems, complaints & recalls
Owners have filed 1 complaint about the 1999 Kenworth T600 with NHTSA, most often about the transmission & drivetrain (1). It is covered by 9 recalls, the latest in April 2003 for the hub. For comparison, the 1998 has 0 and the 2000 has 0.
NHTSA data checked
DMore problems than a typical T600 year, for its age
#425 most complained-about 1999 vehicle
- Complaints
- 1
- Recalls
- 9
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Most common 1999 Kenworth T600 problems
Share of all 1 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
1999 Kenworth T600 recalls 9
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4201 or kenworth at 1-425-828-5440.
- The problem
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with tie rod assemblies manufactured by trw. The suspect tie rods contain 24-dl model ball sockets. Certain of the tie rod ball-socket bearings have a below-specification case depth and/or hardness, which can lead to premature wear of the socket.
- The risk
- If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash.
- The fix
- Dealers will replace the defective ball sockets and/or drag links. Owner notification began on april 10, 2001, to kenworth owners and on April 25, 2001, to peterbilt owners. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000, peterbilt at 1-940-591-4000 or trw customer service at 1-866-280-3287.
- The problem
- Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
- The risk
- Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
- The fix
- Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.
- The risk
- If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.
- The fix
- Dealers will inspect and correct the problem, as needed. Owner notification began february 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends.
- The problem
- Vehicle description: heavy duty trucks. The installation of the aluminum steering driveline exceeds the u-joint angles specified by dana, the driveline manufacturer. By exceeding this specification, the u-joint could contact and cause a stress riser in the aluminum drive shaft. This contact could cause in a notch in the aluminum drivement, resulting in a stress riser in the shaft.
- The risk
- This notch could cause premature failure of the steering driveline, resulting in loss of vehicle control and/or vehicle crash without prior warning.
- The fix
- Dealers will replace the aluminum driveline with a steel version.
- The problem
- Vehicle description: heavy duty trucks equipped with caterpillar engines and eaton autoshift transmissions. The engines can stall because of software problems.
- The risk
- INCREASED STEERING EFFORT CAN OCCUR.
- The fix
- Dealers will update these engines with software changes. Caterpillar is conducting the owner notification and remedy of this recall.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
1 complaints about the 1999 Kenworth T600
Newest first, as filed with NHTSA by owners.
During normal operation of vehicle, there is a noise being emitted from rear due to gears in rear have become stripped. Manufacturer has informed consumer that this defect was due to "shock load" (driver abuse). *Ak *slc
Kenworth T600: every year compared
All T600 years1999 Kenworth T600 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1999 Kenworth T600 | 1 | 9 | D | |
| 1999 Kenworth T800 | 4 | 12 | D | Compare |
| 1999 Kenworth W900L | 4 | 0 | D | Compare |
| 1999 Kenworth W900 | 3 | 10 | C | Compare |
| 1999 Kenworth Kenworth | 3 | 2 | D | Compare |
| 1999 Kenworth T2000 | 2 | 8 | D | Compare |
| 1999 Kenworth Conventional | 2 | 0 | D | Compare |
| 1999 Kenworth C500 | 1 | 7 | F | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1999 Kenworth T600
Does the 1999 Kenworth T600 have any recalls?
Yes - NHTSA lists 9 recalls for the 1999 Kenworth T600: hub (April 2003); tie rod assembly (July 2002); tie rod assembly (August 2001); tie rod assembly (March 2001) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 1999 Kenworth T600?
By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (1).
How many complaints has the 1999 Kenworth T600 had?
1 complaints have been filed with NHTSA, the first on April 12, 2001 and the latest on April 12, 2001. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.
Is the 1999 Kenworth T600 a reliable vehicle?
Its Safety Index is 28 out of 100 (grade D: more problems than a typical Kenworth T600 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T600 years have the most complaints?
2005 (4), 1997 (2), 2003 (2). See every Kenworth T600 year compared.
What should I do if my 1999 Kenworth T600 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data