Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Suspension

2000 Dodge Durango Suspension problems

Owners have filed 513 complaints about the 2000 Dodge Durango's suspension with NHTSA - 47% of all its complaints, most recently on December 21, 2021. They describe 18 crashes, 1 fire and 12 injuries. Broken springs, struts, control arms, ball joints, noises and alignment that won't hold.

Complaints
513
Recalls
2
Crashes
18
Fires
1
Injuries
12
Deaths
1

Suspension recalls for the 2000 Dodge Durango

Suspension: hub

08E0640002,805 vehicles affected

The problem
Skf is recalling 2,805 hub units, part no. Br930361, sold as a service part for 1997-2004 dodge dakota vehicles and 1999-2003 dodge durango vehicles equipped with 2-wheel drive & rear axle abs. Due to a specification error, the rotor pilot for the hub unit may be too long. This results in the wheel to not be seated fully against the hub flange face during mounting.
The risk
Improper seating of the wheel can result in excessive vibration, brake rotor noise, difficulty removing the wheel after installation and operation of the vehicle, and possibly wheel-end separation during vehicle operation. Should wheel-end separation occur, the driver could loose control of the vehicle, possibly resulting in a crash.
The fix
Skf will notify owners and replace the defective hub units free of charge. The recall began on november 5, 2008. Owners may contact skf vsm north america customer service at 1-800-644-8999.

Suspension: upper ball joint

04V596000592,707 vehicles affected

The problem
On certain sport utility vehicles and pickup trucks equipped with four-wheel drive (4x4), if moisture leaks into the front suspension upper ball joint, evacuation of the lubricant and corrosion of the joint may cause the joint to wear over an extended period of time. This could cause a clunking noise in the front suspension, which may not always be heard by the vehicle occupants.
The risk
Excessive wear in the upper ball joint may allow it to separate, which could result in loss of control of the vehicle.
The fix
Dealers will replace the front suspension upper ball joints. This safety improvement campaign began on december 21, 2004. Owners can contact daimlerchrysler at 1-800-853-1403.

Suspension complaints

SteeringSuspension

The contact owns a 2000 Dodge Durango. The contact stated while driving 5 MPH, she heard an abnormal noise coming from the front driver's side tire. The contact stated no warning light was illuminated. The contact exited the vehicle and stated that the front driver's side wheel was detached from the vehicle. The vehicle was not drivable. The contact towed the vehicle to an independent mechanic, and she was informed that the ball joint, tie rod, and wheel spindle needed to be replaced. Additionally, the vehicle...

Read the full complaint

would need a front wheel alignment. The vehicle was repaired. A dealer was not contacted. The manufacturer had not been informed of the failure. The failure mileage was approximately 240,000.

Filed Incident Steering · SuspensionNHTSA 11444532
Suspension

Tl* the contact owns a 2000 dodge durango. The contact received notification of nhtsa campaign number: 04v596000 (suspension) however, the part to do the recall repair was unavailable. The contact was also informed that the parts would not be available for thirty days. The vehicle was taken to rainier dodge of olympia (2550 carriage loop sw, olympia, wa 98502; (360) 754-5550) where it was confirmed that the part was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for...

Read the full complaint

the recall repair. The manufacturer was made aware of the issue. The contact stated that the wheel bearings and ball joints needed to be replaced. The contact stated that the vehicle made an abnormal sound. The approximate failure mileage was 140,000. Parts distribution disconnect.

Filed Incident SuspensionNHTSA 11373230
Suspension

There was a recall on the ball joints of the vehicle I own but I was told that the recall is closed. I believe that it should be covered for repair because I wasn't made aware of any recalls when I obtained the vehicle. The upper ball joints are bad and a mechanic told me it could break off.

Filed Incident SuspensionNHTSA 11217475
SuspensionEngine & coolingFire

Tl* the contact owns a 2000 dodge durango. While driving 45 mph, the front driver side of the vehicle lowered to the ground and smoke began to emit from the vehicle. In addition, the front upper and lower ball joints bent inward and needed to be replaced. On two separate occasions, the radiator failed to operate and caused the cooling system to fail. The vehicle was taken to an independent mechanic where the wheel hub bearing, front upper and lower ball joints, and cold air intake system were replaced. The...

Read the full complaint

manufacturer was notified of the failures and stated that the vin was not included in nhtsa campaign numbers: 04v596000 (suspension), 06e024000 (engine and engine cooling) or 08e064000 (suspension). The failure mileage was 125,000.

Filed Incident Suspension · Engine and engine coolingNHTSA 10968884
Suspension

I purchased a 2000 dodge durango in june 2003. I have had continuing problems with front suspension, ball joints,right hub assembly. Right side hub assembly has been replaced 5 times in the last 6 years and I was just told yesterday that it will need to be replaced again. I was also informed by my mechanic of 18 years, the whole front suspension is bad and the differential will also have to be replaced. I have owned this truck 11 years and have kept it well maintained,in all this time, I have had only one official...

Read the full complaint

recall for upper arm ball joints in 2005. I have called chrysler twice to question why I have had to replace the hub assembly so frequently(every year for the last 5 of 6 years) and they insist there is nothing wrong or a specific recall for my vin. I have had enough with replacing the same part over and over every year. Something needs to be done about this hub assembly & front suspension. I have noticed the same complaints online as mine.... Front end vibration when reaching speeds of 55-60 mph, ball joint issues, hub assembly issues, and front suspension issues. There are currently 2 recalls for 2000 dodge durango front suspension and hub assembly units, and conveniently for chrysler, neither are my vin number durango. Surprise, surprise!! I will continue to file complaints with chrysler until some one decides to take action and get these issues repaired once and for all. I am getting a little tired of constantly putting out hundreds of dollars for the same issue year after year!! Please help get this issue resolved! *Tr

Filed Incident SuspensionNHTSA 10562280
Suspension

Tl* the contact owns a 2000 dodge durango. The contact stated that the vehicle would vibrate while driving approximately 60 mph. The contact also stated that the inner and outer edges of the tires were wearing unevenly. The vehicle was not taken to have the failure diagnosed or repaired. The manufacturer was made aware of the failure and informed the contact that the vehicle was not included in the recall associated with nhtsa campaign id number 04v596000 (suspension:front:control arm:upper ball joint). The failure mileage was 120,000.

Filed Incident SuspensionNHTSA 10438550
Suspension

Tl* the contact owns a 2000 dodge durango. The contact stated that while driving 60 mph, the hub unit fractured in half. The manufacturer was contacted and advised the contact that the vin was not included in the recall associated with nhtsa campaign id number: 08e064000 (suspension:front:hub). The dealer denied any assistance with repaired to the vehicle. The vehicle was not repaired. The failure and current mileage was 185,000.

Filed Incident SuspensionNHTSA 10429411
SteeringSuspension

I was pulling out of my circular driveway steering left and the wheel base wouldn't turn. So I backed up and continue to go around the curve, once I reached about 200 ft off my driveway, my car come to a complete stop on it's own. I backed into my driveway dragging my passenger side front wheel sideways. Once I got out to check what was going on, my tie rod end had become completely stripped off the rack and pinion. After further inspections, somehow the groves on the rack and pinion had wore down so much it...

Read the full complaint

allowed the tie rod to strip and release. I was so glad I hadn't been driving with my children on the highway, this would have caused my vehicle to flip and probably kill us. I know have to replace my rack and pinion and tie rod and just replacing the ball joints on this vehicle not a couple months ago. I am very frightened to drive it now in fear this will happen again.

Filed Incident Steering · SuspensionNHTSA 10403335
Suspension

Vehicles has been making front noise of axel is about to come off - sometime in the summer I had the bearing replaced as they had cracked then the noise in front of vehicle suspension started again. I think that this may be a recall problem. *Tr

Filed Incident SuspensionNHTSA 10296994
Suspension

Front left bushing repaired 6 times and still squeaks at every suspension compression. *Tr

Filed Incident SuspensionNHTSA 10267759
Suspension

2/18/2009 Mechanic fixed wheel bearing-front suspension hub and bearing left side 1 yr ago same thing was done to right side. I paid out of pocket both times. He told me to check into recall on dodge durango. *Tr

Filed Incident SuspensionNHTSA 10259499
Suspension

Tl*the contact owns a 2000 dodge durango. While driving various speeds over hills or bumps, the vehicle would vibrate abnormally. The vehicle was taken to a repair shop and the technician stated that it was unsafe to drive because the ball joints were severely corroded. The contact called an authorized dealer in reference to nhtsa campaign id number 04v596000 (suspension:front:control arm:upper ball joint) and was informed that his vin was not included in the recall. The contact would be responsible for the repair costs. The vehicle has not been repaired. The failure and current mileages were 90,000.

Filed Incident SuspensionNHTSA 10243289
Suspension

Tl*the contact owns a 2000 dodge durango. The contact heard a clunking noise in the front suspension while driving 5 mph. She called the dealer in reference to nhtsa campaign id number 04v596000 (suspension:front:control arm:upper ball joint). The technician stated that because her vehicle was 2 wheel drive, her vin was excluded from the recall. The contact would be responsible for the recall repair. She is in the process of having the vehicle repaired. The manufacturer was unable to assist. The failure and current mileages were 120,882.

Filed Incident SuspensionNHTSA 10240991
Suspension

Tl*the contact owns a 2000 dodge durango. In august of 2007, the contact heard an unfamiliar noise coming from the front passenger side of the vehicle. She noticed that the front passenger side tire was wearing faster than normal and had to be replaced twice. Between september of 2007 and august of 2008, the noise intensified. The dealer stated that the front passenger side ball joint was the cause of the failure. The manufacturer stated that her vin was not included in nhtsa campaign id number 04v596000 (suspension:front:control arm:upper ball joint). The failure mileage was 100,000 and current mileage was 118,000.

Filed Incident SuspensionNHTSA 10240650
SteeringSuspensionWheels & tires

I was told that the upper and lower ball joints needed to be replaced. I have owned many vehicles and never have had so many front end issues on one vehicle than this one. I was wondering if there has been any recalls on the 2 wheel drive dodge durango, rear wheel drive. 5.2L engine this vehicle did have a recall issued on the rack and pinion steering. *Tr

Filed Incident Steering · Suspension · WheelsNHTSA 10238471
Suspension

Regular driving. Noise from rear end. Dealership replaced rear carrier and all bearings/races. *Tr

Filed Incident SuspensionNHTSA 10205145
SuspensionEquipment & accessories

2000 Dodge durango, when my car had 70,000 miles on it, there was a recall of the ball joints. My durango now has 100,000+ miles and it is making the same popping noise in the front end. My mechanic says that it needs new ball joints again. I feel dodge replaced the ball joints with the same defective parts as the original parts. This is a safety issue. When I contacted dodge I was told via e-mail that warranty was only until 10 years or 100,000 miles. They did not count on owners keeping this vehicle. This is a safety issue that I feel dodge should stand behind. *Jb

Filed Incident Suspension · EquipmentNHTSA 10204617
Suspension

Tl*the contact owns a 2000 dodge durango. The contact received recall notice number 04v596000 (suspension:front:control arm:upper ball joint). He took the vehicle to a local mechanic and they notified fresno dodge. The dealer refused to perform the recall repair because the vehicle was not experiencing any failures at the time. The dealer also informed the contact that even though he received a recall notice, he would still be responsible for the repair costs. There have been no failures to date. The current...

Read the full complaint

mileage was 113,000 and failure mileage was 75,000. The consumer stated does not understand why the dealer would not perform the recall and would not cover the cost of the recall. The consumer stated would like to be reimbursed for recall performed on the vehicle. The consumer provided the recall issued and the repair invoice. Updated 09/10/07 *tr

Filed Incident SuspensionNHTSA 10197805
Suspension

Tl*the contact owns a 2000 dodge durango. While driving 35 mph the vehicle pulled to the right. She stated that the vehicle has had several wheel alignments. She received a recall notice (recall#04v596000) for the front upper ball joints. The dealer inspected the vehicle and stated that the upper ball joints did not need to be replaced; however the problem continued to occur. The current mileage was 142,000 and the failure mileage was 99,200. Updated 01/07/08.*Lj updated 12/12/07

Filed Incident SuspensionNHTSA 10197327
Suspension

FRONT BALL JOINTS FAILED. *AK

Filed Incident SuspensionNHTSA 10190509
Suspension

FRONT UPPER BALL JOINTS. *AK

Filed Incident SuspensionNHTSA 10190508
Suspension

Make: dodge model: durango year: 2000, I always had problems with the durango since about 13,000, (now have 93,000. Replacement of ball joints, brake calipers, and continuous checks for clicking and vibration feeling in the steering column. This has not been right from the start. I believe there is something defective with the steering and front end. Each time I take it to the dealer for service they can never duplicate the problem. I have enjoyed the durango, except for these front end problems. The steering makes noises and has a funny response to the turning process. Could you please review closer. *Ak

Filed Incident SuspensionNHTSA 10188240
SteeringSuspension

Tl*the contact owns a 2000 dodge durango. The vehicle was brought to the dealer to perform recall 04v596000 repairs. Immediately after the vehicle was repaired the steering assembly shifted and the contact was unable to drive the vehicle forward. The vehicle was involved in collisions prior to it being purchased by the contact, w3hich may have contributed to the failure. The dealer did not correct the failure, and the vehicle has not been driven for a year. The vehicle was towed from the dealer to a relative's home. The contact had not experienced any failures with the vehicle prior to the recall repair. The current and failure mileage were 80,000.*Ak

Filed Incident Steering · SuspensionNHTSA 10187934
SteeringSuspensionVisibility & wipers

I bought my truck used and had them do a complete work up on it when I purchased it. Everything was fine for 1 week. After that week my engine light came on. I took it back to the dealer and had them replace the "canister" because that's what they said was the problem. 1 Week later it returned. I have had it cleared out about 100 times. It now keeps telling me I have a gas leak. My mechanic has looked at this truck more than the average time. Now I am at 130,000 miles and my suspension is completely shot, power steering pump, automatic locks are slowly malfunctioning (they make a loud noise on 2 of the doors), and the drivers side window doesn't roll down. *Jb

Filed Incident Steering · Suspension · VisibilityNHTSA 10183277
Suspension

Tl* - the contact called regarding a 2000 dodge durango. The contact stated that the right front wheel came off the vehicle. While traveling at 25 mph. The road conditions were dry. The failure mileage was 73,000. There were no injuries. The tire on the vehicle rolled out into the highway and struck another vehicle causing damage to that vehicle. A police report filed. The vehicle was towed to a chrysler dodge dealer, who was unable to diagnose the problem. Also, there was also minor damage to the front bumper .

Filed Incident SuspensionNHTSA 10182112

Dodge Durango suspension complaints by year

Durango suspension problems, every year

Had a suspension problem with your 2000 Durango? Tell other owners.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience