- The problem
- Mazda is recalling certain model year 2008-2009 mazda3 and mazdaspeed3 vehicles manufactured from january 7, 2008, through november 28, 2008. The ground terminal of the windshield wiper motor may have been inadvertently bent during assembly. If this condition exists then over time the electrical resistance of the motor circuit may increase up to a point that the windshield wipers would not work.
- The risk
- The loss of wiper function in adverse weather could potentially increase the risk of a crash.
- The fix
- Dealers will install an additional ground harness on the wiper motor free of charge. The safety recall is expected to begin on or before july 15, 2011. Owners may contact mazda customer assistance center at 1-800-222-5500.
Vehicle safety record
2008 Mazda MAZDASPEED3 Problems, complaints & recalls
Owners have filed 33 complaints about the 2008 Mazda MAZDASPEED3 with NHTSA, most often about the transmission & drivetrain (23) and the engine & cooling (5). Those complaints describe 1 crash, 2 fires and 2 injuries. It is covered by 1 recall, the latest in June 2011 for the motor. For comparison, the 2007 has 38 and the 2009 has 0.
NHTSA data checked
FFar more problems than a typical MAZDASPEED3 year, for its age
#195 most complained-about 2008 vehicle
- Complaints
- 33
- Recalls
- 1
- Crashes
- 1
- Fires
- 2
- Injuries
- 2
- Deaths
- 0
Most common 2008 Mazda MAZDASPEED3 problems
Share of all 33 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2008 Mazda MAZDASPEED3 recalls 1
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
33 complaints about the 2008 Mazda MAZDASPEED3
Newest first, as filed with NHTSA by owners. Page 1 of 2.
I was driving on a city road doing 35-40mph in 4th gear. I let off the gas while in 4th and coasted to about 20mph then shifted to n and stopped at a red light. When the light turned green I tried to shift to 1st an the shifter went half way in between r and 1st, so I shifted back to n and tried 1st again. Then the whole shifter broke off and was just laying there. Now my car is stuck in 3rd gear.
I was on the highway in motion when all of a sudden my shifter broke off and I wasn't able to move. I had to call I tow
I began to accelerate my mazdaspeed 3 shifting from 1st gear to second gear. I shifted into third where my shift broke and remained in my hand. My car stalled out in 3rd because I could not shift out. I took off the plastics covering the shifter and pulled the plate back into neautral so I could push my car to the local gas station. My shifter rod snapped and the spring came out.
Manual shift lever came detached while driving in rush hour traffic. Car stuck in 4th gear. I was up shifting when it happened.
While shifting from 2nd to 3rd gear at low speed, the shifter for my manual transmission broke off in my hand. After coasting to the side of the road and removing the console, I discovered it snapped in half at the location of the retention pin.
As I was slowing down to make a right turn I placed the car in neutral. After making the turn and going to put the car back in gear the shifter breaks at the point where the pin goes in above the ball. I do not track my car nor shift hard ever. *Tr
The shift lever complete broke off and no longer had any affect on engaging any of the gears. I was stopped at a light and it broke when I tried to engage 1st gear out of neutral. Luckily I was able to feel for the shift cable mechanism through the leather shifter boot and engage 3rd gear. Limped home in 3rd. *Tr
I have a 2008 mazdaspeed 3 with a manual transmission. While I was driving to work on 9/9/2014, the steel rod that the shifter knob is attached to sheared off suddenly while I was shifting from first to second. This left the transmission in neutral and I had no power since I couldn't shift into gear. This was a very dangerous situation since I was traveling through an intersection in heavy traffic. Luckily, I avoided an accident and coasted to a stop. The car had to be towed home. The steel shaft separated...
Read the full complaint
completely in two without any warning. The break occurred right where the shaft has a hole drilled through it for the metal pin that locks it into the lower part of the shifter assembly. I have saved the broken part and I also took photos of it at the time of the incident. I'm very concerned that this part, which is critical to the safe operation of the vehicle failed without warning while I was driving. This appears to be a serious design or manufacturing defect. There are other reports of similar shifter failures for this year/model car on internet forums. I reported this problem to a mazda customer service representative via mazda's customer experience hotline on 9/9. I emailed them a description of the problem and sent photos of the part. I also showed the part to my local mazda dealership, lee johnson mazda in kirkland, wa and they confirmed that the part should not have failed in this fashion. I have made repeated follow up calls to the mazda customer experience hotline and on 9/26 they have informed me that mazda will not investigate the issue and is not interested in examining the failed part. The case file number they gave me is [[redacted]]. Information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr
While shifting from 2nd gear to 3rd gear, shifter lever sheared, and detached, at the retaining pin. *Tr
Stopped at a stoplight, I attempted to shift in to first gear. While shifting, the transmission select lever sheered at the insertion point to the transmission at the retention pin. I was left with a stick shift that was completely removed from the car and immobile. *Tr
Defective engine/transmission mount. Driving home at 45mph I suddenly felt a huge thunk and then metal pounding against metal as the car rolled. I was in the left lane of a 2 lane road and when I pressed the gas pedal to pull to the side safely all I could hear was a terrible thumping noise and the car wouldn't move. I had to stop in the left hand turn lane blocking a busy intersection. After having the car towed home I could finally pop the hood to look at the damage. The #4 (driver side) engine and transmission...
Read the full complaint
mount had completely failed, breaking the rear engine mount (#1) and severely damaging the #3 (passenger side) engine mount. The only thing keeping the engine from falling to the ground was the severely damaged #3 mount and the rest of the engine had landed on the chassis! Picture of broken engine/transmission mount - http://i.Imgur.Com/mwtnubd.Jpg explanation of repairs at my local mazda dealership: "customer states motor mount is broken, engine has shifted. Check and advise. Tow in. Verified customer concern, found transmission mount has failed causing engine to drop and break left axle. Also caused damage to engine mounts #3 and #1. Replaced left front axle. Transmission motor mount #3, and #1. Test drove vehicle, repair verified" mazda has a recall for this exact issue for all mazdaspeed3s manufactured june 2006 through may 2007. My car was manufactured in september of 2007, 4 months after the recall expired... Nhtsa campaign number: 07v295000. Mazda recall number: 4607f. $1500 And 2 weeks later I have my car back. I called mazda usa and filed a complaint and was told they would do nothing to help. Mazda knows that they have defective engine mounts in mazdaspeed3 vehicles manufactured after their recall expired. There are many additional complaints all over the web and in the nhtsa database yet mazda has done nothing. Mazda complaint number: 149448083. *Tr
Shifted from 1st to second gear, shifter snapped in half. Told be dealer that replacement shifter is on "galactic back order." *Tr
Tl* the contact owns a 2008 mazda speed 3. The contact stated that while driving 65 mph, the tpms sensor light illuminated and the front driver side tire blew out. The contact was able to pull to the side of the road. The contact towed the vehicle to the dealer. The dealer stated that the tpms sensor had fractured and caused the blow out. The dealer also stated the remaining tpms sensors were also fractured. The contact called the manufacturer and filed a complaint. The failure mileage was 42,000.
Tl* the contact owns a 2008 mazda, mazdaspeed3. The contact stated that while attempting to shift into reverse, the gear lever became fractured. The vehicle was coasted to a safe location where a temporary repair was performed by the contact. The vehicle was then taken to an independent mechanic, who stated that the gear shift assembly would need to be replaced. The part was ordered for the repair. The manufacturer was not made aware of the defect. The approximate failure mileage was 85,000. The vin was unavailable.
Was stopped at a stoplight. When the light changed, I went to put the car in first gear and the stick shift lever broke in half. Disassembling the shifter console for examination, it appears that the shaft has broken cleanly in half at the point where it is drilled for the reverse lockout pin. *Tr
As I was driving on the freeway, I heard a loud pop and then a flopping noise. I pulled over to the shoulder and noticed there was oil leaking from the undercarriage and white smoke. After having the vehicle towed to the dealer, it was determined that the transmission was destroyed. After the transmission was removed, the repair technician showed me the transmission, which was literally breaking in pieces. He said that I would also need a new clutch assembly and flywheel. I don't understand how this could have...
Read the full complaint
happened. I do not abuse the car and maintain it well. I wasn't even shifting gears at the time of the incident. Just driving along in 6th gear. Unfortunately, this happened less than a month after the warranty expired (of course) and mazda would not help cover any costs for the repairs. *Tr
Coming up towards a stop sign on put the car in neutral like always hit brakes stop at the stop sigh then attempt to shift to 1st and the shifter just falls out. Lucky for me I was 2 stop signs from my house so I was able to put take the shift boot out and get the car into 2nd and make it home. *Tr
While shifting from 2nd to 3rd gear my shift stalk fell off in my hands. I had to turn my emergency blinkers on and pull over without being able to shift gears. I was able to reach below the shift boot and feel the shifting base mechanism to move the car back in to gear once off of the road. I am currently unable to drive the car as the shift control will not stay in place. *Tr
The shift lever broke off during a shift while driving, making it impossible to shift gears after this occurred. The fault seems to lie in the design. There is a hole in the lever to accommodate a pin which prevents accidental shifting in reverse. However the hole in the lever is a weak point and it is easy to see how the lever sheared off at that point. This problem has been reported by other drivers via online message boards. Currently there is no recall. This failure is extremely dangerous and I was lucky enough to be able to pull off the road. However, this could have easily resulted in a collision. *Tr
I got into my car and went to put it into reverse and it stuck alittle. Usually, I can move it slightly and it will go into gear but this time it just snapped and fell over into my lap. *Tr
Broken shift lever. Coming off of freeway, downshift to third and it snapped. Shift lever broke at a known stress point in the design. Right at the bottom of the lever where the reverse lockout pin is located. The manufacturer is claiming this is not covered under powertrain warranty. While I did have it replaced under the bumper to bumper warranty, others who are out of the standard warranty are being denied replacements even though they are still covered under the powertrain warranty. This is unacceptable as...
Read the full complaint
this is a known flaw and could lead to accidents in the future. Having a manual transmission gear shifter break off in your hand while driving is extremely dangerous and demands immediate attention. Now, seeing that you can't operate the vehicle without the shift lever, that should automatically qualify it as powertrain. Let's be logical here. *Tr
When driving at highway speed for an extended period of time, something in the turbo exploded causing the engine to fail and a loss of power in highway traffic. *Js
When driving at highway speed for an extended period of time, the excessive wheel camber made the tire heat up and wear through on the inside edge, and blow out. This happened again the next day. *Js
I went to shift into first gear from a stop (at a red light,) and my shifter fell off in my hand. Upon disassembling the center console at the light, I found that the cast-aluminum shifter arm had broken at the insertion point for the retention pin. Not only am I not the only one with this issue, but it happened to another person today (whom I'm forwarding to this site.) Mazda said it's not under the powertrain warranty and because I have an aftermarket transmission mount and a cold-air intake, they won't make...
Read the full complaint
a goodwill adjustment (in spite of the fact that neither of those things would break it....) They have no concern over the clear safety issue, refuse to discuss other incidents and spoke to me as if this is the first car I've owned and my time would be better spent coloring on the bus. *Tr
Most cars have two horn tones, a "low" and a "high." For the us market, the mazda3/speed3 deletes the "low" tone. The remaining "high" tone is too weak to be heard by surrounding motorists. I have added an aftermarket low tone and have lost count of how many times this upgrade has prevented a crash. Which makes me wonder how the nhtsa allowed mazda to sell cars in the us with such worthless horns? *Tr
Mazda MAZDASPEED3: every year compared
All MAZDASPEED3 years2008 Mazda MAZDASPEED3 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2008 Mazda MAZDASPEED3 | 33 | 1 | F | |
| 2008 Mazda MAZDA3 | 303 | 3 | F | Compare |
| 2008 Mazda Tribute | 202 | 5 | C | Compare |
| 2008 Mazda Tribute Hybrid | 202 | 0 | F | Compare |
| 2008 Mazda CX-7 | 192 | 5 | C | Compare |
| 2008 Mazda CX-9 | 172 | 6 | F | Compare |
| 2008 Mazda MAZDA6 | 111 | 5 | C | Compare |
| 2008 Mazda MAZDA5 | 67 | 2 | D | Compare |
| 2008 Mazda RX-8 | 17 | 5 | B | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2008 Mazda MAZDASPEED3
Does the 2008 Mazda MAZDASPEED3 have any recalls?
Yes - NHTSA lists 1 recall for the 2008 Mazda MAZDASPEED3: motor (June 2011). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2008 Mazda MAZDASPEED3?
By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (23), engine & cooling (5), electrical system (2).
How many complaints has the 2008 Mazda MAZDASPEED3 had?
33 complaints have been filed with NHTSA, the first on August 1, 2008 and the latest on April 13, 2018. Of these, 1 describe a crash and 2 a fire, and together they report 2 injuries and 0 deaths.
Is the 2008 Mazda MAZDASPEED3 a reliable vehicle?
Its Safety Index is 12 out of 100 (grade F: far more problems than a typical Mazda MAZDASPEED3 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Mazda MAZDASPEED3 years have the most complaints?
2007 (38), 2008 (33), 2010 (32). See every Mazda MAZDASPEED3 year compared.
What should I do if my 2008 Mazda MAZDASPEED3 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data