- The problem
- On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.
- The risk
- Seizure of the bearings can cause wheel separation or wheel end fire.
- The fix
- Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940-591-4201 or kenworth 425-828-5440.
Vehicle safety record
2000 Kenworth W900 Problems, complaints & recalls
Owners have filed 7 complaints about the 2000 Kenworth W900 with NHTSA, most often about the suspension (4) and the steering (1). It is covered by 9 recalls, the latest in April 2003 for the hub. For comparison, the 1999 has 3 and the 2001 has 1.
NHTSA data checked
CAbout as many problems as a typical W900 year, for its age
#227 most complained-about 2000 vehicle
- Complaints
- 7
- Recalls
- 9
- Crashes
- 0
- Fires
- 0
- Injuries
- 0
- Deaths
- 0
Most common 2000 Kenworth W900 problems
Share of all 7 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.
2000 Kenworth W900 recalls 9
Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do
- The problem
- Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4201 or kenworth at 1-425-828-5440.
- The problem
- On certain heavy duty trucks equipped with replacement dana spicer tandem drive axle models ds463 and ds521, installed on vehicles from may 1, 2001 through february 1, 2002, an undersized attachment weld may fracture without warning.
- The risk
- The loss of this attachment to the vehicle chassis can adversely affect vehicle handling or driver control.
- The fix
- Dana is conducting the owner notification and remedy for this campaign. The dealers will remove the suspect bracket, inspect the axle housing, and reweld the bracket to the axle housing. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact dana at 616-567-1088 or kenworth at 425-828-5440.
- The problem
- On some heavy duty trucks equipped with alcoa fujikura ltd. (Afl) power distribution boxes (pd box), the pd boxes were manufactured with insufficient torque applied to the nut of the main power feed-through stud.
- The risk
- Insufficient torque can lead to (1) electrical arcing of the wires inside of the pd box, or (2) an interrupted power supply to the vehicle's electrical system, either of which can lead to a loss of vehicle electrical power and possibly vehicle control without warning.
- The fix
- Dealers will inspect and tighten the nut on the main power feed-through stud. Owner notification began february 25, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5440.
- The problem
- Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
- The risk
- This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.
- The fix
- Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with chalmers 1000 series and 800 series suspension kits. These suspension kits may have insufficient penetration of the weld attaching the torque rod eye to the torque rod tube.
- The risk
- Failure of the weld could result in separation of the eye and tube, causing a lock of axle retention, which could result in loss of vehicle control.
- The fix
- Dealers will replace all chalmers fixed torque rods on these vehicles. Owner notification began july 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1-940-591-4000 or kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with meritor fg941 steer axles. The gross axle weight rating (gawr) was determined incorrectly and over-stated on the vehicle certification label. With the incorrect gawr listed, these labels do not meet the certification requirements of part 567, "requirements for manufacturers of motor vehicles." Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating.
- The risk
- These vehicles would not be in compliance with federal regulations.
- The fix
- Vehicles will be remedied either by assigning the proper weight rating or, if possible, by changing the necessary components to meet the currently assigned weight rating. Owner notification began june 22, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: vehicles equipped with 54" rear axle spacing configuration of the airglide 200 suspension with the service application identified as logger, dump truck, or tanker. The rear suspension is regularly subjected to extreme articulation, resulting in flexing of the joint.
- The risk
- Failure of the lower sway arm attaching bolts could result in loss of vehicle control.
- The fix
- Dealers will replace the lower sway arm brackets. Owner notification began march 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
- The problem
- Vehicle description: heavy duty trucks equipped with an optional firewall-mounted circuit breaker. The main cab power and battery power leads were attached incorrectly. This condition can result in the main cab power being unprotected.
- The risk
- If a wiring short occurred anywhere along the cab power circuit, the available battery power could arc and cause subsequent damage to the vehicle or a fire.
- The fix
- Dealers will inspect and correct the problem, as needed. Owner notification began february 26, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1-425-828-5000.
What owners say
Problems or none - your experience is exactly what the next buyer is looking for. Write it now
7 complaints about the 2000 Kenworth W900
Newest first, as filed with NHTSA by owners.
Tl*the contact owns a 2000 kenworth w900. The contact stated that the frame rail failed on three occasions. The dealer replaced them each time. The frame rail cracked and cut the power steering hose. The vehicle was parked when the contact noticed an oil leak. The current mileage is 211,000 and failure mileage was 108,000.
Consumer states that he is having electrical problems with his big rig. He states that he can be driving down the road and the lights cut off, then later on they come back on. He states that he has had this truck in the shop 60 plus times, and no one can find out what the problem is. He states he has had the motor rebuilt twice, replaced the heads, replace gasket etc at lease twice, and no one can find the problem.
Kenworth has a reputation of putting a custumer off untill warranty is out. All of these problems where to be addressed. And there are more. Hard to explain in short words. I do have documentation in the form of maint. Files with descriptive accounts of all problems , none of which have been accuratly repaired. I'v been into various shops concerning rr suspension, ride height prb. Has always been the issue. This effects every asspect of driveability, at first was thougth to be allignment but then started to notice...
Read the full complaint
similarities between the two when control valves started leaking down, after 15 or so trips to shop , I began to learn all I could about it. And after 50 or so times adjusting myself have found no real sollution. This has been a problem ever since the truck was new and is on the top of my list because not only does this creat a mechanical falure nightmare but is directly linked to certain saftey issues because trk is not very controlable. And have had several accidents due to vehicle handling and , I could talk in great lenths aboutit . Also the other items are very similar when it comes to safe opporation. Please contact me for further explanations and documentation. *Ak
Consumer states that the engine would stalls while driving 55-60 mph. Vehicle has been to the dealer and the problem reoccurring. Feel free to provide any further information. Nlm
While driving at low speed of 20 mph or less right front tie rod end broke, and caused loss of steering. Dealer contacted. Feel free to provide any further infromation.*Ak
Consumer received recall 01v051000. She made an appointment with dealership regarding this recall, and dealership informed her they had no information regarding recall. Please provide any additional information/attachments.*Ak
The truck has a vibration, which shakes bolts loose and the sleeper doors leaks. *Et
Kenworth W900: every year compared
All W900 years2000 Kenworth W900 vs rivals
| Vehicle | Complaints | Recalls | Grade | |
|---|---|---|---|---|
| 2000 Kenworth W900 | 7 | 9 | C | |
| 2000 Kenworth T2000 | 2 | 6 | C | Compare |
| 2000 Kenworth Conventional Series | 2 | 0 | - | Compare |
| 2000 Kenworth T800 | 1 | 10 | C | Compare |
| 2000 Kenworth T800B | 1 | 0 | C | Compare |
| 2000 Kenworth Kenworth | 1 | 0 | A | Compare |
More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.
Questions about the 2000 Kenworth W900
Does the 2000 Kenworth W900 have any recalls?
Yes - NHTSA lists 9 recalls for the 2000 Kenworth W900: hub (April 2003); tie rod assembly (July 2002); rear (February 2002); wiring (February 2002) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.
What are the most common problems with the 2000 Kenworth W900?
By the complaints owners filed with NHTSA, the most common problem areas are the suspension (4), steering (1), electrical system (1).
How many complaints has the 2000 Kenworth W900 had?
7 complaints have been filed with NHTSA, the first on August 1, 2000 and the latest on July 16, 2007. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.
Is the 2000 Kenworth W900 a reliable vehicle?
Its Safety Index is 41 out of 100 (grade C: about as many problems as a typical Kenworth W900 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.
Which Kenworth W900 years have the most complaints?
2000 (7), 1998 (3), 1999 (3). See every Kenworth W900 year compared.
What should I do if my 2000 Kenworth W900 has a problem?
If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.
Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data