- The problem
- On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.
- The risk
- Seizure of the bearings can cause wheel separation or wheel end fire.
- The fix
- Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940-591-4201 or kenworth 425-828-5440.
Vehicle safety record
2000 Kenworth T800 Problems, complaints & recalls
Owners have filed 1 complaint about the 2000 Kenworth T800 with NHTSA, most often about the electrical system (1). It is covered by 10 recalls, the latest in April 2003 for the hub. For comparison, the 1999 has 4 and the 2001 has 1.
NHTSA data checked
CAbout as many problems as a typical T800 year, for its age
#459 most complained-about 2000 vehicle
- Complaints
- 1
- Recalls
- 10
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Most common 2000 Kenworth T800 problems
Share of all 1 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2000 Kenworth T800 recalls 10
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Certain trucks equipped with meritor p 18x7 brakes with 36" brake chambers fail to comply with the requirements of federal motor vehicle safety standard (fmvss) no. 121, "Air brake systems." These trucks were manufactured with a combined air reservoir volume less than 12 times the combined volume of all service brake chambers.
- The risk
- This does not meet the requirements of the standard.
- The fix
- Dealers will add an additional tank or change one of the existing air tanks to a larger size. Owner notification began on may 5, 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5440.
- The problem
- Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4201 or kenworth at 1-425-828-5440.
- The problem
- On certain heavy duty trucks equipped with replacement dana spicer tandem drive axle models ds463 and ds521, installed on vehicles from may 1, 2001 through february 1, 2002, an undersized attachment weld may fracture without warning.
- The risk
- The loss of this attachment to the vehicle chassis can adversely affect vehicle handling or driver control.
- The fix
- Dana is conducting the owner notification and remedy for this campaign. The dealers will remove the suspect bracket, inspect the axle housing, and reweld the bracket to the axle housing. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact dana at 616-567-1088 or kenworth at 425-828-5440.
- The problem
- On some heavy duty trucks equipped with alcoa fujikura ltd. (Afl) power distribution boxes (pd box), the pd boxes were manufactured with insufficient torque applied to the nut of the main power feed-through stud.
- The risk
- Insufficient torque can lead to (1) electrical arcing of the wires inside of the pd box, or (2) an interrupted power supply to the vehicle's electrical system, either of which can lead to a loss of vehicle electrical power and possibly vehicle control without warning.
- The fix
- Dealers will inspect and tighten the nut on the main power feed-through stud. Owner notification began february 25, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5440.
- The problem
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with chalmers 1000 series and 800 series suspension kits. These suspension kits may have insufficient penetration of the weld attaching the torque rod eye to the torque rod tube.
- The risk
- Failure of the weld could result in separation of the eye and tube, causing a lock of axle retention, which could result in loss of vehicle control.
- The fix
- Dealers will replace all chalmers fixed torque rods on these vehicles. Owner notification began july 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with meritor fg941 steer axles. The gross axle weight rating (gawr) was determined incorrectly and over-stated on the vehicle certification label. With the incorrect gawr listed, these labels do not meet the certification requirements of part 567, "requirements for manufacturers of motor vehicles." Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating.
- The risk
- These vehicles would not be in compliance with federal regulations.
- The fix
- Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating. Owner notification began june 22, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
- The risk
- Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
- The fix
- Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.
- The risk
- If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.
- The fix
- Dealers will inspect and correct the problem, as needed. Owner notification began february 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
1 complaints about the 2000 Kenworth T800
Newest first, as filed with NHTSA by owners.
Air leak under dash, caused by power divider switch. *Slc
Kenworth T800: every year compared
All T800 years2000 Kenworth T800 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2000 Kenworth T800 | 1 | 10 | C | |
| 2000 Kenworth W900 | 7 | 9 | C | Compare |
| 2000 Kenworth T2000 | 2 | 6 | C | Compare |
| 2000 Kenworth Conventional Series | 2 | 0 | - | Compare |
| 2000 Kenworth T800B | 1 | 0 | C | Compare |
| 2000 Kenworth Kenworth | 1 | 0 | A | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2000 Kenworth T800
Does the 2000 Kenworth T800 have any recalls?
Yes - NHTSA lists 10 recalls for the 2000 Kenworth T800: hub (April 2003); service brakes, air (March 2003); tie rod assembly (July 2002); rear (February 2002) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2000 Kenworth T800?
By the complaints owners filed with NHTSA, the most common problem areas are the electrical system (1).
How many complaints has the 2000 Kenworth T800 had?
1 complaints have been filed with NHTSA, the first on April 6, 2001 and the latest on April 6, 2001. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.
Is the 2000 Kenworth T800 a reliable vehicle?
Its Safety Index is 49 out of 100 (grade C: about as many problems as a typical Kenworth T800 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth T800 years have the most complaints?
1999 (4), 2006 (4), 2004 (3). See every Kenworth T800 year compared.
What should I do if my 2000 Kenworth T800 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data