Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Vehicle safety record

2007 Kenworth T800 Problems, complaints & recalls

Owners have filed 1 complaint about the 2007 Kenworth T800 with NHTSA, most often about the equipment & accessories (1). It is covered by 21 recalls, the latest in November 2013 for the service brakes. For comparison, the 2006 has 4 and the 2008 has 1.

NHTSA data checked

FFar more problems than a typical T800 year, for its age

#445 most complained-about 2007 vehicle

Complaints
1
Recalls
21
Crashes
0
Fires
0
Injuries
0
Deaths
0

Most common 2007 Kenworth T800 problems

Share of all 1 complaints. One complaint can name more than one area. Tap an area for its complaints and recalls.

2007 Kenworth T800 recalls 21

Recall repairs are free. Your dealer fixes them whether or not you bought the car there - check your VIN at nhtsa.gov/recalls to see if yours is done. What to do

Service brakes

13V57300018 vehicles affected

The problem
PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."
The risk
Brakes that take longer to apply may lengthen the distance needed to stop the truck, increasing the risk of a crash.
The fix
PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.

Fuel system: tank assembly

11V1270004,664 vehicles affected

The problem
Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.
The risk
The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.
The fix
Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Power train: axle assembly

10V63400012,873 vehicles affected

The problem
Paccar is recalling certain model year 2007-2008 kenworth and peterbilt vehicles manufactured from february 2, 2006 through april 30, 2007. The bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of lubrication and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. This condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle.
The risk
Detachment of the driveline from the axle may cause the vehicle to lose power and become disabled in the roadway. Also, the driveline could drop from the vehicle into the roadway increasing the risk of a crash.
The fix
Paccar is working with its supplier to remedy the vehicles free of charge. The safety recall is expected to begin during february 2011. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4196.

Service brakes

09V2390003,423 vehicles affected

The problem
Kenworth is recalling 3,423 my 2004-2009 t2000, t800,t600, w900 and t660 vehicles. Increased brake excitation in a certain vehicle configuration which includes bendix drum brakes, wide base low profile single tires, and an ag400 or ag460 rear suspension, due to its unique brake clocking and cam tube length, can cause fatigue and cracking to brake assembly components.
The risk
Cracking can cause a complete fracture of the cam tube, which could increase stopping distance and decrease parking brake hold capability.
The fix
Dealers will inspect the rear axle brakes assembly, replace cracked rear axle brakes assembly components where required, and install cam tube support brackets on all rear axle wheel ends free of charge. The recall is expected to begin or before july 25, 2009. Owner may contact kenworth at 1-425-828-5440.

Service brakes: disc

09V166000140 vehicles affected

The problem
Paccar is recalling 140 my 2005, 2007-2009 t800, w900, and t660 trucks. The caliper mounting fasteners attaching the air disc brake caliper assembly to the torque plate may have received insufficient torque during the installation process. The insufficient torque may allow the air disc brake caliper assembly to become loose and possibly separate from the vehicle.
The risk
This could result in reduced braking capacity and also a road debris hazard, increasing the risk of a crash.
The fix
Dealers will inspect air disc brake caliper assemblies and replace the caliper mounting fasteners and torque properly. This service will be performed free of charge. The manufacturer has not yet provided an owner notification schedule. Owners may contact kenworth at 1-425-828-5440.

Suspension

08V485000130 vehicles affected

The problem
Paccar is recalling 130 my 2004-2009 t2000, t800, t600, w900 and t660 kenworth trucks built with an ag400 rear suspension, long stroke brake chambers, and wide base tires (super singles). These vehicles may develop an increase in lateral and vertical axle movement. This movement may cause part or parts of the brake assembly (brake cam tube support, brake chamber bracket, brake chamber, brake spider) to develop fatigue cracks, possibly resulting in the failure of the part or parts within the brake assembly.
The risk
A failure may reduce vehicle brake performance, increasing the risk of a crash.
The fix
Dealers will install the cam tube support brackets on all of the rear axle wheel ends. Inspect the rear axle brake assembly and replace it if cracked. The recall is expected to begin during november 2008. Owners may contact kenworth at 1-425-828-5440.

Engine and engine cooling: diesel

08V4870004,883 vehicles affected

The problem
Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.
The risk
A vehicle crash could occur if another vehicle strikes the dpf on the roadway.
The fix
Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1-800-447-4986 or kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Trailer hitches: fifth wheel assembly

08V1900003,573 vehicles affected

The problem
Paccar is recalling 3,573 my 2007 kenworth c500, t800, t600, t2000, and w900 chassis built with phillips qcs ii trailer cable connection and trailer cable mounting bracket with 'u-shaped' cut out. Certain trailer cable mounting brackets have a 'u-shaped' cut out that only partially supports the trailer cable connection. Partial support of the cable connection may allow the molded boot and electrical ground pin to partially or completely pull away from the 7-way socket. Partial or complete detachment of the cable connection can cause reduced water resistance and potential loss of electrical ground. There is also a possibility the trailer lights may fail to illuminate without the operator's knowledge.
The risk
If this condition were to occur, other motorists may not be warned of the tractor/trailer movements, increasing the risk of a crash.
The fix
Dealers will install a reinforcement bracket between the flexible back of the qcs ii molded boot and the frame bracket, and reattach the supporting bolts. The recall began on may may 30, 2008. Owners may contact kenworth at 1-425-828-5440.

Trailer hitches: fifth wheel assembly

08E034000292 vehicles affected

The problem
Paccar is recalling 292 aftermarket saf holland fifth wheels sold for use on my 2007 kenworth t800 short hood, w900 long hood and t600 tractor/trailers. If the pivot bolt joint for the lever bar is over torqued, the spacer deforms, and makes contact with the lever bar. This condition coupled with corrosion associated with the seasonal dry out, can affect the lock system of the fifth wheel, preventing the fifth wheel jaw from latching securely around the trailer king pin.
The risk
The fifth wheel may fail to latch without the operator's knowledge, causing the tractor and trailer to disengage increasing the risk of a crash.
The fix
Paccar is working with saf-holland and will inspect the pivot bolt joint for a deformed spacer and replace the bolt, washer and spacer with a hex-head shoulder bolt and washer free of charge. The manufacturer has not yet provided an owner notification schecdule. Owners may contact paccar at 1-415-828-5000 Or saf-holland at 1-231-773-3271.

Trailer hitches: fifth wheel assembly

08V176000172 vehicles affected

The problem
Paccar is recalling 172 my 2007 kenworth t800 short hood, w900 long hood and t600 tractor/trailers equipped with saf-holland simplex fifth wheels. If the pivot bolt joint for the lever bar is over torqued, the spacer deforms, and makes contact with the lever bar. This condition coupled with corrosion associated with the seasonal dry out, can affect the lock system of the fifth wheel, preventing the fifth wheel jaw from latching securely around the trailer king pin.
The risk
The fifth wheel may fail to latch without the operator's knowledge, causing the tractor and trailer to disengage increasing the risk of a crash.
The fix
Kenworth is working with saf-holland simplex and will inspect the pivot bolt joint for a deformed spacer and replace the bolt, washer and spacer with a hex-head shoulder bolt and washer free of charge. The recall began on may 1, 2008. Owners may contact kenworth at 1-425-828-5440 or saf-holland at 1-231-773-3271.

Trailer hitches

08V104000318 vehicles affected

The problem
Paccar is recalling 318 my 2007-2009 kenworth t800, w900, and peterbilt 357, 365, 367, 378, 379, 384, 385, 386,388, and 389 trucks equipped with premier trailer hitch assemblies. The pintle hitch assemblies may have been manufactured in a manner resulting in a reduction of fatigue strength of the pivot pins.
The risk
This reduction of fatigue strength could cause the pivot pin to crack and eventually break, causing the trailer to detach from the truck while in motion, which could cause a crash that could result in personal injury or death.
The fix
Dealers will replace the potentially defective pivot pin free of charge. The recall began on april 18, 2008. Owners may contact kenworth at 1-425-828-5440 or peterbilt at 1-940-591-4196.

Service brakes: slack adjusters

08V099000130 vehicles affected

The problem
Paccar is recalling 130 my 2005-2007 kenworth c500, t800, w900, and peterbilt models 357 and 379 tractor trailers equipped with fabco slack adjusters on sisu axles. The slack adjusters may fail as a result of a fatigue crack rendering the slack adjuster inoperative. This could reduce braking effectiveness.
The risk
Reduction in braking capacity could increase the risk of a crash.
The fix
Dealers will inspect and replace the slack adjusters free of charge. The recall began on march 21, 2008. Owners may contact kenworth at 1-425-828-5440 and peterbilt at 1-940-591-4196.

Engine and engine cooling

07V27900028,968 vehicles affected

The problem
On certain trucks equipped with caterpillar c11, c13 or c15 engines, the oil fill cap can become dislodged due to cap damage or improper installation and become lodged in the u-joint of the steering driveline and steering gear.
The risk
If the cap becomes dodged in this area, it may result in difficulty steering the vehicle or cause complete steering lock-up increasing the risk of a crash.
The fix
Paccar is working with caterpillar to repair these vehicles. Revised oil cap retention based on the engine model/configuration will be incorporated to prevent steering lock-up. The recall began during december 2007. Owners may contact caterpillar at 1-800-447-4986 or kenworth at 425-828-5440.

Trailer hitches

07V2690009,571 vehicles affected

The problem
On certain trucks, the removable tow hitch ,when used to tow or lift a vehicle, can fail due to defective material in the tow hitch.
The risk
If the tow hitch assembly fails while a vehicle is being towed or lifted, it may cause an accident that could result in personal injury or death.
The fix
Dealers will replace the tow pin assembly free of charge. The recall began on september 4, 2007. Owners may contact kenworth at 425-828-5440 or peterbilt at 940-591-4201.

Fuel system: delivery

07V153000306 vehicles affected

The problem
On certain trucks, if the ignition switch is turned on prior to initial start up in the manufacturing plant or during the filter replacement in the field, a small flame will ignite when the fuel is added to prime the system.
The risk
The possibility exists for the flame to spread resulting in possible equipment damage or physical injury.
The fix
Dealers will inspect the filter for the date codes of the suspect filters and replace those heating elements free of charge. The recall began on march 21, 2007. Owners may contact kenworth at 425-828-5440 and peterbilt at 940-591-4201.

Power train: axle assembly

07V132000245 vehicles affected

The problem
On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.
The risk
If a fatigue failure occurs and is left unattended, the axle may lock up or the end of the axle could come off, which may result in a vehicle crash.
The fix
Dealers will inspect and replace the axles free of charge. The recall began on may 9, 2007. Owners may contact kenworth at 425-828-5440 and peterbilt at 1-940-591-4196.

Power train: automatic transmission

07V1070004,592 vehicles affected

The problem
On certain trucks, the wiring, parts, or transmission programming required for the auto neutral feature to function as designed were either not installed, connected, or programmed properly.
The risk
If any of these conditions exists, the transmission will not automatically shift into neutral when left in drive with the parking brake set engaged. The vehicle could move without warning increasing the risk of a crash.
The fix
Dealers will inspect the affected vehicles to ensure the auto neutral feature functions properly and, if needed, will make the necessary repairs free of charge. The recall began on may 9, 2007. Owners may contact kenworth at 425-828-5440.

Service brakes

07V09000065 vehicles affected

The problem
Certain trucks fail to comply with the brake timing regulatory requirements of federal motor vehicle safety standard no. 121, "Air brake systems." The brake valve was moved to the opposite rail, increasing the length of the air line, which in turn increased the wheelbase requiring a dual relay valve system. The vehicles were manufactured with a single valve system.
The risk
If stopping distance was limited, a vehicle crash could result.
The fix
Dealers will convert the single relay valve to a dual relay valve system free of charge. The recall began on may 21, 2007. Owners may contact kenworth at 425-828-5440.

Service brakes

07V0730001,377 vehicles affected

The problem
Certain trucks fail to comply with the requirements of federal motor vehicle safety standard no. 121, "Air brake systems." The trailer light line may have been routed using too tight of a bend radius. This routing method could cause the wires within the harness plug to be pulled away from the chassis plug resulting in an intermittent or complete electrical power loss to the trailer.
The risk
Should power be lost, the electrical circuits would not provide power to the antilock system on the towed vehicle increasing the risk of a crash.
The fix
Dealers will reroute the light line to eliminate the excessive bend radius and replace any plug or harness that has been damaged free of charge. The recall began on april 16, 2007. Owner may contact kenworth at 425-828-5440.

Steering: column

06V447000443 vehicles affected

The problem
On certain trucks equipped with a trw tilt/telescoping steering column, the tilt locking mechanism on the steering column may disengage. This could prevent the steering column from locking in to predetermined positions.
The risk
Should the locking mechanism disengage, the tilting travel of the column would be unrestricted. This unrestricted travel allows the steering wheel to impact the dash and could limit the movement of the steering wheel potentially resulting in difficulty maneuvering the vehicle, increasing the risk of a crash.
The fix
Dealers will replace the tilt locking mechanism with a revised design that incorporates a new bracket for restraining the tilting mechanism. The recall began on december 22, 2006. Owners may contact kenworth at 1-425-828-5440.

Vehicle speed control: cruise control

06V446000116 vehicles affected

The problem
An incorrect switch was installed in the cruise control system on certain model t300 trucks.
The risk
A light application of the brakes will not deactivate the cruise control and the system will have to be shut off by the dash switch. This could lead to unintended acceleration and a crash without warning.
The fix
Kenworth will install the correct sensor switch. The recall began on january 10, 2007. Owners may contact kenworth at 1-425-828-5440.

What owners say

Be the first T800 owner to share.

Problems or none - your experience is exactly what the next buyer is looking for. Write it now

1 complaints about the 2007 Kenworth T800

Newest first, as filed with NHTSA by owners.

Equipment & accessories

Tl*the contact drove a 2007 t800 kenworth truck. When driving approximately 10 mph in reverse and trying to lock the trailer in place, the fifth wheel handle failed to lock which caused the fifth wheel to slide. The mechanic told her that she would need to manually lock the trailer. She also stated that all of the trucks were experiencing the same failure and the company was not willing to correct the failure. The current and failure mileage was 170,950.

Filed Incident Trailer hitchesNHTSA 10312017

Kenworth T800: every year compared

YearComplaintsRecallsCrashesFiresTop problemGrade
201101300-C
201011101-C
200921910Electrical systemD
200812500Fuel systemF
200712100Equipment & accessoriesF
200641303Electrical systemD
200531201Body, doors & structureD
200431212Electrical systemD
20031700LightsB
All T800 years

2007 Kenworth T800 vs rivals

More sales usually means more complaints, so compare similar vehicles of the same year. The grade compares each vehicle with its own model's other years.

Own a 2007 Kenworth T800? Share your experience.

Your experience goes live straight away and helps every owner and buyer who checks this vehicle. Anonymous, free, no account.

Overall, how would you rate it? *

0/4000 · Please leave out names, phone numbers and your full VIN.

By posting you confirm it's your own, honest experience and agree to the rules. Safety defect? Also report it to NHTSA - that's how recalls start.

Questions about the 2007 Kenworth T800

Does the 2007 Kenworth T800 have any recalls?

Yes - NHTSA lists 21 recalls for the 2007 Kenworth T800: service brakes (November 2013); tank assembly (February 2011); axle assembly (December 2010); service brakes, air (June 2009) and more. Recall repairs are free at any authorized dealer. Enter your VIN at nhtsa.gov/recalls to see whether yours has been fixed.

What are the most common problems with the 2007 Kenworth T800?

By the complaints owners filed with NHTSA, the most common problem areas are the equipment & accessories (1).

How many complaints has the 2007 Kenworth T800 had?

1 complaints have been filed with NHTSA, the first on February 19, 2010 and the latest on February 19, 2010. Of these, 0 describe a crash and 0 a fire, and together they report 0 injuries and 0 deaths.

Is the 2007 Kenworth T800 a reliable vehicle?

Its Safety Index is 24 out of 100 (grade F: far more problems than a typical Kenworth T800 year, for its age). The index weighs complaints, crashes, fires, injuries, deaths and recalls against how long the vehicle has been on the road, compared with the same model's other years. It is not a measure of every repair - read the complaints and owner experiences, and have any used vehicle inspected before you buy.

Which Kenworth T800 years have the most complaints?
What should I do if my 2007 Kenworth T800 has a problem?

If it is a safety problem, stop driving it if it is unsafe and contact your dealer. Report it to NHTSA at nhtsa.gov/report-a-safety-problem - enough reports start investigations and recalls - and share your experience here so other owners know what to look for.

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked . Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience