- The problem
- Paccar is recalling certain model year 2007-2011 kenworth c500, t2000, t600, and t660, as well as model year 2009-2011 peterbilt 387 and 388 trucks equipped with caterpillar c15 engine and manufactured from may 11, 2006, through september 17, 2010. Degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on c15 engines.
- The risk
- THIS COULD RESULT IN A FIRE.
- The fix
- Caterpillar is handling the owner notification and remedy for this campaign. Please see caterpillar's defect report 11e-006. Caterpillar will replace the single piece combustion tube with a thick wall combustion tube which will not allow the heat to break through. This service will be performed free of charge. Due to a parts supply issue, owners will be notified by the end of april 2011 about the safety defect, and will then be notified again once the free remedy is available, currently estimated to be around late july 2011. Owners may contact caterpillar toll-free at 1-800-447-4986.
Vehicle safety record
2010 Kenworth T2000 Problems, complaints & recalls
No owner complaints about the 2010 Kenworth T2000 have been filed with NHTSA. It is covered by 6 recalls, the latest in March 2011 for the engine and engine cooling.
NHTSA data checked
CAbout as many problems as a typical T2000 year, for its age
- Complaints
- 0
- Recalls
- 6
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
2010 Kenworth T2000 recalls 6
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
- The risk
- The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
- The fix
- Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.
- The problem
- Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
- The risk
- A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
- The fix
- Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.
- The problem
- Kenworth is recalling certain model year 2010 t2000, t660, t800 and w900 vehicles manufactured between july 30, 2009 and september 18, 2009. The rear axle outer end hub may have not been primed with oil properly during the rear axle installation process. Potential lack of oil may cause the outer end bearing to heat up and/or seize, possibly resulting in the overheating of the wheel end.
- The risk
- A wheel end fire may occur, increasing the risk of a crash.
- The fix
- Dealers will replace the bearings, seals and will add oil to the outer end hub as well as inspect races and axle housing for damage and replacing as necessary free of charge. The safety recall began on may 24, 2010. Owners may contact kenworth at 425-828-5440.
- The problem
- Kenworth is recalling model year 2010 t2000, t800, t660 and w900s trucks manufactured between july 1 and october 23, 2009. The fasteners attaching the steering gear to the front drive bracket may have received insufficient torque during the installation process resulting in less than required clamp load.
- The risk
- The insufficient clamp load may allow the fastener(s) to become loose and fall away from the vehicle resulting in road debris. If multiple fasteners were to become loose, the vehicle steering may wander, which could result in a crash.
- The fix
- Dealers will inspect and re-torque the steering gear mounting bolts free of charge. The safety recall is expected to begin during january 2010. Owners may contact kenworth at 1-425-828-5440.
- The problem
- Kenworth is recalling model year 2009 through 2010 t2000, t800, t660 and w900 trucks manufactured between november 12, 2008 and september 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain ag400l rear suspensions may have received insufficient fastener torque during the installation process. The insufficient torque may allow the axle u-bolt to become loose, which may cause vibration in the rear suspension.
- The risk
- If multiple fasteners were to become loose, the rear axle may shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.
- The fix
- Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on november 4, 2009. Owners may contact kenworth at 425-828-5440.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
No complaints about the 2010 Kenworth T2000 yet
Kenworth T2000: every year compared
All T2000 years2010 Kenworth T2000 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2010 Kenworth T2000 | 0 | 6 | C | |
| 2010 Kenworth T660 | 2 | 10 | D | Compare |
| 2010 Kenworth C500 | 1 | 4 | D | Compare |
| 2010 Kenworth T800 | 1 | 11 | C | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2010 Kenworth T2000
Does the 2010 Kenworth T2000 have any recalls?
Yes - NHTSA lists 6 recalls for the 2010 Kenworth T2000: engine and engine cooling (March 2011); tank assembly (February 2011); column (July 2010); spindle (May 2010) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
How many complaints has the 2010 Kenworth T2000 had?
None have been filed with NHTSA so far.
Is the 2010 Kenworth T2000 a reliable vehicle?
Its Safety Index is 49 out of 100 (grade C: about as many problems as a typical Kenworth T2000 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T2000 years have the most complaints?
2007 (12), 2006 (7), 1997 (3). See every Kenworth T2000 year compared.
What should I do if my 2010 Kenworth T2000 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data