Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2010 Kenworth T660 Problems, complaints & recalls

Owners have filed 2 complaints about the 2010 Kenworth T660 with NHTSA, most often about the brakes (1) and the steering (1). Those complaints describe 1 crash and 1 injury. It is covered by 10 recalls, the latest in February 2024 for the reservoir / tank. For comparison, the 2009 has 0 and the 2011 has 1.

NHTSA data checked

DMore problems than a typical T660 year, for its age

#327 most complained-about 2010 vehicle

Complaints
2
Recalls
10
Crashes
1
Fires
0
Injuries
1
Deaths
0

Most common 2010 Kenworth T660 problems

Share of all 2 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2010 Kenworth T660 recalls 10

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Service brakes: reservoir / tank

24V145000936 vehicles affected

The problem
PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
The risk
Insufficient air volume can reduce braking performance and increase the risk of a crash.
The fix
Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.

Electronic stability control (ESC)

20V199000460,515 vehicles affected

The problem
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
The risk
If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
The fix
PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

Engine and engine cooling

11V2030005,831 vehicles affected

The problem
Paccar is recalling certain model year 2007-2011 kenworth c500, t2000, t600, and t660, as well as model year 2009-2011 peterbilt 387 and 388 trucks equipped with caterpillar c15 engine and manufactured from may 11, 2006, through september 17, 2010. Degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on c15 engines.
The risk
THIS COULD RESULT IN A FIRE.
The fix
Caterpillar is handling the owner notification and remedy for this campaign. Please see caterpillar's defect report 11e-006. Caterpillar will replace the single piece combustion tube with a thick wall combustion tube which will not allow the heat to break through. This service will be performed free of charge. Due to a parts supply issue, owners will be notified by the end of april 2011 about the safety defect, and will then be notified again once the free remedy is available, currently estimated to be around late july 2011. Owners may contact caterpillar toll-free at 1-800-447-4986.

Fuel system: tank assembly

11V1270004,664 vehicles affected

The problem
Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
The risk
The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
The fix
Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Service brakes: caliper

10V535000417 vehicles affected

The problem
Paccar is recalling certain model year kenworth t660, t700, t800 and w900 vehicles manufactured from december 22, 2008, through august 2, 2010, and equipped with ag400l air disc brakes. The air disc brake caliper could be installed on the wrong side of the drive axle potentially causing interference with the suspension bracket and the rear suspension as the outermost brake pads wear and the floating caliper moves inboard.
The risk
As this interference gets larger, this could eventually lead to reduced braking performance, increasing the risk of a crash.
The fix
Dealers will verify the correct orientation of the brake caliper and perform the necessary repair free of charge. The safety recall began on november 24, 2010. Owners may contact kenworth at 425-828-5440.

Steering: column

10V3080009,697 vehicles affected

The problem
Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
The risk
A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
The fix
Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

Latch

10V2660004,796 vehicles affected

The problem
Kenworth is recalling certain model year 2009 through 2010 t660 tractor trailors manufactured from july 1, 2008 through july 31, 2009. The retaining pins securing the hood strut lock tube to the hood strut assembly may become loose and fall out allowing the lock tube to rotate on the strut assembly. In its normal operation the safety latch feature is automatically set and it prevents the hood from closing. With the hood closed and the retaining pins missing, the lock tube may rotate relative to the good strut resulting in a non-operational safety latch feature when the hood is opened.
The risk
A non-operational safety latch feature may not be detected by an operator increasing the risk of personal injury and/or vehicle damage should the hood unexpectedly close.
The fix
Dealers will replace the pivot disc and lock tube retaining pins with a revised pivot disc and cap screws. This service will be performed free of charge. The safety recall began on july 15, 2010. Owners may contact kenworth at 1-425-828-5440.

Suspension: spindle

10V18500021 vehicles affected

The problem
Kenworth is recalling certain model year 2010 t2000, t660, t800 and w900 vehicles manufactured between july 30, 2009 and september 18, 2009. The rear axle outer end hub may have not been primed with oil properly during the rear axle installation process. Potential lack of oil may cause the outer end bearing to heat up and/or seize, possibly resulting in the overheating of the wheel end.
The risk
A wheel end fire may occur, increasing the risk of a crash.
The fix
Dealers will replace the bearings, seals and will add oil to the outer end hub as well as inspect races and axle housing for damage and replacing as necessary free of charge. The safety recall began on may 24, 2010. Owners may contact kenworth at 425-828-5440.

Steering

09V4900003,078 vehicles affected

The problem
Kenworth is recalling model year 2010 t2000, t800, t660 and w900s trucks manufactured between july 1 and october 23, 2009. The fasteners attaching the steering gear to the front drive bracket may have received insufficient torque during the installation process resulting in less than required clamp load.
The risk
The insufficient clamp load may allow the fastener(s) to become loose and fall away from the vehicle resulting in road debris. If multiple fasteners were to become loose, the vehicle steering may wander, which could result in a crash.
The fix
Dealers will inspect and re-torque the steering gear mounting bolts free of charge. The safety recall is expected to begin during january 2010. Owners may contact kenworth at 1-425-828-5440.

Power train: axle assembly

09V415000914 vehicles affected

The problem
Kenworth is recalling model year 2009 through 2010 t2000, t800, t660 and w900 trucks manufactured between november 12, 2008 and september 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain ag400l rear suspensions may have received insufficient fastener torque during the installation process. The insufficient torque may allow the axle u-bolt to become loose, which may cause vibration in the rear suspension.
The risk
If multiple fasteners were to become loose, the rear axle may shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.
The fix
Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on november 4, 2009. Owners may contact kenworth at 425-828-5440.

What owners say

Be the first T660 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

2 complaints about the 2010 Kenworth T660

Newest first, as filed with NHTSA by owners.

Steering

While going down long mountain grades, in hot weather, the steering locks up. I was told that it needed a oil cooler. I paid $1280.00 For an oil cooler. Trw does not think they have any responsibility to warranty a one year old steering gear. Even though they know that it is a malfunctioning relief valve. *Tr

Filed Incident SteeringNHTSA 10426705
BrakesCrash1 injury

Tl* the contact owns a 2010 kenworth t660 truck. While driving approximately 10 mph, the contact attempted to depress the brake pedal when he noticed that the vehicle was hesitant to stop. The contact was able to pull the emergency brake in order to slow the vehicle speed but the contact crashed into the vehicle positioned in front of him. The contact noticed there was a cover over the steering column which interfered when he attempting to brake. The contact stated that the brake pedal was extremely narrow and made...

Read the full complaint

it difficult to engage. A police report was filed. The contact was not injured but the driver of the second vehicle stated she recently had surgery on her shoulder and was worried about further injuries. The manufacturer was made aware of the failure and stated that an inspector would inspect the vehicle for failure. The vehicle was not repaired. The approximate failure mileage was 145,000. Updated 06/24/11 *bf the consumer marked the injury box. Updated 11/16/11

Filed Incident Service brakes, hydraulicNHTSA 10399881

Kenworth T660: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
201411100BrakesD
20130600-B
20121900Engine & coolingC
201111300BrakesD
201021010BrakesD
200901700-F
200821411Engine & coolingD
20070800-C
20060400-B
All T660 years

2010 Kenworth T660 vs rivals

VehicleComplaintsRecallsCrashesGrade
2010 Kenworth T6602101D
2010 Kenworth C500141DCompare
2010 Kenworth T8001110CCompare

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2010 Kenworth T660? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2010 Kenworth T660

Does the 2010 Kenworth T660 have any recalls?

Yes - NHTSA lists 10 recalls for the 2010 Kenworth T660: reservoir / tank (February 2024); electronic stability control (ESC) (April 2020); engine and engine cooling (March 2011); tank assembly (February 2011) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2010 Kenworth T660?

By the complaints owners filed with NHTSA, the most common problem areas are the brakes (1), steering (1).

How many complaints has the 2010 Kenworth T660 had?

2 complaints have been filed with NHTSA, the first on May 10, 2011 and the latest on September 22, 2011. Of these, 1 describe a crash and 0 a fire, and together they report 1 injury and 0 deaths.

Is the 2010 Kenworth T660 a reliable vehicle?

Its Safety Index is 35 out of 100 (grade D: more problems than a typical Kenworth T660 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Kenworth T660 years have the most complaints?
What should I do if my 2010 Kenworth T660 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience