Check a vehicle VIN check Latest recalls Latest complaints Common problems Rankings Compare vehicles Recall roundups All makes Guides Share your experience
Theme

Suspension

Mazda MAZDASPEED3 Suspension problems by year

7 complaints filed with NHTSA about the Mazda MAZDASPEED3's suspension. Broken springs, struts, control arms, ball joints, noises and alignment that won't hold.

Suspension complaints by model year

YearSuspension complaintsCrashesInjuriesRecalls
20101010
20082000
20074000

Latest MAZDASPEED3 suspension complaints

2010 Mazda MAZDASPEED3SuspensionAirbags1 injury

Tl* the contact owns a 2010 mazda 3. While driving 70 mph, the driver side curtain air bag inadvertently deployed without warning or impact. The contact sustained a minor bruise to the ribs. Medical attention was not required. The vehicle was taken to a local dealer (fairway mazda of savannah 10101 abercorn street, savannah, ga, 31406), but the cause of the failure could not be determined. The manufacturer was notified of the failure and sent out an engineer who determined that the vehicle had front passenger side suspension damagae, which caused the air bag deployment. The vehicle was taken to an independent mechanic and was repaired. The failure mileage was approximately 63,000.

Filed Incident Suspension · Air bagsNHTSA 11015673
2007 Mazda MAZDASPEED3Suspension

Tl* the contact owns a 2007 mazda, mazdaspeed3. While driving approximately 30 mph on an uneven road surface, the contact heard a clunking noise coming from the front end of the vehicle. The failure recurred sporadically. The vehicle was not diagnosed or repaired. There was a technical service bulletin under nhtsa action number: 10023313 (suspension: front). The manufacturer was made aware of the problem. The approximate failure mileage was 41,000.

Filed Incident SuspensionNHTSA 10406246
2008 Mazda MAZDASPEED3SuspensionEngine & coolingTransmission & drivetrain

2008 Mazda 3. Consumer states persistent clunking noise from the suspension and two of engine mounts are coming loose *tgw the dealer determined the noise was coming from the rear shocks and replaced them. The noise, however persisted. The consumer decided to take the vehicle to an independent repair shop and they determined that both front axles needed to be replaced and there was a crack in the cv boot. The consumer then went back to the dealer to have them inspect the vehicle. The dealer determined the struts mounts, rear sway bar links, bushings and clams all needed to be replaced. *Jb

Filed Incident Suspension · Engine and engine cooling · Power trainNHTSA 10392039
2008 Mazda MAZDASPEED3SuspensionTransmission & drivetrainBody, doors & structure

A motor mount broke on my 2008 mazdaspeed3 causing the need for replacement on the following parts: transmission two motor mounts bypass valve vehicle wiring harness drivers side axle my dealership took pictures and sent them to mazda. Mazda says the vehicle was over driven and this is why the mount failed. They will not warranty the damages and repairs. The vehicle is less than three months old. The day after the vehicle was purchased there was a noise coming from the vehicle that was abnormal. There was...

Read the full complaint

an appointment scheduled with the dealership to have this looked at. The motor mount failed before this appointment. This could be related to the failure. I don't feel that pictures can determine that it was not a defect. Also, people drove the car before I did and that could cause the belief of being over driven. Test drives with customers would be what I'm referring to. Also, we don't know how hard the sales people drove the car either. There have also been reports of this same issue happening to other people. Some of those were warranted. *Tr

Filed Incident Suspension · Power train · StructureNHTSA 10239375
2007 Mazda MAZDASPEED3SuspensionWheels & tiresEquipment & accessories

I installed the aftermarket mazdaspeed lowering springs on my mazdaspeed3, carefully following the supplied instructions. The instructions require removing the bump stops from the strut mounts. I thought this was strange, but I did it, and later found that my right-front tire tread surface had made contact with the top of the inside of the fender. The result was deep circumferential grooves in the tire, and the plastic fender liner was completely worn away in one area. This is potentially very dangerous since it could lead to a tire blowout. And yes, I am certain that the instructions show the removal of the bump stops. I have the instructions and photos of the damage. *Tr

Filed Incident Suspension · Tires · EquipmentNHTSA 10224508
2007 Mazda MAZDASPEED3Suspension

Rear wheel stabilizer bolt loose and damaged. Makes a "clunk" sound when going over small bumps. Bolt is loose and will come off. *Tr

Filed Incident SuspensionNHTSA 10210062
2007 Mazda MAZDASPEED3Suspension

Heard rattle in rear of car. The passenger's side anti roll bar linkage was loose. The nut that secured the linkage was so loose that I was able to turn it with my finger. Dealer found the nut to be loose and torqued it to 40 feet-lb per the manual. *Ak

Filed Incident SuspensionNHTSA 10190852

Source: U.S. National Highway Traffic Safety Administration (NHTSA) complaints and recalls, checked daily. Complaints are owners' own reports and are not verified. How we use the data

Owners helping owners

Know before you drive.

Every experience you share - good or bad - shows on that vehicle's page and helps the next owner and buyer. Two minutes, anonymous.

Share your experience