- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."
- The risk
- Insufficient air volume can reduce braking performance and increase the risk of a crash.
- The fix
- Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.
Vehicle safety record
2010 Kenworth T800 Problems, complaints & recalls
Owners have filed 1 complaint about the 2010 Kenworth T800 with NHTSA. Those complaints describe 1 fire. It is covered by 11 recalls, the latest in February 2024 for the reservoir / tank. For comparison, the 2009 has 2 and the 2011 has 0.
NHTSA data checked
CAbout as many problems as a typical T800 year, for its age
#373 most complained-about 2010 vehicle
- Complaints
- 1
- Recalls
- 11
- Crashes
- 0
- Fires
- 1
- Injuries
- 0
- Deaths
- 0
2010 Kenworth T800 recalls 11
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
- The risk
- If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
- The fix
- PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
- The problem
- PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.
- The risk
- If engine oil comes into contact with a hot surface, there is an increased risk of a fire.
- The fix
- Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.
- The problem
- PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."
- The risk
- Brakes that take longer to apply may lengthen the distance needed to stop the truck, increasing the risk of a crash.
- The fix
- PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.
- The problem
- Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
- The risk
- The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
- The fix
- Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.
- The problem
- Paccar is recalling certain model year kenworth t660, t700, t800 and w900 vehicles manufactured from december 22, 2008, through august 2, 2010, and equipped with ag400l air disc brakes. The air disc brake caliper could be installed on the wrong side of the drive axle potentially causing interference with the suspension bracket and the rear suspension as the outermost brake pads wear and the floating caliper moves inboard.
- The risk
- As this interference gets larger, this could eventually lead to reduced braking performance, increasing the risk of a crash.
- The fix
- Dealers will verify the correct orientation of the brake caliper and perform the necessary repair free of charge. The safety recall began on november 24, 2010. Owners may contact kenworth at 425-828-5440.
- The problem
- Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.
- The risk
- A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.
- The fix
- Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.
- The problem
- Kenworth is recalling certain model year 2010 t2000, t660, t800 and w900 vehicles manufactured between july 30, 2009 and september 18, 2009. The rear axle outer end hub may have not been primed with oil properly during the rear axle installation process. Potential lack of oil may cause the outer end bearing to heat up and/or seize, possibly resulting in the overheating of the wheel end.
- The risk
- A wheel end fire may occur, increasing the risk of a crash.
- The fix
- Dealers will replace the bearings, seals and will add oil to the outer end hub as well as inspect races and axle housing for damage and replacing as necessary free of charge. The safety recall began on may 24, 2010. Owners may contact kenworth at 425-828-5440.
- The problem
- Kenworth is recalling model year 2010 t2000, t800, t660 and w900s trucks manufactured between july 1 and october 23, 2009. The fasteners attaching the steering gear to the front drive bracket may have received insufficient torque during the installation process resulting in less than required clamp load.
- The risk
- The insufficient clamp load may allow the fastener(s) to become loose and fall away from the vehicle resulting in road debris. If multiple fasteners were to become loose, the vehicle steering may wander, which could result in a crash.
- The fix
- Dealers will inspect and re-torque the steering gear mounting bolts free of charge. The safety recall is expected to begin during january 2010. Owners may contact kenworth at 1-425-828-5440.
- The problem
- Kenworth is recalling model year 2009 through 2010 t2000, t800, t660 and w900 trucks manufactured between november 12, 2008 and september 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain ag400l rear suspensions may have received insufficient fastener torque during the installation process. The insufficient torque may allow the axle u-bolt to become loose, which may cause vibration in the rear suspension.
- The risk
- If multiple fasteners were to become loose, the rear axle may shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.
- The fix
- Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on november 4, 2009. Owners may contact kenworth at 425-828-5440.
- The problem
- Paccar is recalling model year 2008-2010 kenworth t300, t270, and t370, model year 2009-2010 t800 and peterbilt model year 2008-2010 335, 340, and 367 vehicles built on cummins' diesel engine. The vehicles may be designed with a hard wired, dash-mounted switch that enables the vehicle operator to inhibit aftertreatment diesel particulate filter regeneration in environments where the operator believes it may be unsafe for elevated exhaust temperatures. Due to an issue with the logic in the ecm software in these engines, the switch may not function correctly, leading the operator to believe that the switch is in "inhibit" mode when it is not.
- The risk
- This condition will permit hot exhaust gases to exit the vehicle tailpipe, increasing the risk of melting or burning of nearby surfaces, or a fire.
- The fix
- Paccar is working with cummins to repair the engines free of charge please see 09e-046. The safety recall began on october 1, 2009. Owners may contact cummins at 1-800-diesels (1-800-343-7357).
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
1 complaints about the 2010 Kenworth T800
Newest first, as filed with NHTSA by owners.
Tru-flex torsional bellows pipe connecting engine turbo charger and exhaust pipe in engine compartment leaks hot exhaust gases into cab where operator is located. Hot exhaust gases escape from this frequently failing part and starts fires on nearby combustible components. Fmcsa part 393.83 2 E and g is violated. This problem extends at least to model year 2010 thru 2014 in several different forms. Operators are forced to replace these defective devices at their own expense. Some operators have experienced several...
Read the full complaint
small fires and there has been at least one fire destroying a truck. Most of these fires have been suppressed by the owner operators when they are small. These fires are especially common on trucks used for carrying logs in the up of michigan. One specific fire was reported to michigan state police and michigamme/spur fire department. The truck was traveling on a forest road at the time of the incident. Owner operators are in some cases now purchasing extra tru-flex connectors to have on hand because of the high failure rate. Exact dates of all fires is not known.
Kenworth T800: every year compared
All T800 years2010 Kenworth T800 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2010 Kenworth T800 | 1 | 11 | C | |
| 2010 Kenworth T660 | 2 | 10 | D | Compare |
| 2010 Kenworth C500 | 1 | 4 | D | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2010 Kenworth T800
Does the 2010 Kenworth T800 have any recalls?
Yes - NHTSA lists 11 recalls for the 2010 Kenworth T800: reservoir / tank (February 2024); electronic stability control (ESC) (April 2020); engine (May 2015); service brakes (November 2013) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
How many complaints has the 2010 Kenworth T800 had?
1 complaints have been filed with NHTSA, the first on December 10, 2016 and the latest on December 10, 2016. Of these, 0 describe a crash and 1 a fire, and together they report 0 injuries and 0 deaths.
Is the 2010 Kenworth T800 a reliable vehicle?
Its Safety Index is 43 out of 100 (grade C: about as many problems as a typical Kenworth T800 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T800 years have the most complaints?
1999 (4), 2006 (4), 2004 (3). See every Kenworth T800 year compared.
What should I do if my 2010 Kenworth T800 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data