- The problem
- Insufficient material thickness in the rear suspension lower spring seats may allow the seat to flex and break the seat-to-axle weld.
- The fix
- Dealer will inspect and, if necessary, replace the lower spring seats, without charge to owner.
Vehicle safety record
1978 White Truck RB2 Problems, complaints & recalls
No owner complaints about the 1978 White Truck RB2 have been filed with NHTSA. It is covered by 10 recalls, the latest in August 1979 for the leaf spring assembly.
NHTSA data checked
FFar more problems than a typical RB2 year, for its age
- Complaints
- 0
- Recalls
- 10
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
1978 White Truck RB2 recalls 10
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Some of the involved vehicles were not inspected for adequate clearance between the steering shaft and its firewall opening. Inadequate clearance could result in the steering column becoming scored or severed by the firewall sheet metal.
- The fix
- Dealer will inspect vehicles and, if necessary, enlarge the firewall opening to provide the minimum 3/8 inch clearance for the steering shaft. Any scored or cut shafts will be replaced without charge to owner.
- The problem
- Lockwashers, used to retain the engine"s fan mounting bolts, may have been omitted during assembly, causing the bolts to loosen and allowing the fan to separate from its mounting hub.
- The fix
- DEALER WILL INSTALL LOCKWASHERS ON THE BOLTS.
- The problem
- The metal stiffener at the rear of the splash shield may become bent during servicing or by abuse. This can allow the splash shield and stiffener or one of its attaching bolts to rub against and cut the steering shaft.
- The fix
- The splash shield stiffener will be removed and the steering shaft will be replaced, if damaged.
- The problem
- The hose clamp, which was installed around the steering column boot seat to keep noise and dirt from entering the cab, may loosen.
- The fix
- Dealer will replace the metal hose clamp without charge.
- The problem
- The involved vehicles were built with certain tractor protection valves which may contain an extra valve. This may prevent the trailer brakes from fully releasing after a low pressure application, causing the trailer brakes to drag.
- The fix
- The dealer will inspect for the presence of the extra check valve. If found, the extra check valve will be removed. This will be done at no charge.
- The problem
- Some of the vehicles may have manganese bronze spring clip plates used as a substitute for malleable iron. The substitute clips, which are used to attach the suspension spring to the rear axle, may crack allowing the assembly to loosen. This can cause rear axle displacement.
- The fix
- The dealer will replace the manganese bronze clips with malleable iron clip plates at no cost to owner.
- The problem
- The windshield wiper may over-travel its designed sweep angle during its initial stroke with the possibility of temporary wiper immobilization.
- The fix
- Dealer will install a restriction fitting in the control valve at no cost to owner.
- The problem
- Loss of lights and engine shutdown may occur as a result of electrical system failure due to improper circuit crimping and potential heater motor circuit overloading. Also, the fuel solenoid may be improperly fused and the headlight harness improperly routed.
- The fix
- The dealer will make the necessary corrections, free of charge to the owner.
- The problem
- The involved vehicles may have been built with power unit anti-skid logic modules on tag axle installations instead of the correct trailer type modules. Since the tag axle sensor output is less than that of the power unit sensor, it requires the more sensitive trailer module. As sensor output over time drops below minimum requirements, one of two things will happen: (1) the anti-lock system on the tag axle will shut down and the cab mounted fault lamp will light or (2) the system will become inoperative without activating the fault light. This fails to conform to federal motor vehicle safety standard no. 121, "Air brakes".
- The fix
- Dealer will replace the incorrect anti-lock module without charge to owner.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
No complaints about the 1978 White Truck RB2 yet
White Truck RB2: every year compared
All RB2 yearsQuestions about the 1978 White Truck RB2
Does the 1978 White Truck RB2 have any recalls?
Yes - NHTSA lists 10 recalls for the 1978 White Truck RB2: leaf spring assembly (August 1979); steering wheel / handle bar (August 1979); fan (June 1979); steering wheel / handle bar (April 1979) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
How many complaints has the 1978 White Truck RB2 had?
None have been filed with NHTSA so far.
Is the 1978 White Truck RB2 a reliable vehicle?
Its Safety Index is 20 out of 100 (grade F: far more problems than a typical White Truck RB2 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
What should I do if my 1978 White Truck RB2 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data