Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2008 Kenworth T2000 Problems, complaints & recalls

Owners have filed 2 complaints about the 2008 Kenworth T2000 with NHTSA, most often about the engine & cooling (2) and the equipment & accessories (1). It is covered by 14 recalls, the latest in March 2011 for the engine and engine cooling. For comparison, the 2007 has 12 and the 2009 has 0.

NHTSA data checked

FFar more problems than a typical T2000 year, for its age

#370 most complained-about 2008 vehicle

Complaints
2
Recalls
14
Crashes
0
Fires
0
Injuries
0
Deaths
0

Most common 2008 Kenworth T2000 problems

Share of all 2 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2008 Kenworth T2000 recalls 14

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Engine and engine cooling

11V2030005,831 vehicles affected

The problem
Paccar is recalling certain model year 2007-2011 kenworth c500, t2000, t600, and t660, as well as model year 2009-2011 peterbilt 387 and 388 trucks equipped with caterpillar c15 engine and manufactured from may 11, 2006, through september 17, 2010. Degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on c15 engines.
The risk
THIS COULD RESULT IN A FIRE.
The fix
Caterpillar is handling the owner notification and remedy for this campaign. Please see caterpillar's defect report 11e-006. Caterpillar will replace the single piece combustion tube with a thick wall combustion tube which will not allow the heat to break through. This service will be performed free of charge. Due to a parts supply issue, owners will be notified by the end of april 2011 about the safety defect, and will then be notified again once the free remedy is available, currently estimated to be around late july 2011. Owners may contact caterpillar toll-free at 1-800-447-4986.

Fuel system: tank assembly

11V1270004,664 vehicles affected

The problem
Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
The risk
The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
The fix
Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Power train: axle assembly

10V63400012,873 vehicles affected

The problem
Paccar is recalling certain model year 2007-2008 kenworth and peterbilt vehicles manufactured from february 2, 2006 through april 30, 2007. The bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of lubrication and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. This condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle.
The risk
Detachment of the driveline from the axle may cause the vehicle to lose power and become disabled in the roadway. Also, the driveline could drop from the vehicle into the roadway increasing the risk of a crash.
The fix
Paccar is working with its supplier to remedy the vehicles free of charge. The safety recall is expected to begin during february 2011. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

Steering: column

10V3080009,697 vehicles affected

The problem
Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
The risk
A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
The fix
Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

Service brakes

09V2390003,423 vehicles affected

The problem
Kenworth is recalling 3,423 my 2004-2009 t2000, t800,t600, w900 and t660 vehicles. Increased brake excitation in a certain vehicle configuration which includes bendix drum brakes, wide base low profile single tires, and an ag400 or ag460 rear suspension, due to its unique brake clocking and cam tube length, can cause fatigue and cracking to brake assembly components.
The risk
Cracking can cause a complete fracture of the cam tube, which could increase stopping distance and decrease parking brake hold capability.
The fix
Dealers will inspect the rear axle brakes assembly, replace cracked rear axle brakes assembly components where required, and install cam tube support brackets on all rear axle wheel ends free of charge. The recall is expected to begin or before july 25, 2009. Owner may contact kenworth at 1-425-828-5440.

Engine and engine cooling: diesel

09V0190001,098 vehicles affected

The problem
Paccar is recalling 1098 kenworth my 2008 t800, w900, my 2008-2009 t2000 and peterbilt my 2007-2009 379 and 387 trucks equipped with c15 caterpillar diesel engines. The aftertreatment regeneration device (ard) may develop a hole and heat and flame may escape during a regeneration of the diesel particulate filter.
The risk
THIS MAY RESULT IN A FIRE HAZARD.
The fix
Paccar is working with caterpillar and will inspect and remedy the engines free of charge. Owners may contact caterpillar at 1-800-447-4986, kenworth at 425-828-5440 or peterbilt at 940-591-4196.

Suspension

08V485000130 vehicles affected

The problem
Paccar is recalling 130 my 2004-2009 t2000, t800, t600, w900 and t660 kenworth trucks built with an ag400 rear suspension, long stroke brake chambers, and wide base tires (super singles). These vehicles may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly (brake cam tube support, brake chamber bracket, brake chamber, brake spider) to develop fatigue cracks, possibly resulting in the failure of the part or parts within the brake assembly.
The risk
A failure may reduce vehicle brake performance, increasing the risk of a crash.
The fix
Dealers will install the cam tube support brackets on all of the rear axle wheel ends. Inspect the rear axle brake assembly and replace it if cracked. The recall is expected to begin during november 2008. Owners may contact kenworth at 1-425-828-5440.

Engine and engine cooling: diesel

08V4870004,883 vehicles affected

The problem
Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.
The risk
A vehicle crash could occur if another vehicle strikes the dpf on the roadway.
The fix
Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Parking brake: air

08V1280001,043 vehicles affected

The problem
Paccar is recalling 1,043 my 2008-2009 kenworth c500, t2000,t660, t800 and w900 trucks equipped with bendix mv-3 dash control valves. The molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double check valve area. This condition can allow the rubber double check valve to become lodged in the body opening under certain circumstances.
The risk
If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged double check valve thereby depleting the secondary reservoir, Causing reduced ability for modulating the service emergency brakes. In such an event, the operator should observe an air leak, indications of low air pressure via the primary and secondary air gauges, and audible and visual low air pressure warning alarms. A vehicle crash is possible if these warnings are not heeded.
The fix
Dealers will replace the bendix mv-3 dash control valves free of charge. The recall began on april 14, 2008. Owners may contact kenworth at 1-425-828-4196.

Latch

08V0650006,169 vehicles affected

The problem
Paccar is recalling 6,169 my 2008 kenworth t300, t660, t800, t2000, w900 and c500 vehicles and my 2008-2009 peterbilt models 365, 367, 384, 387, 388, 389 and 389 kits. Certain door latch assemblies on these vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 206, 'Door locks and door retention components." The rotor in some of these door latch assemblies did not receive the proper heat treatment and may be soft.
The risk
In the event of a crash, force could cause the rotor to crack and the door would not have primary or secondary closing security which could possibly lead to injury of the vehicle occupant.
The fix
Paccar is working with trimark and will inspect and replace the door latch if it is found to be defective. The recall began on march 14, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Service brakes: hoses, lines / piping, and fittings

08V0020002,794 vehicles affected

The problem
Certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 106, "Brake hoses." The tubing was manufactured with only four layers of nylon material, instead of the specified five layers.
The risk
The diameter of the hose affects the fittings which may allow air to leak from the brakes and create the potential for a vehicle crash.
The fix
Dealers will inspect the air brake hoses and, if necessary, replace the hoses. The recall began on february 22, 2008. Owner notification schedule for this campaign. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Steering: shaft sector

07V591000559 vehicles affected

The problem
On certain kenworth and peterbilt heavy duty trucks equipped with tas-85 trw steering gears, the inner surface of the outer sector shaft teeth of the steering gears may have an incorrect involute profile, which may lead to chipping and damage of the gearing system.
The risk
This type of damage may cause a "bind/stick" condition in the vehicle steering during a turn increasing the risk of a crash.
The fix
Dealers will repair and replace any suspect tas-85 steering gear assembly free of charge. The recall began on january 9, 2008. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4201.

Trailer hitches

07V2690009,571 vehicles affected

The problem
On certain trucks, the removable tow hitch ,when used to tow or lift a vehicle, can fail due to defective material in the tow hitch.
The risk
If the tow hitch assembly fails while a vehicle is being towed or lifted, it may cause an accident that could result in personal injury or death.
The fix
Dealers will replace the tow pin assembly free of charge. The recall began on september 4, 2007. Owners may contact kenworth at 425-828-5440 or peterbilt at 940-591-4201.

Vehicle speed control: cruise control

06V446000116 vehicles affected

The problem
An incorrect switch was installed in the cruise control system on certain model t300 trucks.
The risk
A light application of the brakes will not deactivate the cruise control and the system will have to be shut off by the dash switch. This could lead to unintended acceleration and a crash without warning.
The fix
Kenworth will install the correct sensor switch. The recall began on january 10, 2007. Owners may contact kenworth at 1-425-828-5440.

What owners say

Be the first T2000 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

2 complaints about the 2008 Kenworth T2000

Newest first, as filed with NHTSA by owners.

Engine & cooling

Tl* the contact owns a 2008 kenworth t2000. The contact stated that the fuel burning chamber malfunctioned and caused the check engine light to continuously illuminate. The vehicle was taken to the dealer who stated that the exhaust temperature sensor needed to be replaced. The vehicle was repaired; however, the failure continued to occur. The manufacturer was notified of the defect. The approximate failure mileage was 674,692. Updated 06/17/14 ma updated 8/21/17*cn

Filed Incident EngineNHTSA 10579518
SuspensionEngine & coolingWheels & tiresEquipment & accessories

Fox transportation, its employees, agents, successors or those acting in concert, commit negligence, intentional negligence, theft and failure to pay employers for work done and or moneys owed on more than one occasion of settlement(s), while protecting those who commit said action(s) and theft(s) acting in concert with. The company fabricates lease documents to violate business and profession codes in ownerships of parties and contracts, breach of contract and theft of employees personal property owned in the...

Read the full complaint

leased equipment hindering of life. Fox practices racial discrimination with loads and in work environment and hiring process, using loads to perpetrate and control leasers success of finance and any ownership or possible final ownership, committing frauds. Fox leases equipment through employees untrained or not experienced to adequately facilitate good business, creating poor safety issues and dangerous work conditions, increasing poor work relations and also leasing equipment that is unsafe for the road, needing repairs to be operable and safe for the road, and shifting the responsibility on leaser(s) after thirty (30) days, and possibly hiring illegals in conflict with e-file and immigration laws, while they trump up fees and charges fabricated and force its owner operators out of business breaching contracts entered, and they fail to reimburse owner operator for fuel left in substituted trucks or repairs made to leased trucks for safe operation violating policy and state and federal laws. *Tr

Filed Incident Suspension · Engine and engine cooling · Tires · EquipmentNHTSA 10575759

Kenworth T2000: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
20120100-A
20110200-A
20100600-C
200901200-D
200821400Engine & coolingF
2007121100BrakesF
20067700BrakesD
20050700-C
20043700Driver assistanceD
All T2000 years

2008 Kenworth T2000 vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2008 Kenworth T2000? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2008 Kenworth T2000

Does the 2008 Kenworth T2000 have any recalls?

Yes - NHTSA lists 14 recalls for the 2008 Kenworth T2000: engine and engine cooling (March 2011); tank assembly (February 2011); axle assembly (December 2010); column (July 2010) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2008 Kenworth T2000?

By the complaints owners filed with NHTSA, the most common problem areas are the engine & cooling (2), equipment & accessories (1), suspension (1).

How many complaints has the 2008 Kenworth T2000 had?

2 complaints have been filed with NHTSA, the first on March 31, 2014 and the latest on April 14, 2014. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.

Is the 2008 Kenworth T2000 a reliable vehicle?

Its Safety Index is 20 out of 100 (grade F: far more problems than a typical Kenworth T2000 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Kenworth T2000 years have the most complaints?
What should I do if my 2008 Kenworth T2000 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience