PACCAR Incorporated (PACCAR) is recalling certain 2027 Kenworth T280, T380, T680, T880, and W990 vehicles. The drivelines may be missing a snap ring in the slip yoke assembly, causing the bearing cup to separate from the driveline.
Transmission & drivetrain
Kenworth T680 Transmission problems by year
17 complaints filed with NHTSA about the Kenworth T680's transmission & drivetrain. Harsh or delayed shifting, slipping, CVT shudder, rollaway, axles, driveshafts and transfer cases.
Transmission complaints by model year
Transmission recalls
PACCAR Incorporated (PACCAR) is recalling certain 2021-2024 Peterbilt 365, 367, 389, 535, 536, 537, 548, 567, 579, and 2021-2025 Kenworth T180, T280, T380, T480, T680, T880 and W990 trucks. The right-hand gear shifter stalk connectors may have been...
PACCAR Incorporated (PACCAR) is recalling certain 2018-2019 Peterbilt 337, 348, 365, 367, 389, 567, 579 and 587 trucks and 2018-2019 Kenworth C500, T270, T370, T440, T660, T680, T800, T880 and W900 trucks equipped with automated manual transmissions. An...
PACCAR Incorporated (PACCAR) is recalling certain 2018 Peterbilt 567, 579, Kenworth T680, and T880 trucks, equipped with certain Eaton Endurant and PACCAR AMT transmissions. The transmission control module (TCM) may allow the engine to crank briefly even if...
Paccar (Paccar Incorporated) is recalling certain 2016 Kenworth T680, T800, and T880 trucks manufactured January 5, 2015, to January 7, 2015 and 2016 Peterbilt 367, 384, 567, and 579 trucks manufactured January 2, 2015, to January 9, 2015 and equipped with...
PACCAR Incorporated (PACCAR) is recalling certain model year 2014 and 2015 Kenworth T660, T680, and T800 trucks manufactured January 29, 2013, to April 2, 2014, and 2013 Peterbilt 587 trucks manufactured on August 8, 2012. The affected trucks are built with...
PACCAR Incorporated (PACCAR) is recalling certain model year 2015-2016 Kenworth T680 and T880 trucks manufactured November 17, 2014, to January 5, 2015. The affected vehicles are equipped with Meritor MT-40-14X rear drive axles that may circulate an...
Latest T680 transmission complaints
I have 2 Kenworth trucks VIN [[redacted]] and [[redacted]] both on recall NHTSA 24V190. The recalls have been performed my issue is with reimbursement for prior replacement for the recalled parts. I have attached emails from Paccar as well as the invoices for the replacement of the recalled parts. Any help you can provide is appreciated as I'm not getting anywhere with Paccar or the dealers. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am reaching out to you for this recall #24KWE, for the right hand stalker shifter. My truck is a 2024 kw t680. I am having this issue with my truck multiple times now and when I brought it to my dealer mhc of mcdonough,ga they said this recall is no longer active but we are having this major issue which can cause an accident at no giving time when the vehicle stops and is disabled.please reach out to me about this situation,also my truck only has 88,205 miles as of today.the estimated quote was done by the service shop to do the job which alot of kenworth owners went thru.thank you
When I was driving on the highway the transmission fault error came on and my truck came to a stop on on the highway. It changed gears weirdly and kept the rpm's high. Once it came to a stop I turned the truck off and on and it work fine. This has happened multiple times and a nationwide failure of the MTM and transmission is the cause of this. Many of my fellow drivers are having this same issues and are having to replace the whole transmission due to the MTM failing and destroying the transmission.
The Eaton 12 speeds that these trucks come equipped with are failing just after the warranty expires. Lots of drivers with the same problem.
Right-hand shift stalk between the shifter and the transmission is causing the vehicle to become disabled while stopped and unable to go from forward to reverse. Also getting SPN 639 pop-up when communication has been lost between the engine control module (ECM) and SAE J1939 data link. The check engine light illuminates, and the ECM immediately logs the fault code. Have to depress brake pedal while stopped & cycle gear selector to get fault to clear to start engine . Message also displayed Transmission Fault Repair Required Find Service Center . Also had new spring clutch replaced in May of 2024. Truck has 525k miles on it .
The clutch Spring on these trucks have been failing heavily. We have a couple more of these trucks and they all have the same issue. the housing for the clutch springs are cracked or damaged at less than 500,000 miles on a heavy duty truck. These clutches are supposed to last over 1MM miles. Its not a coincidence that every truck we have is failing at the same mileage. These clutches are made defective from the manufacturer. Its also a coincidence that the replacement clutches are not the original design and are of a newer design and brand. THIS is RED FLAGS!!!!
The contact owns a 2023 Kenworth T680 with the camper attached. The contact stated that the ABS warning light was illuminated before the failure. The contact stated that while standing behind the passenger side seat in between the sleeper portion and the cab, there was an abnormally loud popping sound detected. The vehicle began to move and crashed into the door of an unknown tractor-trailer cab. The vehicle had been parked for approximately 45- 60 minutes before the crash. The contact had to seek medical...
Read the full complaint
assistance from a therapist due to the incident. There was no report of fire, airbag deployment, or police report filed. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 25,000.
My circumstances are EXACTLY as described in a release 12/19/2019 Tech Service Bulletin A002 I experienced the vibration in my steering wheel that caused me to be suspect that there was something wrong in the drive train. Upon further investigation. I noticed that an oil seal was leaking, and when I dug a little deeper, I noticed gears that were broken and shaved down and then stopped at a Kenworth corporate location upon which they told me that I needed to purchase the entire unit to fix it. I then decided that I...
Read the full complaint
was going to add some differential oil and drive at a speed of 45 miles an hour, which did not cause any vibration to Chicago, which was roughly 3 hours away from my location in Michigan upon which I would have more resources at my disposal. It is then that I learned of the technical service bulletin relating to my issue. I then took it to CIT trucks which is where I learned that you do not have to buy the complete unit that. The parts are available to be purchased to fix the issue. They did, however say that they would process the claim on behalf of this technical service bulletin. They advised me that the individual that they got a hold of seem to have an attitude about it and sometimes this happens whereas other times they will get a hold of somebody that will make an exception. Apparently they stated my situation is two months out of warranty from when my tractor was placed into service but it's original owner. I am not in a position due to other issues that I have experience with the truck since purchasing it in June that I can afford this but more importantly, there is a known issue with the same exact identical problem that I experienced. I need help with my situation they need to be held accountable for what has gone wrong because it is not my fault.
The contact owns a 2023 Kenworth T680. The contact received notification of NHTSA Campaign Number: 24V190000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall. The contact stated that while driving at an undisclosed speed, the transmission was not operating properly. The contact stated that the vehicle downshifted unexpectedly with the transmission fault...
Read the full complaint
warning light illuminated. The vehicle was restarted; however, the failure recurred. The dealer was contacted; however, the vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 338,388. The VIN was not available.
The clutch has a loose spring, Fork is damaged. Throwout bearing worn.
Throw out bearing failed prematurely. Truck only has 491,000 miles and has had a catastrophic failure resulting in a $29,000 repair bill. I have 4 other trucks like this and they are all showing signs of the same thing.
We bought this truck with 401, 000 miles on it. So far we have had to replace the rear ends twice. the whole DPF system, the check engine light still on since the day we bought the truck. We have had 5 NOS sensors put into the truck, 6 input and output sensors put into the truck. This truck has been defective since the day of purchase. We keep having the same error code of p3770 come up evetime we take to shop. The error code has been looked at so many times that even the master techs don't know what is wrong with the truck other then we keep replacing the same stuff over and over again.
The contact owns a 2023 Kenworth T680. The contact stated that the dealer previously repaired the vehicle under NHTSA Campaign Number: 22V547000 (Steering). The contact stated that while driving at an undisclosed speed, the ABS, traction control, transmission, and hill assist warning lights illuminated. The dealer was made aware of the failure but provided no assistance. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 109,000.
Unit had clutch failure failed to disengage under 18e-102, per federal guidlines it falls under the clutch range of au1704192065 and falls under eatons original campaign release but they revised it to where it does not cover this one becuase now they changed the range to au1711 thru au1804 but we are seeing a lot of failure below au1711, why does eatons document not match the federal documents? And why are we seeing these clutch failures on trucks that were revised and said to now be good, but they are failing in the same manner
A vibration is felt during warm up and becomes very noticeable after shifting into 8th gear. If the air compressor kicks in while the engine is below 1300 rpms this also increases the vibration , again real bad shifting into 8th and air compressor running .Note: I just bought this truck from kenworth sales company , salt lake city, ut I aint even put 2,000 miles on the truck, what kinda of deceitful ethics violations are practiced from this dealership?
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data