Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2009 Kenworth T2000 Problems, complaints & recalls

No owner complaints about the 2009 Kenworth T2000 have been filed with NHTSA. It is covered by 12 recalls, the latest in March 2011 for the engine and engine cooling.

NHTSA data checked

DMore problems than a typical T2000 year, for its age

Complaints
0
Recalls
12
Crashes
0
Fires
0
Injuries
0
Deaths
0

2009 Kenworth T2000 recalls 12

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Engine and engine cooling

11V2030005,831 vehicles affected

The problem
Paccar is recalling certain model year 2007-2011 kenworth c500, t2000, t600, and t660, as well as model year 2009-2011 peterbilt 387 and 388 trucks equipped with caterpillar c15 engine and manufactured from may 11, 2006, through september 17, 2010. Degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on c15 engines.
The risk
THIS COULD RESULT IN A FIRE.
The fix
Caterpillar is handling the owner notification and remedy for this campaign. Please see caterpillar's defect report 11e-006. Caterpillar will replace the single piece combustion tube with a thick wall combustion tube which will not allow the heat to break through. This service will be performed free of charge. Due to a parts supply issue, owners will be notified by the end of april 2011 about the safety defect, and will then be notified again once the free remedy is available, currently estimated to be around late july 2011. Owners may contact caterpillar toll-free at 1-800-447-4986.

Fuel system: tank assembly

11V1270004,664 vehicles affected

The problem
Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
The risk
The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
The fix
Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Steering: column

10V3080009,697 vehicles affected

The problem
Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
The risk
A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
The fix
Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

Power train: axle assembly

09V415000914 vehicles affected

The problem
Kenworth is recalling model year 2009 through 2010 t2000, t800, t660 and w900 trucks manufactured between november 12, 2008 and september 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain ag400l rear suspensions may have received insufficient fastener torque during the installation process. The insufficient torque may allow the axle u-bolt to become loose, which may cause vibration in the rear suspension.
The risk
If multiple fasteners were to become loose, the rear axle may shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.
The fix
Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on november 4, 2009. Owners may contact kenworth at 425-828-5440.

Steering: column

09V2580002,096 vehicles affected

The problem
Paccar is recalling 2,096 my 2009 kenworth and peterbilt vehicles equipped with trw steering shafts. Mislocation of a circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
The risk
A separation of the splined and non-splined tubes could cause a loss of steering control and increase the risk of a crash.
The fix
Dealers will inspect the steering shaft using a weld placement gauge and miswelded steering shaft will be replaced free of charge. The recall began july 31, 2009. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Service brakes

09V2390003,423 vehicles affected

The problem
Kenworth is recalling 3,423 my 2004-2009 t2000, t800,t600, w900 and t660 vehicles. Increased brake excitation in a certain vehicle configuration which includes bendix drum brakes, wide base low profile single tires, and an ag400 or ag460 rear suspension, due to its unique brake clocking and cam tube length, can cause fatigue and cracking to brake assembly components.
The risk
Cracking can cause a complete fracture of the cam tube, which could increase stopping distance and decrease parking brake hold capability.
The fix
Dealers will inspect the rear axle brakes assembly, replace cracked rear axle brakes assembly components where required, and install cam tube support brackets on all rear axle wheel ends free of charge. The recall is expected to begin or before july 25, 2009. Owner may contact kenworth at 1-425-828-5440.

Service brakes: hoses, lines / piping, and fittings

09V22700013 vehicles affected

The problem
Kenworth is recalling 13 my 2009 t2000 vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 106, "Brake hoses." Air tube expander fitting used between the air tube inlet and dash air gauges for the trailer does not meet the burst pressure requirements.
The risk
This can result in brake hose rupture, air pressure loss, and compromised vehicle braking which could result in a crash without warning.
The fix
Dealers will inspect and replace the expander fitting which is related to 1,200 psi. This service will be performed free of charge. The safety recall began on june 3, 2009. Owners may contact kenworth at 1-425-828-5440.

Engine and engine cooling: diesel

09V0190001,098 vehicles affected

The problem
Paccar is recalling 1098 kenworth my 2008 t800, w900, my 2008-2009 t2000 and peterbilt my 2007-2009 379 and 387 trucks equipped with c15 caterpillar diesel engines. The aftertreatment regeneration device (ard) may develop a hole and heat and flame may escape during a regeneration of the diesel particulate filter.
The risk
THIS MAY RESULT IN A FIRE HAZARD.
The fix
Paccar is working with caterpillar and will inspect and remedy the engines free of charge. Owners may contact caterpillar at 1-800-447-4986, kenworth at 425-828-5440 or peterbilt at 940-591-4196.

Suspension

08V485000130 vehicles affected

The problem
Paccar is recalling 130 my 2004-2009 t2000, t800, t600, w900 and t660 kenworth trucks built with an ag400 rear suspension, long stroke brake chambers, and wide base tires (super singles). These vehicles may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly (brake cam tube support, brake chamber bracket, brake chamber, brake spider) to develop fatigue cracks, possibly resulting in the failure of the part or parts within the brake assembly.
The risk
A failure may reduce vehicle brake performance, increasing the risk of a crash.
The fix
Dealers will install the cam tube support brackets on all of the rear axle wheel ends. Inspect the rear axle brake assembly and replace it if cracked. The recall is expected to begin during november 2008. Owners may contact kenworth at 1-425-828-5440.

Engine and engine cooling: diesel

08V4870004,883 vehicles affected

The problem
Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.
The risk
A vehicle crash could occur if another vehicle strikes the dpf on the roadway.
The fix
Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Suspension

08V3140001,189 vehicles affected

The problem
Kenworth is recalling 1,189 my 2009 t2000, t600, t660, t800 and w900 trucks. The axle u-bolts attaching the axle to the drive beam on certain ag380 rear suspensions may have received insufficient fastener torque during the installation process.
The risk
The insufficient torque may allow the axle u-bolt to loosen if undetected, could impact long term suspension performance and increase the risk of a crash.
The fix
Dealers will have the axle u-bolt on the affected chassis re-torqued to factory specifications free of charge. The recall began on august 12, 2008. Owners may contact kenworth at 425-828-5440.

Parking brake: air

08V1280001,043 vehicles affected

The problem
Paccar is recalling 1,043 my 2008-2009 kenworth c500, t2000,t660, t800 and w900 trucks equipped with bendix mv-3 dash control valves. The molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double check valve area. This condition can allow the rubber double check valve to become lodged in the body opening under certain circumstances.
The risk
If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged double check valve thereby depleting the secondary reservoir, Causing reduced ability for modulating the service emergency brakes. In such an event, the operator should observe an air leak, indications of low air pressure via the primary and secondary air gauges, and audible and visual low air pressure warning alarms. A vehicle crash is possible if these warnings are not heeded.
The fix
Dealers will replace the bendix mv-3 dash control valves free of charge. The recall began on april 14, 2008. Owners may contact kenworth at 1-425-828-4196.

What owners say

Be the first T2000 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

No complaints about the 2009 Kenworth T2000 yet

No owner has filed a complaint about this vehicle with NHTSA. If yours has a problem, share it here and report it to NHTSA.

Kenworth T2000: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
20120100-A
20110200-A
20100600-C
200901200-D
200821400Engine & coolingF
2007121100BrakesF
20067700BrakesD
20050700-C
All T2000 years

2009 Kenworth T2000 vs rivals

VehicleComplaintsRecallsCrashesGrade
2009 Kenworth T20000120D
2009 Kenworth T8002191DCompare

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2009 Kenworth T2000? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2009 Kenworth T2000

Does the 2009 Kenworth T2000 have any recalls?

Yes - NHTSA lists 12 recalls for the 2009 Kenworth T2000: engine and engine cooling (March 2011); tank assembly (February 2011); column (July 2010); axle assembly (October 2009) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

How many complaints has the 2009 Kenworth T2000 had?

None have been filed with NHTSA so far.

Is the 2009 Kenworth T2000 a reliable vehicle?

Its Safety Index is 25 out of 100 (grade D: more problems than a typical Kenworth T2000 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Kenworth T2000 years have the most complaints?
What should I do if my 2009 Kenworth T2000 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience