Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2007 Mazda MAZDASPEED3 Problems, complaints & recalls

Owners have filed 38 complaints about the 2007 Mazda MAZDASPEED3 with NHTSA, most often about the transmission & drivetrain (17) and the engine & cooling (15). Those complaints describe 1 crash. It is covered by 2 recalls, the latest in July 2007 for the engine and engine cooling. For comparison, the 2008 has 33.

NHTSA data checked

FFar more problems than a typical MAZDASPEED3 year, for its age

#174 most complained-about 2007 vehicle

Complaints
38
Recalls
2
Crashes
1
Fires
0
Injuries
0
Deaths
0

Most common 2007 Mazda MAZDASPEED3 problems

Share of all 38 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2007 Mazda MAZDASPEED3 recalls 2

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Engine and engine cooling

07V2950005,700 vehicles affected

The problem
On certain passenger vehicles, the no. 4 Left side engine mount bolt may loosen if a sudden rapid acceleration is repeatedly performed.
The risk
If the vehicle is continuously driven under such condition, the no. 4 Engine mount bolt may loosen and pull out or break, allowing the transmission to be out of position. In extreme cases, the drive shaft may become detached. If this occurs the vehicle will lose power and will come to a stop, increasing the risk of a crash.
The fix
Dealers will inspect and replace the no. 4 Engine mount bolt with a modified one, and, if necessary, replace the no. 4 Engine mount rubber and bracket with new ones free of charge. The recallbegan on july 13, 2007. Owners may contact mazda at 800-222-5500 .

Equipment

07V0520001,700 vehicles affected

The problem
On certain passenger vehicles equipped with optional accessory all weather floor mats, there is insufficient clearance between the floor mat and accelerator pedal.
The risk
In this situation it is possible that the accelerator pedal might get stuck behind the floor mat, which may prevent the vehicle from properly decelerating when the accelerator is released increasing the risk of a crash.
The fix
Owners will be instructed to return the floor mats to dealers and will be shipped a new floor mat free of charge. The recall began on march 7, 2007. Owners may contact mazda at 1-800-222-5500.

What owners say

Be the first MAZDASPEED3 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

38 complaints about the 2007 Mazda MAZDASPEED3

Newest first, as filed with NHTSA by owners. Page 1 of 2.

Acceleration & cruise control

I was driving on the freeway on my way to work and I was going about 70 mph when the car suddenly and violently jerked and dropped into 3rd gear from 5th gear.It happens at random times my a.T. Light and check engine light came on and now my car is stuck in 4th gear. I have had my transmission flushed and my speed sensor replaced but im still having issues with it I dont like to take my kids in my car due to the fact that it is very dangerous when that does occur I am scared that I am going to get into a car...

Read the full complaint

accident due to this issue. I bought the car from a used dealership in fontana ca on april 19 2016 the very next day the car started to trip up from 4th to 3rd gear. The a.T light came on and since then it has gotten worse I called the gentleman who sold me the car and told him what was going on with the car he told me to bring it in and have the fluids flushed and it was probably just a sensor . So I took it in and the drove fine for a little while then out of no where the car started to go from 5th gear to 3rd gear very violently so I replaced the output speed sensor and it still had the same problem. I had the transmission serviced again and the transmission filter replaced and my car is still going from 5th gear to 3rd gear eratically.

Filed Incident Vehicle speed controlNHTSA 10893328
Lights

Tail light dome assembly is melted by the bulb from both side. *Tr

Filed Incident Exterior lightingNHTSA 10649006
Transmission & drivetrainEngine & cooling

On saturday 19 july 2014, my wife and I were driving north on highway 131, 18 miles south of grand rapids, mi when without notice the engine's number 1 cylinder blow a hole through the casting and damaging the inner axle shaft carrier bearing. When the engine blew, it caused the car to shake violently causing me, the driver, to lose control of the vehicle. I was able to regain control of the vehicle before the car swerved into an adjacent lane. Prior to the incident the vehicle was in good running condition and had...

Read the full complaint

just passed the virginia state inspection a few months prior. All of the regular vehicle maintenance was completed according to the vehicles maintenance schedule. Each servicing that was completed was documented in my own personal records for reference. This being said, this vehicle caused a major safety incident without notice, which under certain circumstances could have caused serious damage or even a fatality. There are several cases of these mazda 2.3 Liter turbo mrz engines blowing under normal operating conditions. There is a major design or manufacturing defect which mazda needs to address. *Tr

Filed Incident Power train · EngineNHTSA 10625871
Transmission & drivetrainEngine & cooling

On saturday 19 july 2014, my wife and I were driving north on highway 131, 18 miles south of grand rapids, mi when without notice the engine's number 1 cylinder blow a hole through the casting and damaging the inner axle shaft carrier bearing. When the engine blew, it caused the car to shake violently causing me, the driver, to lose control of the vehicle. I was able to regain control of the vehicle before the car swerved into an adjacent lane. Prior to the incident the vehicle was in good running condition and...

Read the full complaint

had just passed the virginia state inspection a few months prior. All of the regular vehicle maintenance was completed according to the vehicles maintenance schedule. Each servicing that was completed was documented in my own personal records for reference. This being said, this vehicle caused a major safety incident without notice, which under certain circumstances could have caused serious damage or even a fatality. There are several cases of these mazda 2.3 Liter turbo mrz engines blowing under normal operating conditions. There is a major design or manufacturing defect which mazda needs to address. *Tr

Filed Incident Power train · EngineNHTSA 10621872
Wheels & tiresCrash

I was using a michelin green x tire for about 2 years an mileage of 50000. In a 45 degree curve suddenly my tail went out of control and I ran into the middle separate of road,caused a lot of wreckage . I was told that this was because of low rear tire grip to the road. *Tr

Filed Incident TiresNHTSA 10549666
Engine & cooling

Tl* the contact owns a 2007 mazda mazda speed3. The contact stated that while traveling 65 mph, the engine suddenly failed. The vehicle was taken to a private mechanic where it was found that oil pressure module had failed. The vehicle was not repaired. The manufacturer was contacted about the failure. The failure mileage was 96,000.

Filed Incident EngineNHTSA 10532479
Suspension

Tl* the contact owns a 2007 mazda, mazdaspeed3. While driving approximately 30 mph on an uneven road surface, the contact heard a clunking noise coming from the front end of the vehicle. The failure recurred sporadically. The vehicle was not diagnosed or repaired. There was a technical service bulletin under nhtsa action number: 10023313 (suspension: front). The manufacturer was made aware of the problem. The approximate failure mileage was 41,000.

Filed Incident SuspensionNHTSA 10406246
Transmission & drivetrain

I own a 2007 mazdaspeed 3, purchased from a dealer in , langley bc., In june 2008. It was a us imported car ( by the dealer) and I was told I inherited the balance of the warranty. It was built in may 2007, and had approx 22,646 miles on the odometer. On friday 27 may at about 7 am, I had just accelerated from a traffic light when an engine mount suddenly failed, pitching the complete engine and transmission forward and down onto the road , with disastrous consequences. I was really fortunate to be...

Read the full complaint

traveling quite slowly ( about 20 mph) as the 'cv' joint disintegrated and the car slewed alarmingly towards the kerb. I did not have much directional control, but managed to steer the car towards the kerb where it (rapidly ) came to a stop. Fortunately, I was traveling slowly enough for this not to be serious accident, but if I had been traveling at 70 mph down the freeway, I might not have been here today to write this. I had to have the car towed to a mazda dealership ( at my expense ) where a inspection showed that the #4 engine mount had failed, dropped the engine and transmission and destroyed the 'cv' joint, in the process damaging the turbo wastegate valve. They checked the vin and found that the vehicle was indeed built may 2007, and that there had been a recall to change the engine mount, also in 2007 ( before I purchased the car). This change was presumably done at a us dealer as it did not come to the in bc dealer until just before I purchased it in 2008. There was absolutely no overt warning signs- the only thing was the day before when I noticed a faint vibration coming from the front , which sounded like a pipe clamp or something vibrating. I stopped and made a visual inspection of the engine bay and underneath , but could not see anything. Bang as it let go. The parts were replaced free under mazda warranty. *Tr

Filed Incident Power trainNHTSA 10405516
Brakes

Lifted parking brake lever to engage parking brake, and it came up way further than normal without offering the normal resistance. After three attempts at resetting the brake, it engaged normally. Malfunction occurred again later. *Tr

Filed Incident Parking brakeNHTSA 10376538
Transmission & drivetrain

On april 28, 2009 while driving home from work I shifted gears from second into third I heard a big thunk from the transmission. I stopped the car and looked under the body but did not notice any broken or loose parts. Occasionally in the past while driving the car the gear would slip and move into neutral, and I thought this might be related to that seemingly minor problem. However, as I started to drive I noticed the gears were very hard to change and clutch was not as smooth as it used to be. Early the next...

Read the full complaint

morning I took the car to o'brien auto park of urbana. This business is located at 1111 o'brien drive, urbana, il 61802 (telephone 217-367-1222). I spoke to josh berbaum, the service consultant for mazda o'brien, and explained to him what happened. On monday, may 4, 2009 and told me that the clutch has failed and the flywheel had hot spots and could not be repaired. He apologized and said this is 'wear and tear' and mazda would not cover it under new vehicle limited warranty or the powertrain limited warranty. He also stated that this is a very big job and would cost over $1575 in parts and $1045 in labor and that it would take a couple of days to fix the car. After o'brien kept the car for 10 business days I paid $2352.99 To get my car and mazda declined my claim. I have taken the issue with my credit card and let what they can do for me. *Tr

Filed Incident Power trainNHTSA 10277580
Transmission & drivetrain

2007 Mazdaspeed3. Driving 25 mph and suddenly huge load sound underhood followed by much clanking and knocking as I coasted to a stop on the side of the road. Car could not be rolled. Engine dropped 2-3 inches and driver side axle broke and dangled from wheel. Car went to shop and axle, cv joint, complete transmission, fan, and a variety of smaller parts all have to be replaced. Car is currently still in shop. *Tr

Filed Incident Power trainNHTSA 10264029
Engine & coolingTransmission & drivetrain

I have an 2007 mazda mazdaspeed3 bought in may 2007. I had the motor mount bolt replaced during an associated recall in august 2007. A few months later it failed (july 2008). The bolt had backed out, and sheared through the last few threads. I heard this loud bang, followed by clunk-clunk noises and immediately pulled over into a gas station. I was fortunate to be on the right lane at 30 mph in 3rd gear. I had it towed to jim ellis mazda of marietta (ga). They told me that the engineers from mazda had a look at it...

Read the full complaint

and the whole mount bracket and the bolt was replaced under warranty. But over the past two weeks I've been hearing a slight clunking noise especially during slow turns, so I took it back to the dealer again on last monday (03/02/09) to have them look at it. They found that the steering rack flow control valve was popping at times and replaced it under warranty. I had also asked them to have a look at my mounts, just to be sure. I got my car back on thursday and was told that my mounts were fine. But on friday (03/06/09) I still had those clunking sounds on slow turns and while pulling out of parking lots/backing up. I also noticed some odd vibrations on the clutch pedal while giving gas and during idle. The last time had these vibrations were just before the motor mount failed on me. So I decided to have a look into my mounts. I also noticed that my clock and trip meters were not reset. If the dealer had inspected my mounts they would've been reset when the battery is being removed. That raised my suspicions. I removed the battery and tried turning the mount bolt. It was I could turn it with just one hand. I immediately called the dealer and asked them what to do. The asked to bring the car over after tightening it, or get it towed if I couldn't. I tightened the bolt and it took me about 6 turns to fully tighten it!!! The bolt was almost out and I caught it before something serious had occurred. The dealer has re tightened the bolt now. *Tr

Filed Incident Engine and engine cooling · Power trainNHTSA 10261307
Engine & cooling

Had motor/transmission mount recall done on my 2007 mazdaspeed3 done as soon it released in 2007. Feb 2009 with 26000 miles on the car the motor/transmission mount bracket tore apart while driving. Axles, and alot of other parts, damaged. Needles to say thank god I was only doing 5mph when incident occurred. Car was repaired at mazda dealer, and before I picked up vehicle after supposedly being fixed, motor/transmission mount failed again while the mazda tech was driving vehicle. Mazda has a very serious problem...

Read the full complaint

with these cars that they do not seem to want to address properly. They really need to fix this problem now before someone gets injured seriously. Not an acceptable problem on any car. *Tr

Filed Incident Engine and engine coolingNHTSA 10258514
Transmission & drivetrain

Mazda speed 3 engine mount failure, engine fell out of b ottom of car. *Tr

Filed Incident Power trainNHTSA 10236548
Transmission & drivetrain

My transmission occasionally pops out of second gear when I let off the gas. *Tr

Filed Incident Power trainNHTSA 10233220
SuspensionWheels & tiresEquipment & accessories

I installed the aftermarket mazdaspeed lowering springs on my mazdaspeed3, carefully following the supplied instructions. The instructions require removing the bump stops from the strut mounts. I thought this was strange, but I did it, and later found that my right-front tire tread surface had made contact with the top of the inside of the fender. The result was deep circumferential grooves in the tire, and the plastic fender liner was completely worn away in one area. This is potentially very dangerous since it could lead to a tire blowout. And yes, I am certain that the instructions show the removal of the bump stops. I have the instructions and photos of the damage. *Tr

Filed Incident Suspension · Tires · EquipmentNHTSA 10224508
Transmission & drivetrain

At 8,811 miles the number 4 engine mount (driver's side transaxle to frame) failed even though recall 4607f had already been performed at 826 miles ~8 months ago. *Tr

Filed Incident Power trainNHTSA 10222709
SteeringWheels & tires

Tl*the contact owns a 2007 mazda speed 3. While driving less than 10 mph, the vehicle went into a full skid and struck a curb. Five miles later, the vehicle lost steering ability and the wheel turned completely around. The vehicle was taken to a dealer and they replaced the failed steering rack. The contact stated that the dealer was selling vehicles with summer tires. There were no injuries. The current mileage was 8,800 and failure mileage was 8,780. Updated 01-30-08. *Kb the consumer stated failure warn about to summer rated tires. Updated 01/18/08 *tr

Filed Incident Steering · TiresNHTSA 10212489
Engine & cooling

Tl*the contact owns a 2007 mazda speed 3. While driving 40 mph, the motor mount broke when he shifted from first to second gear. As a result, the dry shaft pulled from the transmission and tore the cb axle boot. The contact installed an intake manifold prior to the failure. There is a safety recall for the engine and engine cooling (nhtsa campaign id #07v295000) however, the dealer refused to repair due to the installation of the intake manifold. The current and failure mileages were 11,700.

Filed Incident Engine and engine coolingNHTSA 10210923
Suspension

Rear wheel stabilizer bolt loose and damaged. Makes a "clunk" sound when going over small bumps. Bolt is loose and will come off. *Tr

Filed Incident SuspensionNHTSA 10210062
Engine & coolingTransmission & drivetrain

Motor mount failure. My transmission/motor mount failed causing the engine to fall in the engine bay. This has happened to several others as posted on http://www.Mazda3forums.Com/index.Php?Topic=68975.0. *Tr

Filed Incident Engine and engine cooling · Power trainNHTSA 10191833
Wheels & tires

I have a bridgestone potenza tire with 5k miles on it and it has a bulge in the sidewall.

Filed Incident TiresNHTSA 10191740
Engine & cooling

2007 Mazda aspeed 3 is prone to motor mount failure, I am taking the vehicle to the dealership to have them address loose motor mount, which according to recent data on the web , is prone to potentially catastrophic failure if the mount fails at highway speeds. *Ak

Filed Incident Engine and engine coolingNHTSA 10191205
Suspension

Heard rattle in rear of car. The passenger's side anti roll bar linkage was loose. The nut that secured the linkage was so loose that I was able to turn it with my finger. Dealer found the nut to be loose and torqued it to 40 feet-lb per the manual. *Ak

Filed Incident SuspensionNHTSA 10190852
Engine & coolingTransmission & drivetrain

Shifting from 1st to 2nd gear was rough sometimes. I checked the torque on bolt of driver's side engine mount and it was loose. It turned under 30 feet-lb. Bolt was supposed to be 70-80 feet-lb from the factory. After bolt was tightened to spec shifting became a lot smoother. I was convinced that if bolt was not tightened failure of driver' s-side engine mount bolt would have eventually resulted in a couple thousand more miles. Vehicle only had 3000 miles on it -engine would have dropped over left side driveshaft, causing loss of control of vehicle. Refer to investigation pe07015 . *Ak

Filed Incident Engine and engine cooling · Power trainNHTSA 10190851

Mazda MAZDASPEED3: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
20115200Body, doors & structureC
201032200Seats & seat beltsF
20090100-A
200833112Transmission & drivetrainF
200738210Transmission & drivetrainF
All MAZDASPEED3 years

2007 Mazda MAZDASPEED3 vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2007 Mazda MAZDASPEED3? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2007 Mazda MAZDASPEED3

Does the 2007 Mazda MAZDASPEED3 have any recalls?

Yes - NHTSA lists 2 recalls for the 2007 Mazda MAZDASPEED3: engine and engine cooling (July 2007); equipment (February 2007). Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2007 Mazda MAZDASPEED3?

By the complaints owners filed with NHTSA, the most common problem areas are the transmission & drivetrain (17), engine & cooling (15), wheels & tires (4).

How many complaints has the 2007 Mazda MAZDASPEED3 had?

38 complaints have been filed with NHTSA, the first on March 7, 2007 and the latest on August 4, 2016. Of these, 1 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.

Is the 2007 Mazda MAZDASPEED3 a reliable vehicle?

Its Safety Index is 12 out of 100 (grade F: far more problems than a typical Mazda MAZDASPEED3 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Mazda MAZDASPEED3 years have the most complaints?
What should I do if my 2007 Mazda MAZDASPEED3 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience