- The problem
- On certain vehicles equipped with cummins electronic control modules on the c8.3G and l10g engines, the ecm does not have the ability to detect a throttle fail-safe engine shutdown command. This could result in an unanticipated, uncommanded open throttle condition without warning.
- The risk
- If this event occurs, the vehicle operator will not have control of the engine speed, possibly resulting in a vehicle crash.
- The fix
- Cummins will notify the customers and replace the ecm. Owners should contact cummins at 1-800-343-7357 or kenworth at 1-425-828-5440.
Vehicle safety record
1997 Kenworth T800 Problems, complaints & recalls
Owners have filed 1 complaint about the 1997 Kenworth T800 with NHTSA, most often about the equipment & accessories (1) and the wheels & tires (1). It is covered by 9 recalls, the latest in July 2003 for the vehicle speed control. For comparison, the 1996 has 1 and the 1998 has 1.
NHTSA data checked
CAbout as many problems as a typical T800 year, for its age
#338 most complained-about 1997 vehicle
- Complaints
- 1
- Recalls
- 9
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Most common 1997 Kenworth T800 problems
Share of all 1 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
1997 Kenworth T800 recalls 9
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Certain trucks equipped with meritor p 18x7 brakes with 36" brake chambers fail to comply with the requirements of federal motor vehicle safety standard (fmvss) no. 121, "Air brake systems." These trucks were manufactured with a combined air reservoir volume less than 12 times the combined volume of all service brake chambers.
- The risk
- This does not meet the requirements of the standard.
- The fix
- Dealers will add an additional tank or change one of the existing air tanks to a larger size. Owner notification began on may 5, 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5440.
- The problem
- Vehicle description: heavy duty trucks built with arvinmeritor front axle ff-981. The wheel separator plates are incompatible with skf phase iv truck hub units incorporated into the arvinmeritor ff-981 front axle assemblies installed on vehicles with wheel mounting flanges of 10 mm or less and brake drum mounting flanges of 6 mm or less.
- The risk
- The combination of components could reduce the service life of the front hub, which could result in a fracture. If a hub fractures, vehicle control, braking, and stability can be affected. In extreme cases, the wheel could separate from the vehicle causing a loss of vehicle control, increasing the risk of a crash.
- The fix
- Dealers will change the front hubs. Owner notification began december 10, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with meritor fg941 steer axles. The gross axle weight rating (gawr) was determined incorrectly and over-stated on the vehicle certification label. With the incorrect gawr listed, these labels do not meet the certification requirements of part 567, "requirements for manufacturers of motor vehicles." Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating.
- The risk
- These vehicles would not be in compliance with federal regulations.
- The fix
- Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating. Owner notification began june 22, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
- The risk
- Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
- The fix
- Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: trucks assembled with skf level 2 truck hub units (thu) received from meritor. These hubs can fatigue crack.
- The risk
- This fatigue cracking can result in wheel separation, increasing the risk of a crash.
- The fix
- Dealers will replace these hubs with production level 3 hubs.
- The problem
- Vehicle description: heavy duty trucks equipped with caterpillar 3406e engines. The routing of the electrical and fuel lines can cause chaffing of the wiring harness on the fuel line.
- The risk
- This chaffing can cause fuel leakage and a potential for a fire in the engine compartment.
- The fix
- Dealers will inspect, adjust, and repair, if necessary, the fuel line and electrical harness.
- The problem
- Vehicle description: heavy duty trucks equipped with design level 1, rockwell ff980 series front axle. The front axle hub flange can develop cracks due to high stress levels.
- The risk
- Cracks in a hub flange can result in a wheel separation.
- The fix
- Dealers will remove and replace the front hubs with an improved design level 2 hub.
- The problem
- Vehicle description: heavy duty trucks equipped with kenworth airglide 200 rear suspension. Due to materials used in the sway bar arms and studs as well as the stud plating material, stress corrosion cracking and bending fatigue can occur in the rear suspension sway bar arms and studs causing the stud to fail prematurely.
- The risk
- This could cause a loss of steering control increasing the risk of a vehicle crash.
- The fix
- Dealers will replace the arm assembly manufactured from a different material. New studs will be installed with different threads and different finish.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
1 complaints about the 1997 Kenworth T800
Newest first, as filed with NHTSA by owners.
I work for [[redacted]]. They are making me drive the truck unsafe without having any maintenance done to the truck and running over the hours from 12-20 hours a day. If they I don't take the loads they tell me to take or I am fired and I cannot afford not to work. Information redacted pursuant to the freedom of information act (foia), 5 u.S.C. 552(B)(6). *Tr
Kenworth T800: every year compared
All T800 years1997 Kenworth T800 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 1997 Kenworth T800 | 1 | 9 | C | |
| 1997 Kenworth T2000 | 3 | 4 | C | Compare |
| 1997 Kenworth Kenworth | 2 | 0 | B | Compare |
| 1997 Kenworth T600 | 2 | 4 | C | Compare |
| 1997 Kenworth W900 | 1 | 5 | B | Compare |
| 1997 Kenworth W900B | 1 | 0 | A | Compare |
| 1997 Kenworth W900L | 1 | 0 | A | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 1997 Kenworth T800
Does the 1997 Kenworth T800 have any recalls?
Yes - NHTSA lists 9 recalls for the 1997 Kenworth T800: vehicle speed control (July 2003); service brakes, air (March 2003); hub (November 2001); labels (April 2001) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 1997 Kenworth T800?
By the complaints owners filed with NHTSA, the most common problem areas are the equipment & accessories (1), wheels & tires (1), engine & cooling (1).
How many complaints has the 1997 Kenworth T800 had?
1 complaints have been filed with NHTSA, the first on May 23, 2010 and the latest on May 23, 2010. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.
Is the 1997 Kenworth T800 a reliable vehicle?
Its Safety Index is 53 out of 100 (grade C: about as many problems as a typical Kenworth T800 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T800 years have the most complaints?
1999 (4), 2006 (4), 2004 (3). See every Kenworth T800 year compared.
What should I do if my 1997 Kenworth T800 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data