- The problem
- On certain trucks equipped with parker single check valves (scv) provided by bendix. The defect exists in the parker scv that connects with the supply port of the sr-7 spring brake modulating valve. After prolonged use of the parker scv, the valve body retainer may become excessively worn and eventually break apart. Pieces of the parker scv can become lodged inside the sr-7 spring brake modulating valve, potentially causing either leakage out of the sr-7 valve or preventing air from properly exhausting from the sr-7 valve.
- The risk
- This condition can cause a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button. These conditions can occur without warning, leading to unintended vehicle rollaway, brake drag, or in the case of loss of primary circuit, inability to modulate the spring brakes.
- The fix
- Mack is working with bendix to replace the parker single check valve. The recall began on january 9, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
Brakes
2007 Mack CHN Brake problems
No owner has filed a complaint about the 2007 Mack CHN's brakes with NHTSA. Spongy or hard pedal, ABS faults, brake failure, noises, parking brake and brake fluid leaks.
- Complaints
- 0
- Recalls
- 5
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Brake recalls for the 2007 Mack CHN
- The problem
- On certain trucks equipped with bendix sr-7 spring brake modulating valves, the internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
- The risk
- This could delay or failure in applying the parking brakes which could result in a vehicle roll away, increasing the risk of a crash.
- The fix
- Mack is working with bendix to repair these vehicles (please see 07e037). Bendix will install a check valve repair kit for the affected sr-7 spring brake modulating valve free of charge. The recall began on january 10, 2008. Owners may contact bendix at 1-440-329-9000 or mack at 1-800-528-6586.
- The problem
- On certain trucks, the brake cam tubes on the steer and drive axles may not have been greased.
- The risk
- The brake cam journals may corrode which may lead to the brakes dragging which could result in a vehicle fire.
- The fix
- Dealers will add grease to the brake cam tubes free of charge. The recall began on september 29, 2006. Owners may contact mack at 1-800-866-1177.
- The problem
- On certain trucks equipped with a legris air manifold, the brass push-to-connect cartridge may unexpectedly separate from the plastic housing.
- The risk
- If the push-to-connect cartridge that supplies the air to the park brake chambers were to separate, then the brakes could unexpectedly apply increasing the risk of a crash.
- The fix
- Dealers will replace the air manifold free of charge. The recall began on september 27, 2006. Owners may contact mack trucks at 1-800-528-6586.
- The problem
- On certain trucks equipped with sr-7 bendix brake valves, the check valve inside the valve cavity may not properly set, causing internal air leakage. If the check valve does not properly seat, the resulting leakage can cause a delay in the application of the spring brakes to park the vehicle after operator pulls the dash valve button.
- The risk
- The delayed parking brake application can occur without warning, leading to unintended vehicle rollaway increasing the risk of a crash.
- The fix
- Dealers will inspect the valves and replace it free of charge. The recall began on august 14, 2006. Owners may contact mack trucks at 1-800-528-6586.
Brake complaints
No complaints about this area yet.
Mack CHN brake complaints by year
CHN brake problems, every yearSource: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data